Arc Length, Chord & Segment Calculator
Turn circular measurements into an inspectable arc, chord and area calculation. Choose radius with central angle, radius with chord and an explicit arc choice, or chord with sagitta to infer the circle. The explorer pairs the selected arc with its complement around the same circle, showing arc length, sagitta, straight chord, arc-minus-chord excess, sector area and circular-segment area. A proportional geometry diagram distinguishes the curved boundary from the chord and the two different area definitions. Separate length and area sensitivity charts, a 73-point inspector, complete ledgers and downloadable CSV make the geometry reusable. Metric and inch input units share the same page, with exact quantity-preserving changes. This is ideal circular geometry; measured dimensions and real constructed curves can have additional uncertainty.
One chord. Two arcs. See the whole geometry.
Solve from radius and angle, radius and chord, or chord and sagitta—then compare both arcs and their sector and segment areas.
Start with the measurements you know
Positive straight-line distance between the arc endpoints; up to 200000000 mm equivalent.
Positive perpendicular distance from the chord midpoint to the selected arc; it can exceed the radius for a major arc.
Unit changes preserve valid quantities exactly; repeating conversions may appear as fractions. Switching input mode retains unfinished drafts, which are validated when their fields become active.
Minor arc updated. Arc length 20.126925 cm.
Minor arc · selected arc length
20.126925 cm
Shared chord
18.4 cm
Selected sagitta
3.5 cm
Selected segment area
44.151556 cm²
Classification follows the supplied geometry. Displayed angles are rounded; a near-limit arc can display 180° or 360° while retaining a distinct small complement below.
The other arc on the same circle
Complementary arc length
66.841335 cm
Major arc · 276.68578°
Solved radius
13.841429 cm
Center-to-chord distance
10.341429 cm
The two arc lengths add to 86.968261 cm. Their segment areas add to the full circle area, 601.88248 cm². Small complementary values are calculated directly.
See the arc, chord and sagitta
- Solid blue: inspected arc
- Dashed gold: shared chord
- Solid green: sagitta
- Dotted purple: radii
A segment lies between the arc and its chord. A sector lies between the arc and the circle center. The minor segment is sector minus triangle; the major segment is sector plus the unsigned triangle.
| Measurement | Selected arc | Complementary arc |
|---|---|---|
| Classification | Minor arc | Major arc |
| Central angle | 83.314223° (1.4541075 rad) | 276.68578° (4.8290778 rad) |
| Arc length | 20.126925 cm | 66.841335 cm |
| Sagitta | 3.5 cm | 24.182857 cm |
| Arc length minus chord | 1.7269252 cm | 48.441335 cm |
| Sector area | 139.2927 cm² | 462.58978 cm² |
| Segment area | 44.151556 cm² | 557.73093 cm² |
| Triangle area (unsigned) | 95.141143 cm² | 95.141143 cm² |
What changes as the angle grows?
This sweep keeps the solved radius fixed and varies the central angle from 0° to 360° in 5° steps. It illustrates the circle independently of your exact selected arc.
