Pool Filter Sizing & Flow Schedule Calculator
Compare two pool filter and run-time setups for one pool. Enter filter area, flow rating and the measured or estimated flow through the filter during each run. The calculator separates total daily circulation from peak-flow fit, and shows when the entered daily amount is first reached.
Compare pool filter flow schedules
Compare how much water two schedules circulate and check every run against its entered filter flow rating.
Daily throughput and flow limits
Target 30,000 US gal in one day
Setup A
31,200 US gal
1.3 equivalent pool volumes per day
- Daily volume target reached
- First reached at 9.8 h
- A run exceeds the entered rating
- Peak 100 GPM · Rating 90 GPM
30,000 US gal if above-rating runs are counted at the rating.
Setup B
30,600 US gal
1.275 equivalent pool volumes per day
- Daily volume target reached
- First reached at 9.867 h
- All runs within entered rating
- Peak 75 GPM · Rating 120 GPM
Pool volume and daily target
Use your own target. One equivalent pool volume means the entered pool volume passed through the filter in total.
Use rated filter specs and measured or estimated flow through the filter at each setting.
Setup A
Setup B
Cumulative water through each filter
Each line follows the entered runs in order. A level tail shows the remaining idle hours.
Show filter and run ledger
Setup A
- Effective media area
- 240 ft²
- Scheduled and idle hours
- 10 h running · 14 h idle
- Scheduled average flow
- 52 GPM
- Average needed during entered run hours
- 50 GPM
- Peak / rated media loading
- 0.417 GPM/ft² / 0.375 GPM/ft²
- Peak above entered rating
- 10 GPM
- Volume at the entered rating cap
- 30,000 US gal
Run 1 · 0 h to 8 h
40 GPM · 19,200 US gal through filter
19,200 US gal cumulative
Run 2 · 8 h to 10 h
100 GPM · 12,000 US gal through filter
31,200 US gal cumulative
Above entered rating
Setup B
- Effective media area
- 320 ft²
- Scheduled and idle hours
- 10 h running · 14 h idle
- Scheduled average flow
- 51 GPM
- Average needed during entered run hours
- 50 GPM
- Peak / rated media loading
- 0.234 GPM/ft² / 0.375 GPM/ft²
- Headroom at peak
- 45 GPM
- Volume at the entered rating cap
- 30,600 US gal
Run 1 · 0 h to 8 h
45 GPM · 21,600 US gal through filter
21,600 US gal cumulative
Run 2 · 8 h to 10 h
75 GPM · 9,000 US gal through filter
30,600 US gal cumulative
Export the filtration comparison
Download filter comparison CSVShow selectable CSV
How to use this calculator
- Enter the actual pool water volume and the daily throughput target you want to compare.
- For each setup, enter the effective filter area and flow rating published for that model and application.
- Enter each run duration and the measured or estimated GPM that passes through the filter. Use separate runs when the flow changes.
- Check the daily throughput and each setup’s peak against its rating. Review the estimated target time and the rating-limited comparison when a run exceeds the rating.
- Open the filter and run ledger or save the CSV to keep the inputs, run volumes and comparison.
The Formula
The mathematical logic powering this calculation is:
Use the water volume V in US gallons and your daily target T in equivalent pool volumes. Target throughput is V × T. For each consecutive run with flow q in US gallons per minute and duration t in hours, throughput is 60 × q × t. Add run volumes to get scheduled throughput, then divide by V to get equivalent pool volumes per day. The remaining time to 24 hours contributes zero throughput. The chart accumulates entered runs from elapsed hour zero and places all remaining idle hours at the end.
Compare each run with the entered published filter rating in GPM. Headroom is rating minus peak entered flow. Media loading in GPM per square foot is flow divided by effective filter area. The same calculation at the entered rating gives a reference loading for that particular filter. Use the rating listed for your model and application. The calculator does not extrapolate a model’s rating from its filter area.
Required average during the scheduled runs is target throughput divided by their total minutes. Scheduled average uses scheduled throughput in that same calculation. The first target time is the cumulative time before the crossing run plus remaining gallons divided by that run’s GPM and 60. Rating-limited throughput replaces above-rating flow with the entered rating for arithmetic comparison at unchanged durations. Actual delivered flow depends on the pump, plumbing and pressure losses.
Inputs accept up to three decimal places. Water volume is 100–1,000,000 US gal and the entered target is 0.001–24 equivalent volumes per day. Filter area is 0.1–100,000 ft². Ratings and run flows are 0.001–1,000 GPM. Enter one to four positive runs per setup, each at least 0.001 hour and all totaling at most 24 hours. Values are compared before display rounding.
The two checks compare the entered volume and flow conditions. Turnover describes throughput in units of total pool volume and does not establish that every portion of water has passed through the filter. Sanitation, pump operating point, pressure limits and regulatory requirements are separate from this worksheet.Worked Example
If you input:
- Pool water and target: 24,000 US gal, 1.25 equivalent pool volumes per day
- Setup A: 240 ft², 90 GPM rating, 8 h at 40 GPM plus 2 h at 100 GPM
- Setup B: 320 ft², 120 GPM rating, 8 h at 45 GPM plus 2 h at 75 GPM
Result:
The daily target is 30,000 US gal. Setup A circulates 31,200 US gal, with one run 10 GPM above the entered rating. Counting that run at 90 GPM brings its total to 30,000 US gal. Setup B circulates 30,600 US gal with both runs within the entered rating.
Frequently Asked Questions
How do I work out what pool filter size to compare?
Compare the flow through the proposed filter with the rating published for that exact filter and application. Enter the filter’s effective area to see its loading in gallons per minute per square foot. The calculator reports the peak of your schedule and its margin to the entered rating.
Can the daily volume target be reached while the filter rating is exceeded?
Yes. Daily throughput adds gallons across every run, and the filter rating is checked against each run separately. The mixed-speed example shows a schedule that reaches its volume target while one run exceeds the entered 90 GPM rating.
How does the calculator model two pump speeds?
Enter one run per known flow through the filter and its duration. Use GPM measured or estimated under the conditions at that setting. Revolutions per minute alone do not give delivered GPM because the plumbing and equipment affect flow.
What does one equivalent pool volume mean?
It represents an amount of water equal to the entered pool volume. For example, 30,000 gallons circulated through a filter on a 24,000 gallon pool equals 1.25 equivalent pool volumes. The calculation tracks total throughput and assumes no particular mixing pattern.
What is the volume at the entered rating cap?
It is the arithmetic result when every entered run above the rating is counted at the rating for its original duration. This comparison helps isolate how much of the schedule total came from above-rating entries. It does not determine what a real system delivers.
Why can two filters with different areas share a similar flow rating?
The published flow can depend on the filter assembly and the rating basis as well as area. Enter the area and flow rating independently using the manufacturer documentation for the model under comparison.
Similar Calculators
Pump Curve & Operating Point Planner
Compare pump curves and speeds against system head. Visualize operating flow, runtime, electrical energy and whether your target volume fits the available hours.
Pump Flow per Hour Calculator
Pump Flow per Hour for the exact fields in this tool, with clear inputs and an immediate result for planning or comparison.
Pool Salt Calculator
Estimate pool salt mass from measured and target salinity, water volume and purity. Compare the amount to add with whole bags to buy and measurement scenarios.
Pool Resurfacing Surface & Quote Calculator
Calculate pool resurfacing square footage and compare two quotes. Measure the sloped surface, subtract waterline tile and estimate whole finish bags at both coverage bounds.
