Pool Salt Calculator
Plan a salt addition from a known pool volume or a simple water-shape estimate. Enter a measured salt level, your equipment's target and product purity to separate the calculated addition from whole bags to purchase. Compare measurement scenarios and export the breakdown; this estimates mass, not water safety or product suitability.
Plan the salt your pool needs
Compare a measured salt level with your equipment's target. Separate the calculated addition from bags to buy, then see how measurement differences affect the estimate.
Water volume
Use a known water volume when available; geometry is an estimate of the water actually present.
Accepted water volume: 1–1,000,000 L. US gallons are not Imperial gallons.
Try a pool example
Illustrative 1,000 ppm increase using pure salt and 25 kg bags.
Estimate volume from 8 × 4 m and 1.5 m average water depth; compare purity and bag remainder.
See why adding salt cannot reduce the concentration to a lower target.
Measured salt, target and product
Enter a recent measurement. In this dilute-water model, 1 ppm is treated as 1 mg/L.
The initial 3,200 ppm is an illustrative input. Use the target specified for your own equipment and situation.
Use the labelled purity of an approved pool-salt product. The model's 90–100% numeric range is not a suitability recommendation.
Bag size changes purchasing quantities, not the amount of salt the water needs.
What if the measurements differ?
Choose 0–25%. This is an assumed range, not an accuracy claim about your pool measurement.
Choose 0–1,000 ppm to explore test-reading differences. A lower scenario concentration stops at zero.
Calculated product mass to add
50 kg
50 kg pure salt, adjusted for 100% product purity. Confirm measurements and product guidance before use.
Whole bags to purchase
2 bags
50 kg of product in total. The bag count is a purchase estimate, not an instruction to add every bag.
Product left unused
0 kg
Keep this amount out of the calculated addition. Counts use unrounded masses; displayed values are estimates.
Modeled water volume: 50,000 L (13,208.6026 US gallons). Using your known-volume entry.
Measured, targeted and modeled salt level
This compares concentrations, not a manufacturer-approved operating range. The selected target is an input.
Salt addition and purchase breakdown
The addition and purchasing quantities are different. Whole-bag rounding does not increase the intended addition.
| Quantity | Value |
|---|---|
| Measured salt | 2,200 ppm |
| Selected target | 3,200 ppm |
| Positive increase being modeled | 1,000 ppm |
| Pure salt required | 50 kg |
| Product mass to add | 50 kg |
| Whole bags to purchase | 2 |
| Purchased product mass | 50 kg |
| Leave unused | 0 kg |
| Concentration after calculated addition | 3,200 ppm |
Measurement sensitivity
Four endpoint combinations of your assumed volume and salinity ranges. These are scenarios, not confidence intervals or dosing instructions.
Product required across scenarios
40.5 kg – 60.5 kg
Recalculates the product mass for each scenario's actual volume and starting concentration.
If the nominal addition is used
3,009.091 – 3,411.111 ppm
Keeps the main result's addition fixed while the assumed actual measurements change. It can overshoot or undershoot your target.
| Scenario | Water (L) | Starting ppm | Required product (kg) | ppm after nominal addition |
|---|---|---|---|---|
| Lower volume / lower measured salt | 45,000 | 2,100 | 49.5 | 3,211.111111 |
| Lower volume / higher measured salt | 45,000 | 2,300 | 40.5 | 3,411.111111 |
| Higher volume / lower measured salt | 55,000 | 2,100 | 60.5 | 3,009.090909 |
| Higher volume / higher measured salt | 55,000 | 2,300 | 49.5 | 3,209.090909 |
View CSV text
CSV uses canonical litres, kilograms and ppm with unrounded numeric results. It includes your entered assumptions and sensitivity scenarios.
Method, product guidance and precision
Pure salt mass in kg = water volume in litres × the positive target-minus-measured concentration difference in mg/L ÷ 1,000,000. Product mass divides that by the purity fraction. Bag count rounds the unrounded product-to-bag ratio upward; unused product is purchased mass minus the calculated addition. At or above target, the calculated addition is zero and the modeled concentration remains the measured level.
This treats 1 ppm as approximately 1 mg/L in dilute water, holds water volume fixed, and ignores displacement, temperature-dependent density, loss and chemical interactions. The calculation is an estimate, not an exact prediction of a subsequent water test. Use equipment and approved-product guidance for targets, suitability and handling; verify measurements and retest according to that guidance.
