Water Softener Capacity & Regeneration Planner

Compare up to six rated water-softener operating settings against a repeating seven-day water-use profile. Inspect capacity depletion, regeneration causes and discarded usable capacity, then compare salt, regeneration water and costs across your chosen horizon. Enter matched capacity and regeneration resource data from the operating setting you are considering. The daily planning policy is explicit and does not emulate a manufacturer controller or establish treatment suitability.

Water-softener planning

See when capacity runs out

Compare rated settings, daily demand and regeneration overrides—then see the salt, water and cost behind each schedule.

Examples are hypothetical rated operating points. Capacity, salt dose and regeneration water belong to the same setting; use matched manufacturer data.

Compare resources over 30 days

Initial fresh charge is excluded. There is no final regeneration after the horizon. Lower cost alone does not establish product suitability.

Supported settings and exact modeled horizon totals
SettingUsable grainsRegenerationsSalt (lb)Regeneration water (US gal)Cost (USD)Discarded usable grains
180003181205.10
270002201005.52000

Capacity through the day · Lower-dose setting

Vertical dashed jumps restore capacity before use; solid slopes consume that day's demand. Diamonds mark regeneration. The ledger retains exact values for events too close to distinguish.

18000 usable grains at top0 grains at bottom
Available capacity for Lower-dose setting over 30 days; 3 regenerations. Daily quantities are in the ledger.
Before day 1End of day 30

Day 1 · profile day 1

200 US gal uses 2000 grains. Opening: 18000; available after any regeneration: 18000; closing: 16000 grains.

No regeneration. Elapsed age after use: 1 days.

Complete daily ledger
Exact daily capacity in grains; service volume in US gallons
DayService (US gal)Demand (grains)OpeningTriggerDiscardedAvailableClosingAge (days)
200200018000None018000160001
200200016000None016000140002
200200014000None014000120003
200200012000None012000100004
200200010000None01000080005
20020008000None0800060006
20020006000None0600040007
20020004000None0400020008
20020002000None0200009
20020000capacity018000160001
200200016000None016000140002
200200014000None014000120003
200200012000None012000100004
200200010000None01000080005
20020008000None0800060006
20020006000None0600040007
20020004000None0400020008
20020002000None0200009
20020000capacity018000160001
200200016000None016000140002
200200014000None014000120003
200200012000None012000100004
200200010000None01000080005
20020008000None0800060006
20020006000None0600040007
20020004000None0400020008
20020002000None0200009
20020000capacity018000160001
200200016000None016000140002
200200014000None014000120003

Keep the complete comparison

What this schedule assumes

One regeneration at most, before each day's use, with a fresh starting charge. An entered reserve reduces usable capacity; a day exceeding that capacity is unsupported. Timer overrides may regenerate on zero-use days. Regeneration water is not added to softened service demand. This is a planning comparison, not a brand controller simulation, peak-flow check, treatment recommendation or product certification. Costs omit installation, maintenance, electricity and taxes.

How to use this calculator

  1. Choose Steady household example or Weekend demand example, then open Edit water use and settings. Both examples are hypothetical.
  2. Enter Measured hardness in grains per US gallon, Planning horizon and seven daily softened-water volumes. Include only water that passes through the softener; profile day 1 is your chosen start, not an inferred weekday.
  3. Enter currency and salt/water prices. For each Rated operating setting, enter matched rated capacity, salt dose and regeneration water, plus your planning reserve and optional maximum elapsed days. Add or copy up to six settings.
  4. Select Update comparison. Read horizon totals and any unsupported setting. Select a setting to inspect its capacity chart, regeneration events and discarded usable capacity.
  5. Use Inspect day or the complete daily ledger to see opening, restored and closing capacity. Download softener CSV or use its selectable copy to retain exact inputs and results.

