Thermal Expansion & Clearance Calculator
Enter the opening and insert size at the same reference temperature. Compare both dimensions at the low and high operating temperatures, then inspect the signed clearance at any point in the range. The calculator finds where the gap reaches your target and where the two modeled dimensions become equal. Representative coefficients are available as starting examples.
Thermal expansion and clearance
Track two dimensions as temperature changes and find where the gap reaches a limit.
Dimensions and temperature range
Material examples use representative coefficients. Enter a coefficient appropriate for the material and temperature range in your scenario.
Both parts use the same uniform temperature. Positive gap means clearance. Negative gap is modeled interference.
The minimum gap is met at or below 66.196489067 °C within the entered range.
Clearance across the operating range
The minimum gap is met at or below 66.196489067 °C within the entered range.
- Modeled gap
- Target 0.01 mm
- Zero gap
Dimension and fit ledger
| Point | Temperature | Opening (mm) | Insert (mm) | Gap (mm) | Target check |
|---|---|---|---|---|---|
| Low | -20 °C | 25.012988 | 24.975 | 0.037988 | Meets target |
| Reference | 20 °C | 25.025 | 25 | 0.025 | Meets target |
| High | 120 °C | 25.05503 | 25.0625 | -0.00747 | Below target |
| Inspected | 50 °C | 25.034009 | 25.01875 | 0.015259 | Meets target |
How to use this calculator
- Enter the opening and insert dimensions in millimeters at the same reference temperature. For a circular fit, use the two diameters.
- Enter a linear coefficient in ppm/°C for each part. The material examples fill representative values from OpenStax.
- Enter the low and high operating temperatures and the minimum signed gap. Use zero to check the contact boundary.
- Read the valid part of the interval and inspect any operating temperature on the plot. Compare the original, endpoint and inspected dimensions in the ledger.
- Choose mm or µm for the gap display. Download the clearance CSV for dimensions in millimeters and temperatures in degrees Celsius.
The Formula
The mathematical logic powering this calculation is:
For a reference dimension L₀ in mm, an entered coefficient a in ppm/°C, and a temperature T in °C, L(T) = L₀ × [1 + (a ÷ 1,000,000)(T − T₀)]. An unconstrained opening follows the same linear rule as a solid dimension. Both parts use the same uniform temperature. Opening size and insert size each retain their own coefficient.
Signed gap G(T) equals opening size minus insert size. A positive number represents clearance, zero represents matching nominal dimensions, and a negative number represents modeled overlap. Let G₀ be the gap at the reference temperature and S = (a_opening × L_opening,0 − a_insert × L_insert,0) ÷ 1,000,000 be the gap slope in mm/°C. When S is nonzero, a target g is reached at T = T₀ + (g − G₀)/S. Crossings appear within the entered interval, including its endpoints. If S is zero, the gap is constant and equality holds either throughout or nowhere. The minimum is met where G(T) ≥ g.
The model uses exact integer calculations for endpoint and inspection comparisons. Temperatures and dimensions displayed as numbers are rounded for readability. Enter positive dimensions up to 100,000 mm and a signed target up to ±100,000 mm, with up to six decimals. Enter coefficients from −1,000 to 1,000 ppm/°C and temperatures from −273.15 to 1,500 °C, with up to three decimals. The low temperature must be below the high and both projected endpoint dimensions must be positive.
Use a representative coefficient over the material's actual temperature range. This linear, uniform, free-expansion model leaves out temperature gradients, material changes, combined tolerances, deformation, friction and load. A negative gap represents the overlap of nominal free dimensions. A contact-force or stress calculation requires additional information.Worked Example
If you input:
- At 20 °C: 25.025 mm steel opening and 25.000 mm aluminum insert
- Representative coefficients: 12 ppm/°C for steel and 25 ppm/°C for aluminum
- Operating range and target: −20 to 120 °C, with minimum 0.010 mm gap
Result:
The gap is 0.037988 mm at −20 °C and −0.007470 mm at 120 °C. It reaches the 0.010 mm target at approximately 66.196489 °C. The target is met at colder temperatures in the entered range. The nominal gap reaches zero at approximately 96.994148 °C.
Frequently Asked Questions
Does a hole get bigger when the material expands?
An unconstrained hole in a uniformly warmed material with a positive coefficient gets larger. Use the material's coefficient with the opening's reference dimension.
How do I convert a coefficient written as 12 × 10⁻⁶ per °C?
Enter 12 in the ppm/°C field. The calculator divides ppm by one million in the size formula.
What does a negative signed gap mean?
The insert's modeled free size exceeds the opening. The magnitude measures nominal overlap. It does not estimate the force or deformation of the assembled parts.
Can a warmer assembly have a smaller gap?
Yes. The gap decreases with temperature when the insert's original length times its coefficient exceeds the opening's original length times its coefficient.
Why is a zero-gap temperature sometimes unavailable?
The gap can stay above or below zero throughout the chosen range. With a constant zero gap, equal dimensions persist throughout the range.
Similar Calculators
True Position & Bonus Tolerance Calculator
Calculate true position error from nominal and measured XY centers. Compare circular holes and pins at RFS or MMC, plot the tolerance zone and export CSV.
Unit Converter
Convert between units of length, weight, volume, and area — all in one tool.
Engine Displacement Calculator
Calculate engine size in cc, liters or cubic inches. Compare two bore and stroke combinations and find the dimensions needed for a displacement target.
Slope & Line Equation Calculator
Find slope, intercepts and exact line equations from two points or known coefficients. Graph parallel and perpendicular lines and find the shortest distance from a point.