Rectangle volume is length × width × average water depth. Circle area is π × diameter² ÷ 4; an oval is modeled as an ellipse with area π × full length × full width ÷ 4. Both multiply area by average water depth. These shapes assume a constant horizontal footprint and vertical sides. Their geometry is computed with ordinary floating-point arithmetic, including the approximation to π; irregular pools and steps are not modeled.
Salinity text accepts up to six decimal places; authored volume, dimension, mass and other numeric text accepts up to twelve. Decimal rational arithmetic determines product mass and the whole-bag ceiling from the canonical quantities, without snapping near-integer bag counts. Geometry volumes remain approximations. Unit switches retain the canonical quantity while its converted text is unchanged, avoiding repeated-conversion drift. CSV and whole-bag counts use unrounded model values; very small nonzero display amounts use scientific notation.
The model accepts 1–1,000,000 L, dimensions 0.01–100 m, salinity 0–10,000 ppm, purity 90–100% and bags 0.1–100 kg. These are calculation limits, not recommended water conditions or product specifications. Sensitivity endpoint calculations can extend beyond the direct-entry volume/salinity limits, using only your chosen ± range; they are not new permitted direct inputs.
The Hayward AquaRite owner’s manual, revision G, pages 4–5 explains testing existing salt and using the equipment’s own target and salt-addition chart. Its 3,200 ppm example target and greater-than-99% salt specification apply to that equipment; the planner does not recommend a 90%-pure product or impose one target on all systems. Manual checked October 26, 2026.
Unit constants are exact: 1 US gallon = 3.785411784 L, 1 lb = 0.45359237 kg and 1 ft = 0.3048 m. NIST SP 1038 defines a US gallon as 231 cubic inches and an inch as 2.54 cm; these give the litre factor. NIST Handbook 130 conversion tables give the exact foot and pound relationships.
How to use this calculator
- Choose Known volume, Rectangular pool, Circular pool or Oval pool. Use inside water dimensions and average water depth; the oval model is an ellipse with vertical sides. Prefer a measured volume for irregular pools, steps or complex floors.
- Choose litres or US gallons for known volume, or metres or feet for dimensions. A valid unit switch preserves the physical quantity. Incomplete measurements keep their existing text and unit until corrected; switching volume methods retains each method's saved values.
- Enter a recent Measured salt level and Your equipment's target in ppm. The initial 3,200 ppm target is illustrative, not a recommendation for every chlorinator. Verify the target and approved salt product against your equipment guidance.
- Enter Product salt purity and Product per bag. Read the calculated mass to add separately from the whole-bag purchase count and amount to leave unused. Do not assume all purchased product belongs in the calculated addition.
- Open What if the measurements differ? to choose volume and salinity variations. Inspect the range of required masses and the resulting concentrations if the nominal addition is used. These are assumed scenarios, not confidence intervals or instructions to add a different dose.
- Check Salt addition and purchase breakdown, then Download CSV or copy View CSV text. At or above the selected target, no positive addition is calculated; follow equipment guidance and verify measurements rather than treating a negative salt dose as a solution.
The Formula
The mathematical logic powering this calculation is:
Positive concentration increase = max(target − measured salt, 0).
Under the dilute-water convention 1 ppm ≈ 1 mg/L: pure salt kg = water litres × positive increase ÷ 1,000,000.
Product kg = pure salt kg ÷ (purity percent ÷ 100).
Whole bags to buy = ceiling(unrounded product kg ÷ kg per bag). Product left unused = purchased product kg − product kg to add.
Rectangle volume = length × width × average water depth; circle = π × diameter² ÷ 4 × average depth; oval (ellipse) = π × full length × full width ÷ 4 × average depth. Metres cubed × 1,000 gives litres.
Sensitivity recalculates the required mass at four combinations of volume ± variation and measured salt ± variation, with concentration bounded below at zero. It also holds the nominal dose fixed and calculates each scenario's resulting concentration. Volume stays fixed within each calculation; no displacement or draining is modeled.Worked Example
If you input:
- Volume method: Known volume
- Water volume (L): 50000
- Measured salt level (ppm): 2200
- Your equipment's target (ppm): 3200
- Product salt purity (%): 100
- Product per bag (kg): 25
- Water-volume variation (±%): 10
- Measured-salt variation (±ppm): 100
Result:
The selected increase is 1,000 ppm. Under the fixed-volume, dilute-water convention, 50,000 L × 1,000 mg/L ÷ 1,000,000 gives 50 kg of pure salt. At 100% purity, the calculated product addition is 50 kg: two 25 kg bags, with no remainder. The modeled concentration after that addition is 3,200 ppm. With the entered measurement variations, scenario-specific product requirements range from 40.5 kg to 60.5 kg; those scenarios are not alternative dosing instructions.
