Pipe Pressure Drop Calculator

Compare pipe diameters, friction and fitting losses at one flow. Explore how pressure loss changes as flow rises.

See what pipe size changes.

One flow, up to six pipe sizes. See friction, fitting losses and uncertain flow regimes.

Set the operating point

One shared flow through each candidate. Use a steady, fully filled circular pipe carrying an incompressible Newtonian liquid.

Enter actual inside diameter, not nominal pipe size. Changing diameter units converts all diameters together. If any diameter is unfinished, correct it before converting.

Manage compared pipes · 3 of 6

Optional, up to 60 characters. A blank label uses the pipe number.

Fluid and pipe details

Shared: length 50 m, roughness 0.045 mm, density 998 kg/m³, viscosity 1 mPa·s, ΣK 5.

Use a value appropriate to your liquid and operating conditions.

Dynamic viscosity, not kinematic viscosity. The illustrative defaults are not a temperature lookup.

Sum of entered fitting coefficients, using each candidate's own mean velocity. A fixed ΣK across diameters is an assumption, not automatic fitting selection.

The same entered length, roughness, liquid properties and ΣK apply to every candidate. Open Fluid and pipe details to review or change them.

At the entered flow · Pipe A

Pressure loss · kPa

≈849.936 kPa

Turbulent flow

Velocity
≈5.65884 m/s
Reynolds number
≈141188
Darcy friction factor
≈0.024095
Flow in this result
10 m³/h
Pipe friction contribution
≈770.04 kPa
Fitting contribution (entered ΣK)
≈79.8961 kPa
Friction solver detail
Method
Bracketed Colebrook solution using x = 1/√f.
Residual
8.26006e-13
Iterations
43
Friction factor bracket
0.0240950337223 to 0.0240950337223

Compare diameter losses

Compare diameters at the entered flow

Each row uses the same entered flow and its own pipe velocity. Blue is the entered K contribution; purple is straight-pipe friction. A zero contribution has no width. Unavailable contributions are labeled in the pipe results below.

Pressure loss (kPa)

Numbered horizontal stacked loss bars on one common scale. The buttons below give total and component values and select a pipe. Partial bars contain only known contributions. Tiny components are not enlarged and may overlap visually at this scale.0≈8.5e2123

Explore flow changes

Loss as flow changes

Sampled scenarios run from zero to twice the entered flow. A gap means combined loss is unavailable; it is not interpolated. The operating line remains at the entered flow.

  1. 1. Pipe A · solid · selected
  2. 2. Pipe B · long dash
  3. 3. Pipe C · short dash

Pressure loss (kPa)

Total loss versus flow for numbered pipes, distinguished by line patterns. Separate polylines stop at unavailable samples. A vertical operating marker shows the authored flow. The sampled-flow slider and equivalent table expose values without hovering. Close points and small values may be visually indistinguishable.0≈1.66e3≈3.32e3020

Flow (m³/h) · dashed vertical line: operating flow

Arrow keys move between samples. Spacing is not uniform near regime boundaries. This inspector does not change the entered operating flow.

Flow: 10 m³/h · turbulent · operating point

The curve is a bounded sampled scenario, not a continuous accuracy guarantee. Regime and correlation-limit neighborhoods have extra samples.

Unknown combined-loss samples split the curve. Zero straight length can retain a known K-only total through those regions.

Curves connect sampled known values only. Read the inspector and table for small or overlapping values; no small loss is enlarged.

Inspecting the entered operating point

Pipe A. This inspection does not change the flow input above.

≈849.936 kPa

Turbulent flow

Velocity
≈5.65884 m/s
Reynolds number
≈141188
Darcy friction factor
≈0.024095
Flow in this result
10 m³/h
Pipe friction contribution
≈770.04 kPa
Fitting contribution (entered ΣK)
≈79.8961 kPa
Friction solver detail
Method
Bracketed Colebrook solution using x = 1/√f.
Residual
8.26006e-13
Iterations
43
Friction factor bracket
0.0240950337223 to 0.0240950337223
Complete pipe comparison ledger

All rows use the entered operating flow. Unknown losses remain unavailable. This comparison does not select a suitable installation size.

Pipe comparison ledger
PipeInside diameterVelocityReynolds numberRegimeDarcy fPipe lossFitting lossCombined loss
25 mm≈5.65884 m/s≈141188Turbulent flow≈0.024095≈770.04 kPa≈79.8961 kPa≈849.936 kPa
40 mm≈2.21049 m/s≈88242.6Turbulent flow≈0.0228483≈69.6369 kPa≈12.1912 kPa≈81.8281 kPa
50 mm≈1.41471 m/s≈70594.1Turbulent flow≈0.0226892≈22.6598 kPa≈4.99351 kPa≈27.6533 kPa
Save or import pipe inputs

Complete report

Save every operating result and sampled flow, with units, original inputs, assumptions, unavailable reasons and solver details. Curve points use spreadsheet-friendly numeric columns.

