Plywood Cut Planner
Turn a rectangular parts list into a sheet-cut plan. Compare eight strategies, inspect cutting geometry and see how kerf and trim affect material use.
Turn your cut list into a plan.
Compare eight rectangular cutting plans. Inspect each piece, cut and remaining rectangle before choosing a layout to review.
Plan found: 1 sheet
Stock and allowances
Unit changes preserve physical dimensions and source text.
Width of material removed, not blade-body thickness.
Total allowance removed from each edge before this plan, including edge-preparation kerf.
One stock size and material/thickness per plan. Width runs along x; length runs along y. Enter finished part dimensions and check your material’s grain or face-pattern direction.
Parts list
1 of 12 part types · up to 100 pieces
Illustrative plans
Best of the 8 plans tried
Plan found: 1 sheet
4 / 4 pieces · 3 production cuts · Area · x-first
Minimum sheet count established by the area bound.
This compares ideal cutting geometry. It does not certify machine operation or optimize every possible layout.
Finished pieces / gross stock
≈97.1899019081 %
Remaining rectangle area
0 m²
Inspect the layout
View from above, with x to the right and y upward. Numbers follow this sheet’s piece selector. The purple outline marks your inspection.
- Width · x from left
- 0 mm to 1220 mm
- Length · y from bottom
- 0 mm to 2440 mm
- Blue numbers: pieces
- Gray hatching: trim
- Amber hatching: kerf
- Green dots: remnants
- Dashed lines: kept edges of cuts
Outlines and cut lines identify geometry; their stroke thickness does not represent material. The drawing preserves physical scale with unused space around the sheet.
Some positive dimensions are smaller than one CSS pixel; inspect the exact coordinate tables.
Lines mark the kept material edge, not blade centerlines. The diagram preserves a single physical scale.
Panel · copy 1
Entered orientation retained.
- x from left
- 10 mm
- y from bottom
- 10 mm
- Width along x
- 598.5 mm
- Length along y
- 1208.5 mm
- Area
- 0.72328725 m²
Where the material goes
- Opened sheets · gross area
- 2.9768 m²
- Area after edge preparation
- 2.904 m²
- Edge-trim removal
- 0.0728 m²
- Finished pieces
- 2.893149 m²
- Production kerf removal
- 0.010851 m²
- Remaining rectangles
- 0 m²
- Pieces / gross area
- ≈97.1899019081 %
- Pieces / usable area
- ≈99.6263429752 %
Gross area equals trim, finished pieces, production kerf and remaining rectangles. Remnants are geometric offcuts; their usefulness depends on your project. Edge-preparation cuts are excluded.
Compare cutting plans
Compare the eight plans tried. Ranking favors more placed pieces, fewer sheets, less production kerf, then fewer cuts. Inspecting a plan keeps your parts list unchanged.
| Rank / strategy | Sheets | Pieces placed | Cuts | Kerf area | Inspect |
|---|---|---|---|---|---|
| 1. Area · x-first | 1 | 4 / 4 | 3 | 0.010851 m² | |
| 2. Area · y-first | 1 | 4 / 4 | 3 | 0.010851 m² | |
| 3. Longest side · x-first | 1 | 4 / 4 | 3 | 0.010851 m² | |
| 4. Longest side · y-first | 1 | 4 / 4 | 3 | 0.010851 m² | |
| 5. Entered width · x-first | 1 | 4 / 4 | 3 | 0.010851 m² | |
| 6. Entered width · y-first | 1 | 4 / 4 | 3 | 0.010851 m² | |
| 7. Entered length · x-first | 1 | 4 / 4 | 3 | 0.010851 m² | |
| 8. Entered length · y-first | 1 | 4 / 4 | 3 | 0.010851 m² |
Complete plan ledgers
Sheets and material accounting (1)
| Sheet | Pieces | Cuts | Gross area | Trim | Finished pieces | Kerf | Remnants |
|---|---|---|---|---|---|---|---|
| 1 | 4 | 3 | 2.9768 m² | 0.0728 m² | 2.893149 m² | 0.010851 m² | 0 m² |
Finished piece coordinates (4)
| Piece / copy | Sheet | x from left | y from bottom | Width x | Length y | Area | Quarter-turn |
|---|---|---|---|---|---|---|---|
| Panel · 1 | sheet-1 | 10 mm | 10 mm | 598.5 mm | 1208.5 mm | 0.72328725 m² | No |
| Panel · 2 | sheet-1 | 10 mm | 1221.5 mm | 598.5 mm | 1208.5 mm | 0.72328725 m² | No |
| Panel · 3 | sheet-1 | 611.5 mm | 10 mm | 598.5 mm | 1208.5 mm | 0.72328725 m² | No |
| Panel · 4 | sheet-1 | 611.5 mm | 1221.5 mm | 598.5 mm | 1208.5 mm | 0.72328725 m² | No |
Production cut sequence (3)
Each cut crosses its already isolated parent rectangle. Parent cuts precede child cuts. Edge preparation is excluded. The geometric sequence is not a machine program or an assessment of safe handling.