- Arc length · solid blue
- Chord length · dashed purple
- Sagitta · dotted teal
At 90°
- Arc length
- 21.742065 cm
- Chord length
- 19.574736 cm
- Sagitta
- 4.0540606 cm
- Sector area
- 150.47062 cm²
- Segment area
- 54.678048 cm²
All 73 sweep measurements
| Angle (°) | Arc length | Chord length | Sagitta | Sector area | Segment area |
|---|---|---|---|---|---|
| 0 | 0 cm | 0 cm | 0 cm | 0 cm² | 0 cm² |
| 5 | 1.2078925 cm | 1.2075093 cm | 0.013173973 cm | 8.3594789 cm² | 0.010606139 cm² |
| 10 | 2.415785 cm | 2.41272 cm | 0.052670815 cm | 16.718958 cm² | 0.084752242 cm² |
| 15 | 3.6236775 cm | 3.6133379 cm | 0.11841534 cm | 25.078437 cm² | 0.28549469 cm² |
| 20 | 4.83157 cm | 4.8070777 cm | 0.2102824 cm | 33.437916 cm² | 0.67492641 cm² |
| 25 | 6.0394625 cm | 5.9916669 cm | 0.32809712 cm | 41.797395 cm² | 1.3137042 cm² |
| 30 | 7.2473551 cm | 7.1648507 cm | 0.47163524 cm | 50.156874 cm² | 2.2605874 cm² |
| 35 | 8.4552476 cm | 8.3243957 cm | 0.64062352 cm | 58.516353 cm² | 3.5719903 cm² |
| 40 | 9.6631401 cm | 9.4680948 cm | 0.83474028 cm | 66.875832 cm² | 5.3015529 cm² |
| 45 | 10.871033 cm | 10.593771 cm | 1.053616 cm | 75.23531 cm² | 7.4997329 cm² |
| 50 | 12.078925 cm | 11.699281 cm | 1.2968341 cm | 83.594789 cm² | 10.213422 cm² |
| 55 | 13.286818 cm | 12.782521 cm | 1.5639315 cm | 91.954268 cm² | 13.485587 cm² |
| 60 | 14.49471 cm | 13.841429 cm | 1.8543998 cm | 100.31375 cm² | 17.354946 cm² |
| 65 | 15.702603 cm | 14.873988 cm | 2.1676861 cm | 108.67323 cm² | 21.855672 cm² |
| 70 | 16.910495 cm | 15.878235 cm | 2.5031941 cm | 117.03271 cm² | 27.017132 cm² |
| 75 | 18.118388 cm | 16.852256 cm | 2.860285 cm | 125.39218 cm² | 32.863664 cm² |
| 80 | 19.32628 cm | 17.794198 cm | 3.2382791 cm | 133.75166 cm² | 39.414395 cm² |
| 85 | 20.534173 cm | 18.702267 cm | 3.636457 cm | 142.11114 cm² | 46.683089 cm² |
| 90 | 21.742065 cm | 19.574736 cm | 4.0540606 cm | 150.47062 cm² | 54.678048 cm² |
| 95 | 22.949958 cm | 20.409943 cm | 4.490295 cm | 158.8301 cm² | 63.402047 cm² |
| 100 | 24.15785 cm | 21.206299 cm | 4.9443298 cm | 167.18958 cm² | 72.852311 cm² |
| 105 | 25.365743 cm | 21.962287 cm | 5.4153007 cm | 175.54906 cm² | 83.020538 cm² |
| 110 | 26.573635 cm | 22.676469 cm | 5.9023113 cm | 183.90854 cm² | 93.892963 cm² |
| 115 | 27.781528 cm | 23.347485 cm | 6.4044344 cm | 192.26802 cm² | 105.45046 cm² |
| 120 | 28.98942 cm | 23.974058 cm | 6.9207143 cm | 200.62749 cm² | 117.66869 cm² |
| 125 | 30.197313 cm | 24.554994 cm | 7.4501681 cm | 208.98697 cm² | 130.51829 cm² |
| 130 | 31.405205 cm | 25.089189 cm | 7.9917881 cm | 217.34645 cm² | 143.96508 cm² |
| 135 | 32.613098 cm | 25.575625 cm | 8.5445432 cm | 225.70593 cm² | 157.97035 cm² |
| 140 | 33.82099 cm | 26.013377 cm | 9.1073812 cm | 234.06541 cm² | 172.49113 cm² |
| 145 | 35.028883 cm | 26.40161 cm | 9.6792307 cm | 242.42489 cm² | 187.48053 cm² |
| 150 | 36.236775 cm | 26.739587 cm | 10.259003 cm | 250.78437 cm² | 202.88808 cm² |
| 155 | 37.444668 cm | 27.026663 cm | 10.845595 cm | 259.14385 cm² | 218.66016 cm² |
| 160 | 38.65256 cm | 27.262292 cm | 11.43789 cm | 267.50333 cm² | 234.74034 cm² |
| 165 | 39.860453 cm | 27.446026 cm | 12.03476 cm | 275.86281 cm² | 251.06986 cm² |
| 170 | 41.068345 cm | 27.577516 cm | 12.635069 cm | 284.22228 cm² | 267.58808 cm² |
| 175 | 42.276238 cm | 27.656509 cm | 13.237674 cm | 292.58176 cm² | 284.23289 cm² |