Complete report CSV
Convention and limits

This is frictional loss for an entered, fully filled circular liquid pipe. It does not include static elevation or establish pump duty, equipment suitability, cavitation, water hammer or installation compliance.

Darcy friction uses the laminar formula below Reynolds number 2,000 and implicit Colebrook above 4,000. The transition interval and numerical neighborhoods of its boundaries remain uncertain. Turbulent Colebrook is bounded to relative roughness at most 0.05 and Reynolds number at most 10¹².

Unknown friction does not erase a known fitting contribution. Zero pipe length gives zero pipe-friction loss; zero flow gives zero losses with an unavailable friction factor. A shared ΣK is an explicit comparison assumption, not a universal fitting law.

  • Steady, fully developed flow of an incompressible Newtonian liquid in a full circular pipe; properties are entered constants.
  • Darcy friction factor: 64/Re below 2000; Colebrook above 4000 within Re <= 1e12 and roughness/diameter <= 0.05. Transition and numerical boundary neighborhoods remain unavailable.
  • The entered sum K is referenced to each candidate's own velocity and is held constant across flow scenarios. This is not a universal low-Re fitting correlation.
  • Conventional gravity is 9.80665 m/s2. No static head, pump selection, gas flow, network balance, cavitation or water-hammer analysis is included.
  • Primary methods: Hydraulic Institute https://datatool.pumps.org/fluid-flow-iii/general and https://datatool.pumps.org/fluid-flow-iii/fr-loss-water. Results are descriptive, not installation or safety approval.

Displayed physical estimates are rounded and marked with ≈. Small nonzero chart components may be hard to distinguish; use the ledger and complete report for their values.

How to use this calculator

  1. Enter Flow rate and choose Flow unit. Select a pipe, edit its Pipe label and Inside diameter, and choose Inside diameter unit. Use actual clear inside dimensions rather than nominal pipe trade size. Compare up to six separate candidates.
  2. Review Pipe length, Absolute roughness, Fluid density (kg/m³), Dynamic viscosity (mPa·s) and Fitting coefficient ΣK in the shared details. These are your assumptions; the examples do not look up a material or fluid temperature. Shared K is applied to each candidate's own velocity.
  3. Read the selected pipe's result at the entered flow: pipe and fitting pressure loss, combined loss, loss head, velocity, Reynolds number and Darcy friction factor. A transition or correlation warning can leave the total unavailable while retaining known quantities.
  4. Compare the common-scale loss components and loss-versus-flow curves. Select another pipe or inspect a sampled flow to see its values. The sample inspector does not change the entered operating flow. A gap means an unavailable total; a small-detail notice does not make a tiny component exactly zero.
  5. Change a unit only when the affected drafts are valid. Conversion preserves the underlying quantity and restores original source text on a round trip. For an imported unknown unit, explicitly declare the intended unit; this retains the numbers without conversion and requires your review.
  6. Use Input format and Input text to preview to stage a complete CSV or TSV plan, then apply it explicitly. Reusable input preserves unfinished drafts. Export a complete result report after correcting malformed inputs; legitimate transition and correlation limits remain explicit reportable statuses.

The Formula

The mathematical logic powering this calculation is:

For volumetric flow Q, inside diameter D, length L, absolute roughness ε, density ρ, dynamic viscosity μ and entered fitting coefficient K: velocity v = 4Q/(πD²), Reynolds number Re = ρvD/μ, pipe pressure loss Δp_pipe = f(L/D)ρv²/2, fitting loss Δp_K = Kρv²/2, and total loss Δp = Δp_pipe + Δp_K. Loss head h = Δp/(ρg), with conventional g = 9.80665 m/s². The factor f is Darcy, not Fanning.
At positive laminar flow, f = 64/Re and pipe loss is evaluated as 128μLQ/(πD⁴). Turbulent f solves 1/√f = −2log10[ε/(3.7D) + 2.51/(Re√f)]. The declared Hydraulic Institute policy uses Re below 2,000 as laminar, above 4,000 as turbulent, and 2,000–4,000 as unresolved transition. A small declared numerical band around each boundary remains uncertain rather than being assigned a regime from rounded text.
Colebrook is limited here to ε/D ≤ 0.05 and Re ≤ 10¹². Outside that range, or in transition, the entered K loss remains available; positive-length pipe loss and total remain unavailable. Zero length makes pipe loss zero independently of f. Zero flow makes all losses zero while f is unavailable. An unavailable factor is never replaced by zero.
Each diameter is a separate hypothetical uniform pipe with the same shared inputs. The K assumption uses each pipe's own velocity; it is not a series network or automatic fitting redesign. The 0–2Q curves contain bounded derived scenarios, including regime markers, and leave gaps wherever total loss is unknown. Numerical results are approximations conditional on steady, fully developed, incompressible Newtonian flow and constant entered properties.