| Cut | Sheet / parent | Axis | Kept edge | Span | Nominal kerf | Material kerf | Removed area | Retained / opposite child |
|---|---|---|---|---|---|---|---|---|
| 1 | sheet-1 sheet-1-node-1 | x · vertical | 608.5 mm | 2420 mm | 3 mm | 3 mm | 0.00726 m² | sheet-1-node-2 sheet-1-node-3 |
| 2 | sheet-1 sheet-1-node-2 | y · horizontal | 1218.5 mm | 598.5 mm | 3 mm | 3 mm | 0.0017955 m² | sheet-1-node-4 sheet-1-node-5 |
| 3 | sheet-1 sheet-1-node-3 | y · horizontal | 1218.5 mm | 598.5 mm | 3 mm | 3 mm | 0.0017955 m² | sheet-1-node-6 sheet-1-node-7 |
Remaining rectangles (0)
No positive-area remaining rectangles.
Save or reuse this cut list
Saved input includes unfinished drafts. A report includes all eight comparisons and the selected plan’s complete sheets, pieces, cuts, remnants and unplaced demand.
Saved input · selectable fallback
Complete report · selectable fallback
Preview and apply an input file
Use an exported input file, not a result report. Preview checks the whole file before you replace the current cut list.
Method and limits
Eight deterministic strategies combine four part orderings with width-first or length-first cuts. Each placement uses an already separated rectangular piece of stock. Free rectangles are never merged. The best tried plan is ranked by placed pieces, sheets, production kerf and cut count.
An exact whole-edge fit needs no extra cut or phantom kerf. A final sliver narrower than the blade’s nominal kerf is wholly removed from its isolated rectangle. The report distinguishes nominal kerf from material actually removed.
Locked parts keep entered width along x and length along y. A permitted quarter-turn exchanges those dimensions. Grain, face patterns, material strength, stock defects and machine handling are not inferred.
The area bound alone does not construct a layout. Equality with a complete feasible plan establishes minimum sheet count under this geometry; other results do not prove a globally optimal layout. All examples are editable illustrations.
How to use this calculator
- Enter Stock width and Stock length, then choose Length unit. Use one stock size and material/thickness basis for the plan. Width is the x-axis and length is the y-axis; the drawing starts at the lower-left corner. Dimensions are finished geometric sizes, not product recommendations.
- Enter Saw kerf and Edge trim. Kerf is the width of material removed by a production cut, which can differ from the blade body's thickness. Trim is the total allowance already removed from each stock edge, including edge-preparation kerf; these preparation cuts are excluded from the production cut count.
- Add each part's name, width, length and Quantity. Choose whether Rotation is locked or a quarter-turn is allowed. Locked pieces keep the entered width and length axes. Decide permission from the actual face grain, pattern and project requirements; the planner does not infer grain or structural suitability.
- Compare all eight tried strategies and inspect their sheet counts, production cuts and material totals. The best-ranked plan uses the declared criteria, not an unrestricted optimization search. An incomplete result identifies pieces that cannot fit a fresh usable sheet under their rotation rules; its sheet count serves only the placeable subset.
- Choose a candidate and sheet, then inspect parts, cuts and remaining rectangles through the native controls and ledgers. Cut order follows isolated parent rectangles. Small bands may be hard to distinguish at the drawing scale, so use exact dimensions and identities rather than estimating from pixels. The diagram is not a machine-control program.
- Use Input file format and Input text to preview to stage a complete CSV or TSV input before applying it. Reusable input preserves unfinished drafts. A complete report requires valid inputs, includes all eight summaries and the selected plan's complete ledgers, and can honestly report an incomplete geometric order.
The Formula
The mathematical logic powering this calculation is:
Usable width = stock width − 2 × edge trim; usable length = stock length − 2 × edge trim. Trim is total material already removed during edge preparation, including its kerf. The production cut tree starts with this usable rectangle.
For a cut retaining extent a in an isolated parent extent D, delta = D − a. When delta = 0 there is no cut. Otherwise the in-material kerf is min(entered kerf, delta), and any positive opposite remainder is retained. The second cut spans only the first retained strip, so its kerf does not count the corner twice. