Sheet Metal Bend Allowance & Coupon Planner

Compare two single-bend sheet metal sections with different radii, thicknesses and neutral-axis inputs. Enter outside flange lengths to the virtual apex or the straight lengths to the tangencies. Draw the formed profiles and see how each straight segment and the bend allowance contribute to the flat blank. Use a coupon with a known flat length to infer an effective K-factor and examine the effect of measured length tolerance.

Single-bend geometry

Compare sheet metal bends and flat lengths

Use outside flange or straight tangent measurements. Predict a blank from K or infer K from a measured coupon.

Sheet metal flat length comparison

Option A · 90° bend · 3 mm inside radius

80.969 mm flat length

5.969 mm bend allowance · K 0.4

Option B · 90° bend · 5 mm inside radius

80.1106 mm flat length

9.1106 mm bend allowance · K 0.4

Option B needs 0.8584 mm less flat length.

Edit bend measurements

Outside flange lengths run from the edge to the virtual apex. Tangent lengths stop where the curve begins. Each basis keeps its own saved flange measurements.

Option A
Option B

Formed bend cross-sections

Views share one scale. The purple dashed line is the neutral axis. Dots mark its tangency points. Fine dashed lines extend the flanges to their virtual apex when that basis is entered.

Option A

Option A formed bend profile90° bend, 3 mm inside radius, 2 mm thickness and 3.8 mm neutral radius.

3 mm inner radius · 3.8 mm neutral radius · 90° inside opening

Option B

Option B formed bend profile90° bend, 5 mm inside radius, 2 mm thickness and 5.8 mm neutral radius.

5 mm inner radius · 5.8 mm neutral radius · 90° inside opening

Flat lengths by segment

Option A · 80.969 mm

Tangent A
45 mm
Bend allowance
5.969 mm
Tangent B
30 mm

Option B · 80.1106 mm

Tangent A
43 mm
Bend allowance
9.1106 mm
Tangent B
28 mm
Show flat length reconciliation

Option A

Outside lengths to virtual apex

Tangent A
45 mm
Neutral arc allowance
5.969 mm
Tangent B
30 mm
Flat via tangent lengths
80.969 mm
Outside setback
5 mm
Outside flange A
50 mm
Outside flange B
35 mm
Bend deduction
4.031 mm
Flat via outside lengths
80.969 mm

Option B

Outside lengths to virtual apex

Tangent A
43 mm
Neutral arc allowance
9.1106 mm
Tangent B
28 mm
Flat via tangent lengths
80.1106 mm
Outside setback
7 mm
Outside flange A
50 mm
Outside flange B
35 mm
Bend deduction
4.8894 mm
Flat via outside lengths
80.1106 mm

Export the comparison

Show CSV text

How to use this calculator

  1. Choose outside lengths to the virtual apex or straight tangent lengths and measure both flanges in that basis.
  2. Enter bend rotation or included opening, as well as the actual inside radius and thickness. Switching angle convention preserves the valid angle.
  3. Enter the K-factor for a flat-length prediction, or switch to Measure a coupon to enter its measured flat and flat-length tolerance.
  4. Compare the formed sections, straight-to-arc breakdown and both calculation bases where supported. Review the coupon K window separately.
  5. Export the entered conventions, solved dimensions and coupon calibration as CSV.

The Formula

The mathematical logic powering this calculation is:

The model is one constant-thickness sheet with a circular bend. Let α be the rotation away from flat, in degrees. The inside opening is 180° − α. For the radian angle θ = α × π/180, thickness T, inside radius R and entered K-factor, the neutral radius is R + KT. Bend allowance BA = θ(R + KT). With straight tangent lengths S₁ and S₂, the modeled flat length is S₁ + BA + S₂.

Outside flange lengths O₁ and O₂ extend to the virtual apex where the two outside flange lines intersect. Through a 90° bend rotation the outside setback is SB = (R + T) tan(θ/2). Each straight tangent length is O − SB. A negative tangent length means the entered outside dimension is too short. Equality gives zero straight length. Bend deduction BD = 2SB − BA and the flat length is also O₁ + O₂ − BD. This signed subtraction convention agrees with the cited source through 90°. Larger rotations up to 150° take straight tangent dimensions only. The worksheet reports their bend allowance and flat length while keeping the outside-apex fields unavailable. Each basis retains its own typed flange dimensions.

In coupon mode the actual flat length is known. Observed allowance is measured flat minus the sum of straight tangents. The effective K estimate is (observed allowance ÷ θ − R) ÷ T. Holding all other measurements fixed, a symmetric flat-length tolerance ±u gives effective K variation ±u ÷ (θT) without clipping. The model accepts a central neutral axis from K = 0 at the inside surface to K = 1 at the outside surface. A central estimate outside this domain remains visible as a diagnostic without a solved bend. At a small angle or with thin stock the same length tolerance can yield a wider K interval.

Angles accept 0.1–150° of bend rotation or the equivalent included openings 30–179.9°. Inside radius supports 0.05–1,000 mm and thickness 0.05–100 mm. Flange lengths support 0–12,000 mm, measured flat coupon lengths 0.001–28,000 mm and flat tolerance 0–10 mm. Enter dimensions to three decimals and K to six decimals. Numerical allowance and trigonometry use floating-point calculations after strict decimal input. The charts represent idealized profiles and flat sections. Tooling, force, springback, actual process yield, minimum producible flanges and material fit are separate considerations.

Worked Example

If you input:

  • Dimension basis: Outside flange lengths to virtual apex, 50 mm and 35 mm
  • Bend rotation and sheet thickness: 90° and 2 mm for both options
  • Neutral axis input: Entered K-factor of 0.4
  • Inside bend radius: 3 mm for Option A and 5 mm for Option B

Result:

Option A has 5 mm outside setback and 45 + 30 mm of straight tangents. The neutral arc allowance is about 5.9690 mm, the bend deduction about 4.0310 mm and the flat length about 80.9690 mm. Option B uses 7 mm setback and 43 + 28 mm of straight tangents. Its allowance is about 9.1106 mm, giving about 80.1106 mm of flat length at the same outside flange sizes.

Frequently Asked Questions

What is the difference between bend allowance and bend deduction?

Bend allowance is the arc distance along the modeled neutral axis. Bend deduction is what you subtract from the sum of the two outside flange lengths in this convention. Through 90°, it is twice the outside setback minus the bend allowance.

Which angle should I enter?

Choose bend rotation for how far the sheet turns from flat, or included opening for the angle between the formed flanges on the inside. A 60° rotation equals a 120° opening. At a right angle both measurements equal 90°.

Where are outside flange lengths measured?

Extend the two outside straight flange faces until their lines meet. Each outside flange length is measured from its edge to that virtual apex. Straight tangent lengths stop at the bend instead. The tool keeps separate drafts for these measurements.

Why does a larger radius sometimes yield a shorter blank?

When the outside flange lengths stay fixed, a larger radius increases bend allowance but shortens both straight tangent sections. When straight tangent lengths stay fixed, increasing radius increases the flat length in this model.

What does the coupon tolerance cover?

It varies only the known flat length by the entered amount and holds the formed angle, flange dimensions, thickness and radius fixed. The result is a sensitivity interval for effective K, with no claims about those other measurements or coupon-to-coupon variation.

What happens if my coupon gives a K-factor below zero or above one?

The worksheet displays the inferred K and diagnostic range. The central result falls outside this model’s neutral-axis interval, so that option does not receive a solved formed cross-section. Check that the coupon’s dimensions and measurement convention describe the same part.

Similar Calculators