| 180 | 43.48413 cm | 27.682857 cm | 13.841429 cm | 300.94124 cm² | 300.94124 cm² |
| 185 | 44.692023 cm | 27.656509 cm | 14.445183 cm | 309.30072 cm² | 317.64959 cm² |
| 190 | 45.899915 cm | 27.577516 cm | 15.047789 cm | 317.6602 cm² | 334.29441 cm² |
| 195 | 47.107808 cm | 27.446026 cm | 15.648098 cm | 326.01968 cm² | 350.81262 cm² |
| 200 | 48.3157 cm | 27.262292 cm | 16.244967 cm | 334.37916 cm² | 367.14215 cm² |
| 205 | 49.523593 cm | 27.026663 cm | 16.837262 cm | 342.73864 cm² | 383.22233 cm² |
| 210 | 50.731485 cm | 26.739587 cm | 17.423854 cm | 351.09812 cm² | 398.9944 cm² |
| 215 | 51.939378 cm | 26.40161 cm | 18.003626 cm | 359.45759 cm² | 414.40196 cm² |
| 220 | 53.14727 cm | 26.013377 cm | 18.575476 cm | 367.81707 cm² | 429.39135 cm² |
| 225 | 54.355163 cm | 25.575625 cm | 19.138314 cm | 376.17655 cm² | 443.91213 cm² |
| 230 | 55.563055 cm | 25.089189 cm | 19.691069 cm | 384.53603 cm² | 457.9174 cm² |
| 235 | 56.770948 cm | 24.554994 cm | 20.232689 cm | 392.89551 cm² | 471.36419 cm² |
| 240 | 57.97884 cm | 23.974058 cm | 20.762143 cm | 401.25499 cm² | 484.21379 cm² |
| 245 | 59.186733 cm | 23.347485 cm | 21.278423 cm | 409.61447 cm² | 496.43202 cm² |
| 250 | 60.394625 cm | 22.676469 cm | 21.780546 cm | 417.97395 cm² | 507.98952 cm² |
| 255 | 61.602518 cm | 21.962287 cm | 22.267556 cm | 426.33343 cm² | 518.86195 cm² |
| 260 | 62.81041 cm | 21.206299 cm | 22.738527 cm | 434.6929 cm² | 529.03017 cm² |
| 265 | 64.018303 cm | 20.409943 cm | 23.192562 cm | 443.05238 cm² | 538.48044 cm² |
| 270 | 65.226195 cm | 19.574736 cm | 23.628797 cm | 451.41186 cm² | 547.20444 cm² |
| 275 | 66.434088 cm | 18.702267 cm | 24.0464 cm | 459.77134 cm² | 555.19939 cm² |
| 280 | 67.64198 cm | 17.794198 cm | 24.444578 cm | 468.13082 cm² | 562.46809 cm² |
| 285 | 68.849873 cm | 16.852256 cm | 24.822572 cm | 476.4903 cm² | 569.01882 cm² |
| 290 | 70.057766 cm | 15.878235 cm | 25.179663 cm | 484.84978 cm² | 574.86535 cm² |
| 295 | 71.265658 cm | 14.873988 cm | 25.515171 cm | 493.20926 cm² | 580.02681 cm² |
| 300 | 72.473551 cm | 13.841429 cm | 25.828457 cm | 501.56874 cm² | 584.52754 cm² |
| 305 | 73.681443 cm | 12.782521 cm | 26.118926 cm | 509.92822 cm² | 588.3969 cm² |
| 310 | 74.889336 cm | 11.699281 cm | 26.386023 cm | 518.28769 cm² | 591.66906 cm² |
| 315 | 76.097228 cm | 10.593771 cm | 26.629241 cm | 526.64717 cm² | 594.38275 cm² |
| 320 | 77.305121 cm | 9.4680948 cm | 26.848117 cm | 535.00665 cm² | 596.58093 cm² |
| 325 | 78.513013 cm | 8.3243957 cm | 27.042234 cm | 543.36613 cm² | 598.31049 cm² |
| 330 | 79.720906 cm | 7.1648507 cm | 27.211222 cm | 551.72561 cm² | 599.6219 cm² |
| 335 | 80.928798 cm | 5.9916669 cm | 27.35476 cm | 560.08509 cm² | 600.56878 cm² |
| 340 | 82.136691 cm | 4.8070777 cm | 27.472575 cm | 568.44457 cm² | 601.20756 cm² |
| 345 | 83.344583 cm | 3.6133379 cm | 27.564442 cm | 576.80405 cm² | 601.59699 cm² |
| 350 | 84.552476 cm | 2.41272 cm | 27.630186 cm | 585.16353 cm² | 601.79773 cm² |
| 355 | 85.760368 cm | 1.2075093 cm | 27.669683 cm | 593.523 cm² | 601.87188 cm² |
| 360 | 86.968261 cm | 0 cm | 27.682857 cm | 601.88248 cm² | 601.88248 cm² |
Keep every measurement
Export includes the complete draft, including inactive fields, both arcs, assumptions and all sweep measurements. Diagram and chart choices do not limit the CSV.
