Pool Resurfacing Surface & Quote Calculator

Measure the inside of a rectangular pool with a level or sloped floor. The scaled profile shows where the depths change, and the takeoff separates floor, sidewalls, end walls, the waterline band and measured adjustments. Compare two quotes on the same finish area using their stated coverage, whole packs, material price, labor and fixed charges.

Pool finish planning

Compare pool resurfacing quotes

Measure the actual sloped shell, deduct the waterline band, and compare whole-pack coverage, labor and fixed charges.

Finish area and quote comparison

945 ft²

Net pool finish area · 30 ft long × 15 ft wide

Quote A

$6,183.50–$6,390.50

41–47 whole packs

1,020.6 ft² allocated to materials after allowance.

Quote B

$6,129.00–$6,255.00

39–42 whole packs

992.25 ft² allocated to materials after allowance.

Modeled cost ranges overlap

Quote B minus A -$261.50 to +$71.50

Both bars use the same cost scale. The solid portion reaches the lower total and the hatched portion extends to the upper total.

Measure the pool surface

Use a rectangular inside outline. Measure all floor depths from one level reference at the top of the wall finish.

Use added area for steps or benches outside the baseline geometry. Exclude any baseline faces they replace. The waterline band is deducted separately.

Floor segment 1
Floor segment 2
Floor segment 3
Edit finish coverage and quotes

Use coverage for the product and thickness in your quote. Use the same lower and upper values for a single coverage figure.

Quote A
Quote B

Pool floor and wall profile

The drawing follows the pool length. Depth uses a separate scale to keep floor slopes visible.

Pool section from the first end to the last3 ft deep at 0 ft. 3 ft deep at 8 ft. 8 ft deep at 20 ft. 8 ft deep at 30 ft. Waterline band 0.5 ft.
Floor profileLong wallExcluded waterline band

Segment 1

3 ft to 3 ft deep

8 ft floor length

Segment 2

3 ft to 8 ft deep

13 ft floor length

Segment 3

8 ft to 8 ft deep

10 ft floor length

Show surface and quote ledger
Sloped floor
465 ft²
Two long walls
340 ft²
Two end walls
165 ft²
Gross interior
970 ft²
Waterline band deducted
-45 ft²
Additional surface
30 ft²
Other area excluded
-10 ft²
Net finish area
945 ft²

Quote A charges

Lower material
$1,414.50
Upper material
$1,621.50
Labor
$3,969.00
Fixed charges
$800.00

Quote B charges

Lower material
$1,638.00
Upper material
$1,764.00
Labor
$3,591.00
Fixed charges
$900.00

Export the resurfacing estimate

Save the surface takeoff, floor dimensions, coverage and total-cost bounds.

Download resurfacing CSV
Show selectable CSV

How to use this calculator

  1. Choose Sloped floor with tile or Flat floor and fixed coverage to start from a worked example.
  2. Enter the inside width and the first depth. Enter each segment’s horizontal run and ending depth, in order. Keep a level portion as a segment with equal start and end depths.
  3. Keep all lengths and depths in feet. Deduct a uniform waterline band by entering its height. Use the two area adjustments for separately measured steps, benches, cutouts or other finish boundaries.
  4. For each quote enter the coverage range per pack, material allowance, material price, labor per finished square foot and fixed charges for the work included.
  5. Compare the total ranges, review the scaled floor profile and open the surface and quote ledger. Save the CSV with the project measurements and pricing assumptions.

