Snow Load Calculator & Water Equivalent Planner
Estimate the weight of entered snow and retained water across distinct horizontal roof areas. Compare two sets of observations or scenarios in the zone chart. A high local load can occur alongside a much lower whole-area average, especially where wet or layered snow is concentrated.
Compare snow and retained water by zone
Compare two water-equivalent estimates using the same horizontal roof areas.
Comparison settings
Use available measurements and a separate comparison value you have established. The worksheet gives estimated local and combined static loads.
Horizontal roof zones
Each area is one disjoint section of the horizontal plan. Open its snow assumptions to compare the two scenarios.
Edit snow assumptions for Drift band
Density is a percentage of liquid water density.
Scenario A exceeds the entered line at the high bound in 1 zone. Scenario B has no high bound above the entered line.
850 ft² of total horizontal area.
Scenario A
8.4026–12.1833 psf
Area-weighted pressure
- Combined weight
- 7,142.2–10,355.8 lb
- Highest zone high bound
- 31.668 psf
Highest zone Drift band
Scenario B
10.4459–12.1894 psf
Area-weighted pressure
- Combined weight
- 8,879–10,361 lb
- Highest zone high bound
- 24.18 psf
Highest zone Drift band
Local pressure by horizontal zone
The circle marks the low bound. The diamond marks the high bound. Every row uses the same pressure scale.
Below the comparison line
Below the comparison line
Range crosses the comparison line
Below the comparison line
Water equivalent and load ledger
Open snow load ledger
Positive margin means the high bound is below the entered line. Negative margin expresses the amount above it as equivalent inches of water.
| Zone | Scenario | Water equivalent | Pressure | Weight | High-bound water margin |
|---|---|---|---|---|---|
| Main face | Scenario A | 1.06–1.54 in | 5.512–8.008 psf | 3,858.4–5,605.6 lb | 3.2677 in |
| Main face | Scenario B | 1.55–1.85 in | 8.06–9.62 psf | 5,642–6,734 lb | 2.9577 in |
| Drift band | Scenario A | 4.21–6.09 in | 21.892–31.668 psf | 3,283.8–4,750.2 lb | −1.2823 in |
| Drift band | Scenario B | 4.15–4.65 in | 21.58–24.18 psf | 3,237–3,627 lb | 0.1577 in |
Show selectable CSV
How to use this calculator
- Enter the names and horizontal areas of two to eight disjoint roof zones.
- Open each zone and select Direct water or Snow layers for each scenario. Enter the water-equivalent endpoints, or the vertical depths and density bounds.
- Enter separately retained liquid in inches of water equivalent when it is absent from the snow input. Use zero if none is modeled.
- Enable the comparison line if you have an established load value to compare. Inspect both ends of each zone interval and the area-weighted total.
- Open the zone ledger and download the CSV to retain all authored inputs and calculated boundaries.
The Formula
The mathematical logic powering this calculation is:
Snow water equivalent is the depth of liquid water in an entered snow column. Use two bounds from prepared observations, or compute each layer as its vertical snow depth times its fraction of water density. A 12-inch layer at 8–12% of water density gives 0.96–1.44 inches of water equivalent. Sum the layers to form the lower and upper water-equivalent endpoints.
Add any separately entered retained liquid to both bounds. Include it only if it is missing from the entered snow water equivalent. Multiply by 5.2 psf per inch of water equivalent for an approximate static pressure on the horizontal area, using the NWS conversion. Multiply each zonal pressure by its disjoint horizontal area to estimate the weight in pounds. Add the low or high weights across all zones, then divide by total horizontal area for the corresponding area-weighted pressures. The two endpoints combine all entered low or all entered high values. They are scenario bounds without a modeled probability.
The chart compares each zone's two pressure ranges against the optional number you enter. A range crosses the line if its low is at or below the reference and its high is above. A high bound equal to the line is shown separately. The signed high-bound margin in inches of water equivalent equals the difference between the chosen line and the high pressure, divided by 5.2.
Use two to eight disjoint horizontal areas, each 0.0001–1,000,000 ft², with one to three snow layers per calculation when selected. Vertical snow depths support 0–360 in, density 0–100% of water, and direct water-equivalent and retained liquid amounts each 0–120 in. The optional comparison line accepts 0–10,000 psf. Each amount accepts up to four decimal places. Provide measurements or scenario assumptions that are already available. The result estimates the entered static load only. It does not determine building-code load, drift geometry, roof capacity, structural demand on particular members, or a safe operating condition.Worked Example
If you input:
- Horizontal roof zones (ft²): 700 main face, 150 drift band
- Scenario A: Main face 12 in at 8–12% plus 0.1 in retained. Drift 21 in at 16–24% plus 2 in at 30–40% and 0.25 in retained.
- Scenario B: Main 1.2–1.5 in and drift 3.8–4.3 in direct water equivalent. Add 0.35 in retained in each zone.
- Comparison line (psf): 25 as an illustration
Result:
Scenario A's drift band contains 4.21–6.09 in of modeled water equivalent and gives 21.892–31.668 psf. The 31.668 psf local high exceeds the entered 25 psf line while the area-weighted high is 12.1833 psf. Scenario B's drift high is 24.18 psf. Its area-weighted high is 12.1894 psf, illustrating how similar averages can hide different local concentrations.
Frequently Asked Questions
What is snow water equivalent?
It is the depth of liquid water in the snow column. Two snowpacks that are the same depth can have different water equivalents because their density differs.
Which roof area belongs here?
Use the horizontal plan footprint of each non-overlapping section. The vertical-depth model applies weight per square foot of that projected area. Start with an already prepared measurement or plan.
How do I enter ice or retained liquid?
Represent layers through the stated relative water density, or use direct total water equivalent. Add separate retained liquid only when it was excluded from the preceding inputs.
Why can the zone high exceed the reference while the average stays below it?
The whole-area pressure divides total weight by the combined area. A narrower zone can carry a larger estimated pressure. The interval chart keeps that local difference visible.
Should I take the modeled high as my roof's design load?
The modeled values describe the inputs you enter. A building's required design loads and structural capacity require separate, site-specific determination.
What does equality with the comparison line mean?
The arithmetic high bound is exactly the entered pressure before displayed rounding. A further positive amount of retained liquid would put that high bound above the same comparison line.
Similar Calculators
Rafter Span Bending & Deflection Planner
Compare two rafters at a measured horizontal span. See how documented roof loads, spacing, bending values and stiffness affect their modeled limits.
Roof Area Calculator
Plan shed, gable and hip roof area, faces and edges. Compare roofing, underlayment, starter and cap quantities with exact whole-pack purchasing, diagrams and CSV.
Roof Replacement Cost & Quote Comparison Calculator
Compare roof replacement quotes, scope gaps and decking repair allowances. See when prices cross, how many repairs fit your budget, and export the full comparison.
Gutter Installation Cost & Fall Planner
Compare gutter installation estimates, section and hanger quantities, and single or split fall profiles with exact drop headroom, cost breakdowns and CSV.