Read the geometry with its limits
- One ideal circular arc with a central angle from zero through one complete turn. Radius is not diameter. All active lengths refer to the same circle.
- Radius and angle select one arc. Radius and chord require an explicit minor or major choice, coalescing at the exact diameter. Chord and sagitta select the arc through their exact geometric relationship.
- Sagitta is the perpendicular distance from the chord midpoint to the selected arc. It can exceed the radius for a major arc. Selected and complementary arcs share a chord and together cover one circle.
- The center-to-chord distance is unsigned in shared geometry and signed in each arc record. The triangle area is unsigned: a minor segment is its sector minus the triangle; a major segment is its sector plus the triangle.
- Only fields used by the active input mode determine validity. Inactive drafts remain unchanged in the complete exported input; changing mode can reveal unfinished or invalid entries.
- Exact rational parsing preserves unit conversions, chord feasibility and branch classification. Trigonometry and geometric outputs use floating-point arithmetic; displayed values are rounded to eight significant digits.
- Tiny complementary angles, sagittas, segment areas and arc-minus-chord lengths are calculated directly. A rounded displayed angle at 180 or 360 degrees does not change the exact-input classification.
- The circle diagram preserves proportions. A collapsed flag indicates very small dimensionless chord or sagitta ratios; it does not measure the rendered CSS pixel size or imply that a tiny feature is zero.
- The 73-point sweep varies the angle from zero through 360 degrees at the solved radius. It is a sensitivity illustration and does not change the selected input geometry.
- This is plane circular geometry, without structural design, material allowances, survey certification or calibrated cutting patterns. CSV retains unrounded model values in mm, mm², radians and degrees.
How to use this calculator
- Choose Input mode to match your known measurements: Radius and Central angle (degrees), Radius and Chord length, or Chord length and Sagitta. Inactive values are retained for later mode changes and do not replace the active inputs.
- Enter Radius as half the diameter. Enter Chord length as the straight distance between arc endpoints. For Sagitta, measure perpendicularly from the chord midpoint to the selected arc; this height can be greater than the radius for a major arc.
- In Radius with chord mode, choose Arc choice explicitly. Minor selects the shorter arc and Major the longer arc; both choices become a semicircle when the chord equals the diameter. Correct an infeasible chord rather than expecting the calculator to shorten it.
- Choose each length input’s unit and Display length unit. A valid unit change preserves the quantity exactly and may display a fraction. Central angle remains in degrees, with the calculated radians shown in the result ledger.
- Compare the selected and complementary results and switch the geometry view between them. Inspect the arc, chord and sagitta, then distinguish sector area from circular-segment area. Use the length/area sensitivity views and the 73-point inspector to explore the same radius at different angles.
- Open the full tables or download CSV, including the selectable copy, to retain all inputs, both arc ledgers and every sensitivity point. Use the numeric values for very small features that cannot be resolved in the proportional diagram.
The Formula
The mathematical logic powering this calculation is:
For radius R and selected central angle θ in radians, arc length L = Rθ and sector area = R²θ/2. A sector is bounded by two radii and the arc. A circular segment is bounded by the chord and the arc; its area = R²(θ − sin θ)/2. For a minor arc, this is sector area minus the unsigned radius-chord triangle area. For a major arc, sin θ is negative and segment area is sector area plus that unsigned triangle area. The full circle has circumference 2πR and area πR². This workspace restricts the sweep to one circle, 0–360 degrees.