The Formula

The mathematical logic powering this calculation is:

Let W be interior width, x the horizontal run of a floor segment, and d₁ and d₂ its endpoint depths measured from the top of the wall. The actual floor length is √(x² + (d₂ − d₁)²) and its finish area is W times that length. Each pair of long sidewalls for the segment contributes x(d₁ + d₂), the combined areas of two trapezoids. The two end walls contribute W times the sum of the first and last depths. Add these components over all segments to find the gross shell surface.
A uniform full-perimeter waterline band of height h covers 2(W + total horizontal length)h. Subtract that band and any measured surface exclusions, and add any separately measured finish area. Use an exclusion for baseline area displaced by a step or bench and an addition for the exposed faces that receive the finish. For complex shapes, measure each component separately before entering an adjustment.
For each quote, multiply net finish area by 1 + material allowance percentage/100. Divide that order area by the higher coverage and round up for the lower order quantity. Dividing by the lower coverage and rounding up gives the upper quantity. When your supplier gives one nominal coverage, enter it in both fields. Material cost equals whole packs × entered price. Labor equals the net finish area × the entered labor rate, rounded to cents. Add material, labor and the entered fixed charges for the total range. Compare the price difference by subtracting Quote A’s upper total from Quote B’s lower total for the minimum, and subtracting Quote A’s lower total from Quote B’s upper total for the maximum. A negative difference favors Quote B and a positive difference favors Quote A. These bounds assume each quote can reach its endpoints independently. Whole-pack orders make possible totals discrete.
The model accepts inside width 1–100 ft, 1–4 horizontal floor runs of 0.1–300 ft each, and endpoint depths 0.1–30 ft. Band height may be up to the shallowest endpoint. Added and excluded measured areas may each be 0–100,000 ft², subject to a positive net area and exclusions no larger than the uncovered baseline. Coverage is 1–1,000 ft² per pack and allowance is 0–100 percent. Price per pack is $0–$10,000, labor is $0–$1,000/ft² and fixed charges are $0–$100,000. Dimensions, areas, coverage and allowance allow up to three decimal places. Prices are in USD with up to two decimal places. For stable pack rounding the calculation rounds an irrational slope length upward to the nearest billionth of a foot.
The geometry assumes constant width, vertical walls, a uniform waterline band and straight longitudinal floor segments, with feature areas entered separately. The estimates use the supplied prices and included work. Taxes and other charges belong in the entered rates or fixed charges if they apply.

Worked Example

If you input:

  • Inside pool: 15 ft wide × 30 ft long, with an 8 ft shallow run at 3 ft, a 12 ft slope to 8 ft, and a 10 ft deep run
  • Finish boundaries: 0.5 ft full-perimeter band, 30 ft² measured addition and 10 ft² measured exclusion
  • Quote A: 22–25 ft² per pack, 8% material allowance, $34.50 per pack, $4.20/ft² labor and $800 fixed
  • Quote B: 24–26 ft² per pack, 5% material allowance, $42 per pack, $3.80/ft² labor and $900 fixed

Result:

The gross shell area is 970 ft² and the net finish area is 945 ft². Quote A needs 41–47 packs and costs $6,183.50–$6,390.50. Quote B needs 39–42 packs and costs $6,129.00–$6,255.00. The modeled cost ranges overlap.

Frequently Asked Questions

How do I find the square footage for pool resurfacing?

For a rectangular pool, add the actual floor surface plus both long walls and both end walls. Deduct the waterline band and other areas outside the finish. Use separately measured adjustments to account for features such as steps and benches.

Do I enter sloped length or horizontal distance?

Enter the horizontal run of each floor segment. The calculator combines the run with the change in depth to find the actual sloped floor length. For a flat segment the two lengths are equal.

What number should I enter for coverage?

Use the current product sheet or your written quote, in square feet per purchasable pack at the specified job thickness. Enter identical lower and upper coverage values if you have one figure. Quote A starts with the published 22–25 ft² range for one example finish and all displayed prices are illustrative.

Why do the two prices overlap?

Actual pack quantity depends on the coverage achieved. An overlapping interval means the entered assumptions allow cost bounds in common. The ledger shows the individual endpoints and the entered items that drive them.

Can I estimate a curved pool or a floor that slopes side to side?

The profile models a rectangular pool with constant width, vertical walls and depth changes along its length. A curved, tapered or cross-sloped surface needs a separate surface takeoff.

Similar Calculators