Frequently Asked Questions
How much pool salt do I need to add?
The mass depends on water volume, the measured-to-target concentration increase and product purity. In this dilute-water model, litres × positive ppm increase ÷ 1,000,000 gives kilograms of pure salt. Divide by the purity fraction for product mass. For example, a 50,000 L pool with a 1,000 ppm increase needs a modeled 50 kg of pure salt. A measured value and a target appropriate to your equipment are necessary; the calculator does not choose those for you.
Is 3,200 ppm the right target for every saltwater pool?
No. It is an illustrative initial input. Hayward's AquaRite revision G manual gives that equipment its own salt target and operating range, but those values must not be generalized to every chlorinator or installation. Enter the target in your equipment guidance and verify existing salinity before using any mass estimate. Salt level alone does not establish overall water balance or sanitation.
Should I add all the whole bags shown in the result?
Not necessarily. The bag count is rounded up for purchasing, while the addition uses the unrounded product mass. If a calculation needs 42 kg and bags contain 25 kg, two bags provide 50 kg but 8 kg is left outside the calculated addition. The result separates those quantities. Confirm measurements and product instructions; the planner does not replace handling or retesting guidance.
What happens if my measured salt is already at or above the target?
At the selected target, the modeled addition and purchase count are zero. Above the target, no positive salt addition can lower concentration, so the result explicitly says no addition is calculated and keeps the measured concentration unchanged. It does not display a negative dose or provide a draining or dilution procedure. Recheck the measurement and applicable equipment guidance.
How does product purity change the estimate?
The product mass is the required pure-salt mass divided by the labelled purity fraction. For example, 99.5% is a fraction of 0.995. The accepted 90–100% numerical range is only a model limit, not a recommendation that a 90%-pure product is suitable. Hayward's cited AquaRite manual specifies greater-than-99% sodium chloride for that equipment; use the approved product and instructions for your own system.
How accurate are geometry-based pool volumes?
They are approximations based on the water actually present. The rectangle, circle and elliptical oval models assume vertical sides and a constant horizontal footprint, multiplied by average water depth. For a rectangular pool with a single linear floor slope, the mean of shallow and deep water depths is the appropriate average. Irregular floors, steps and curved walls are not resolved by these simple shapes. A measured volume is preferable when those assumptions do not fit.
What does measurement sensitivity tell me?
It explores four combinations of your chosen volume and measured-salinity ranges. One output recalculates the product required for each scenario; another holds the nominal addition fixed and shows the resulting concentrations. This exposes how an overestimated volume or inaccurate test can miss the target. The ranges are user assumptions, not statistical confidence intervals or claims about a test instrument. Setting both variations to zero repeats the nominal scenario.
Why are ppm and mg/L treated as equal, and how are units rounded?
For dilute water this planner approximates 1 ppm as 1 mg/L and ignores density changes and displacement. It is a practical mass-balance convention, not an exact solution-density model. US gallons use 3.785411784 L, pounds use 0.45359237 kg and feet use 0.3048 m. Unit switches retain canonical quantities; exact decimal rational arithmetic avoids rounding a genuinely just-over-bag mass down. Geometry uses floating-point arithmetic and an approximation to pi. Displayed figures are rounded, while CSV retains unrounded numeric results.
Similar Calculators
Serial Dilution Calculator
Plan serial dilutions by factor, target concentration or transfer volume. Keep the volume you need at every stage, inspect material balances and export the series.
Tank Volume & Dip Chart Calculator
Find tank volume from liquid depth or solve depth from volume. Compare fill levels and export dip charts for horizontal cylinders, upright cylinders and boxes.
Unit Converter
Convert between units of length, weight, volume, and area — all in one tool.
Gallons to Liters Calculator
Convert gallons (us) to liters instantly with a clean, one-field converter.
Pounds to Kilograms Calculator
Convert pounds to kilograms instantly with a clean, one-field converter.
Pump Curve & Operating Point Planner
Compare pump curves and speeds against system head. Visualize operating flow, runtime, electrical energy and whether your target volume fits the available hours.