Worked Example

If you input:

  • Flow rate: 10 m³/h
  • Pipe length: 50 m
  • Absolute roughness: 0.045 mm
  • Fluid density (kg/m³): 998
  • Dynamic viscosity (mPa·s): 1
  • Fitting coefficient ΣK: 5
  • Inside diameter — Pipe A / Pipe B / Pipe C: 25 / 40 / 50 mm

Result:

For these illustrative shared inputs, all three operating points are turbulent. Total pressure loss is approximately 849.936123 kPa for Pipe A (25 mm), 81.828083 kPa for Pipe B (40 mm), and 27.653296 kPa for Pipe C (50 mm). Their loss heads are approximately 86.843051, 8.360864 and 2.825502 m. Each result describes a separate pipe at 10 m³/h; the candidates are not joined in series, and the shared K assumption does not automatically select suitable fittings.

Frequently Asked Questions

Does this calculate pump discharge pressure or choose a pipe size?

It compares dissipative pipe and fitting loss for separate hypothetical uniform pipes at the same volumetric flow. It does not include elevation, a pump curve, cavitation, pipe networks or a required delivery pressure. No diameter is labeled safe or optimal. Use the comparison to understand the consequences of your entered dimensions and assumptions; a loss calculation alone does not establish installation suitability.

Why is there a gap between laminar and turbulent results?

This tool explicitly adopts the Hydraulic Institute's approximate 2,000–4,000 Reynolds transition convention. It does not interpolate a confident friction factor through that band. A narrow numerical resolution band around its boundaries is also left uncertain. These are stated modeling policies, not exact universal physical thresholds. Known velocity, Reynolds number and the entered fitting contribution remain visible even when pipe loss is unresolved.

What does the shared fitting coefficient mean when diameters change?

The same entered sum K is used for every candidate, referenced to that candidate's mean velocity. This is a controlled assumption, not a claim that a real collection of fittings keeps the same coefficient at every size, configuration or flow condition. The workspace does not select fittings or provide measured coefficient tables. Treat K-based laminar losses with the same caution: the entered constant is not a general low-Reynolds fitting law.

How are zero flow, zero length and an unknown friction factor different?

At zero flow, velocity, Reynolds number and all pressure/head losses are zero, but the friction factor is unavailable rather than zero. With zero length and positive flow, pipe loss is exactly zero and total equals the known fitting loss even when f is unknown. For positive length, an unknown f leaves pipe loss and total unavailable. Setting K to zero removes fitting loss only; it cannot resolve an unknown pipe contribution.

Are the default density, viscosity and roughness measured material properties?

No. Defaults and presets are illustrative editable values. The calculator does not infer fluid composition, temperature, pipe age, lining or roughness from a material name. Its model assumes a steady, fully developed, fully filled circular pipe, an incompressible Newtonian liquid and constant properties. Passing the computational bounds does not validate those physical assumptions, particularly at extreme flow or diameter choices.

What are the input and correlation limits?

Compare 1–6 pipes. Canonical limits are flow 0–100,000 m³/h, inside diameter 1–10,000 mm, length 0–100,000 m, roughness 0–50 mm, density 1–20,000 kg/m³, viscosity 0.001–100,000 mPa·s and sum K 0–100,000. Authored numbers allow up to 12 significant digits and six effective decimal places. Turbulent Colebrook results additionally require relative roughness at most 0.05 and Reynolds number at most 10¹². A limit is reported explicitly, not silently capped.

Can I retain invalid drafts, convert units and reuse the complete plan?

Yes. Structurally valid reusable input preserves unfinished numeric drafts and recognized unit-conversion anchors. A malformed diameter keeps valid peers visible but blocks a complete result report; a shared error blocks dependent calculations. A refused unit conversion leaves the affected unit and all drafts unchanged. Unknown imported units require an explicit declaration without conversion. Complete result CSV is a report, while reusable CSV or TSV input is the separate format for restoring the plan.

Similar Calculators