For Radius with Central angle (degrees), the chord is 2R sin(θ/2), and sagitta is R[1 − cos(θ/2)]. The model evaluates small-side geometry using the smaller of θ and 2π − θ, with exact authored degree complements. It uses 2R sin²(α/4) for the minor sagitta and 2R cos²(α/4) for the major sagitta, where α is the minor central angle. This avoids losing a tiny positive height by subtracting nearly equal values. Empty, semicircle and full-circle endpoints are handled explicitly.
For Radius with Chord length c, require 0 ≤ c ≤ 2R using exact converted quantities. Center-to-chord distance d = sqrt[(R − c/2)(R + c/2)]. Minor angle α = 2 atan2(c/2,d); the major angle is 2π − α. The minor sagitta can be evaluated as (c/2)²/(R + d), and the major sagitta is R + d. A chord shorter than the diameter has two arc choices, including the empty/full alternatives at zero chord. At the exact diameter, the choices coalesce into semicircles. A chord above the diameter is invalid and is never clamped to fit.
For Chord length c with Sagitta s, both must be positive. Radius R = s/2 + c²/(8s), obtained from the right triangle formed by radius, half-chord and center offset. Sagitta is measured perpendicularly from the chord midpoint to the selected arc, so it may exceed the radius. Exact comparison of 2s with c identifies a minor arc when 2s < c, a semicircle when equal, and a major arc when 2s > c. The selected angle can be written 4 atan2(2s,c); the implementation computes the smaller complementary angle directly for major arcs to retain tiny complementary measurements. Derived radius can exceed the editable radius range and is shown without clamping.
The unsigned triangle area is cd/2. Signed center-to-chord offset is positive for the minor/empty side, negative for the major/full side and zero at the semicircle. Minor and major arc lengths sum to the circumference; paired segment areas sum to the circle area. The selected and complementary sagitta values sum to 2R. Arc-minus-chord is L − c and is distinct from either area. For a tiny minor angle, its stable evaluation uses 2R[(α/2) − sin(α/2)].
Small-angle segment area and arc excess can be lost if ordinary floating-point subtraction is used directly. For α ≤ 0.25 radians, the model evaluates α − sin α from its Taylor expansion through the α¹³ term; outside that range it uses direct trigonometry. The series evaluation is an implementation derivation from the sine expansion, rather than a separate empirical formula. Tiny complementary values are calculated on their own minor side and retained even when the displayed major angle rounds to 360 degrees. Exact input comparisons determine the arc class when a displayed angle rounds to 180 degrees.
The sensitivity table contains 73 authored central angles from 0 to 360 degrees in steps of 5 degrees, all using the solved radius. Each point gives arc, chord, sagitta, sector and segment area. The selected and complementary results are calculated independently of those samples and can fall between table angles. Length and area charts use separate units and scales. This sweep varies angle at one fixed radius; it does not represent different measurements or a noncircular curve.
Canonical lengths are mm and areas mm². Exact unit factors are 1 cm = 10 mm and 1 in = 25.4 mm. Valid length-unit switches preserve rational quantities, displaying a fraction when an exact short decimal is unavailable. Trigonometric results remain numerical approximations; display uses eight significant digits and scientific notation for small nonzero quantities. CSV retains unrounded model values and the complete input, including inactive drafts.