The Formula

The mathematical logic powering this calculation is:

Daily hardness demand D = softened service gallons × hardness in grains per US gallon. Usable capacity U = rated grains × (1 − reserve percent/100). The repeating seven-day profile starts at day 1 and continues for the entered 1–366-day horizon. Each setting begins with a fresh charge and elapsed age zero. Before daily use, regenerate if D exceeds remaining usable capacity or a nonzero maximum-days override has been reached. Record capacity, timer or both; discard remaining usable capacity, restore U and reset age. Consume D and increment age. Exact equality consumes capacity without triggering regeneration that day. No initial preparation or post-horizon regeneration is charged.
If any modeled day demands more than U, that setting is unsupported; no partial-horizon totals are shown. Other settings still calculate. This once-before-day policy is a declared planning assumption, not immediate/delayed controller emulation. A timer may regenerate on a zero-use day. Regeneration water is an external resource cost, not additional service demand.
Salt = regeneration count × entered pounds per regeneration. Regeneration water = count × entered gallons per regeneration. Operating cost = salt × price per lb + regeneration water × water/sewer price per 1,000 US gallons / 1,000. Total available charges = (count + 1) × U = total removed demand + discarded usable capacity + final remaining capacity. Exact rational arithmetic controls all boundaries and totals; approximate display values are marked.
Bounds: hardness 0–200 grains/US gal; each daily volume 0–100,000 US gal; rated capacity positive through 1,000,000 grains; reserve 0–99%; salt 0–1,000 lb/event; regeneration water 0–10,000 US gal/event; prices 0–10,000. These quantities accept up to four decimals. Maximum elapsed days is a whole number 0–365; zero disables it. Compare one to six settings with names up to 80 characters and a three-letter uppercase currency label.
No iron compensation, peak-flow capacity, pressure drop, water safety, installation suitability, controller settings, wastewater compliance or certification is inferred. Capacity and salt dose are paired inputs, not an inferred performance curve. Installation, maintenance, electricity and taxes are excluded.

Worked Example

If you input:

  • Demand: 200 US gal/day at 10 grains/US gal for 30 days.
  • Settings: 20,000 grains at 6 lb salt / 40 US gal per regeneration; 30,000 grains at 10 lb / 50 US gal. Both with 10% reserve and no timer override.
  • Prices: USD 0.25/lb salt and USD 5 per 1,000 US gal regeneration water.

Result:

Daily demand is 2,000 grains. The lower-dose setting has 18,000 usable grains, regenerates on days 10, 19 and 28, and uses 18 lb salt plus 120 US gal water for USD 5.10. The larger setting has 27,000 usable grains, regenerates on days 14 and 27, and uses 20 lb salt plus 100 US gal water for USD 5.50. Less frequent regeneration does not necessarily mean lower operating cost.

Frequently Asked Questions

Does this choose a safe or certified softener size?

No. It compares entered operating points against a declared daily demand schedule. Peak service flow, pressure drop, water quality, product certification and installation requirements must be checked separately.

Why enter capacity and salt together?

A rated capacity belongs to a specified regeneration dose and operating conditions. A nominal marketing capacity is not necessarily the capacity at your intended dose. The calculator never infers a capacity curve from salt weight.

How does reserve affect the schedule?

Reserve reduces the capacity available to the modeled service cycle. For example, 20,000 grains with 10% reserve gives 18,000 usable grains. The selected percentage is your planning assumption, not a recommended controller setting.

When does regeneration occur?

At most once before daily use, when demand exceeds remaining usable capacity or the entered maximum-day override is reached. The fresh initial charge is not billed. Consuming exactly the remaining capacity does not add an event until a later day requires it.

Why is a setting unsupported?

At least one modeled day needs more hardness-removal capacity than one usable charge provides. The planner does not simulate multiple daily regenerations or silently bypass some demand. It reports the first such day without partial totals.

Why can a timer increase salt and water use?

A timer can discard remaining usable capacity before the demand would require regeneration. It may also trigger on days with zero water use. The discarded-capacity total and event causes make this visible.

Are these annual operating costs?

They cover only the exact entered horizon, including partial final weeks. A 30-day total is not labeled an annual total. Salt and regeneration water are included; maintenance, installation, electricity and taxes are not.

Does WaterSense label water softeners?

EPA’s guidance reviewed November 12, 2026 says WaterSense does not label water softeners. This planner does not claim that an entered setting earns a label or meets NSF/ANSI 44 certification.

Similar Calculators