Active input bounds: radius 0.000001–100000000 mm equivalent; chord zero or 0.000001–200000000 mm in Radius with chord, and strictly positive in Chord with sagitta; sagitta 0.000001–200000000 mm. Length quantities accept nonnegative plain decimals with at most 12 decimal places or numerator/positive-denominator fractions within the supported text size. Central angle accepts a plain decimal from 0 to 360 degrees with at most 12 decimal places; signs, exponents and fractional angle expressions are unsupported. Only fields required by the chosen input mode are validated; inactive unfinished drafts remain available when switching modes. Display length unit is always required. The explorer excludes noncircular arcs, multiple revolutions, deformation and construction or survey certification.Worked Example
If you input:
- Input mode: Chord length and Sagitta
- Chord length / Sagitta: 18.4 cm / 3.5 cm
- Display length unit: cm
Result:
Using the 18.4 cm chord and 3.5 cm sagitta as ideal dimensions, R = 3.5/2 + 18.4²/(8 × 3.5) = 13.841429 cm. This is a minor arc with central angle 83.314223 degrees and arc length 20.126925 cm. Its sector area is 139.2927 cm², unsigned triangle area is 95.141143 cm² and segment area is 44.151556 cm². The complementary major arc is 66.841335 cm long with sagitta 24.182857 cm and segment area 557.73093 cm². Both arcs share the 18.4 cm chord. Their segment areas add to the circle’s 601.88248 cm². WSDOT rounds the radius to 13.8 in its example; the additional values here are derived mathematical results, with display rounding rather than increased measurement precision.
Frequently Asked Questions
What is the difference between arc length, chord length and sagitta?
Arc length follows the circle’s curved boundary. The chord is the straight line joining its endpoints. Sagitta is the perpendicular distance from the chord midpoint to the chosen arc. Two arcs can share a chord, so a major arc has a larger sagitta than the complementary minor arc. These measurements answer different geometry questions and cannot be substituted for one another.
Why does radius and chord need a minor or major arc choice?
For a chord shorter than the diameter, the endpoints split the circle into a shorter and a longer arc. Radius and chord alone do not say which one you intend. The explicit Arc choice resolves that ambiguity. A diameter gives two equal semicircles. With zero chord, the two endpoint choices are an empty arc and a full circle.
Can sagitta be greater than the radius?
Yes. Sagitta refers to the selected side of the chord. A major arc’s midpoint is farther from the chord than the center is, so its sagitta exceeds the radius. With chord and sagitta entered, the relationship between twice the sagitta and the chord identifies the minor, semicircle or major case. A separate arc choice is unnecessary in that mode.
How are sector area and segment area different?
A sector is the pie-shaped region between two radii and the selected arc. A segment is the region between the straight chord and that arc. For a minor arc, subtract the unsigned triangle area from the sector to obtain the segment. For a major arc, add that triangle area to the major sector. At a semicircle the triangle collapses to zero, so both areas agree.
Why can the result say minor or major while its angle displays 180 degrees?
A very small exact difference from the semicircle can be lost at the chosen display precision, even though the input still determines a side. The class comes from exact input comparisons. Likewise, a major angle can display 360 degrees while its small complementary arc, sagitta or segment remains positive. The complementary ledger retains those small values separately.
Does the sensitivity inspector change my entered geometry?
It explores the solved radius at fixed sample angles from 0 to 360 degrees in 5-degree steps. It does not change the original measurements or force the selected arc onto a sample. The primary selected/complementary results continue to describe the active input, while the table and charts show how the same circle behaves under a different sweep.
Can I mix units or enter a fractional inch measurement?
Length fields accept mm, cm and inches independently, including supported exact fractions such as 3/4. Valid unit changes preserve the physical quantity rather than rounding a converted value behind the scenes. The display unit changes result presentation. Central angle uses plain decimal degrees, so a fractional expression in the angle field is unsupported.
Does the WSDOT example establish survey or construction accuracy?
The default uses WSDOT’s chord and middle-ordinate example as ideal circular dimensions. The radius and the additional arc/area results follow mathematical equations; the extra displayed digits do not improve measurement accuracy. Real curves may depart from a circle, and measurement, construction and instrument errors are outside this model. The diagram is proportional, rather than a calibrated site or cutting drawing.
Similar Calculators
Circle Circumference Calculator
Circle Circumference for the exact fields in this tool, with clear inputs and an immediate result for planning or comparison.
Triangle Calculator
Solve right or oblique triangles from sides and angles. Compare both SSA solutions, inspect scaled geometry, and export sides, angles, area and heights.
Cone & Frustum Capacity Calculator
Compare cone, frustum and cylinder capacity, liquid depth and surface areas. Inspect fill curves, solve target-volume depth and explore ideal sector or rectangle development.
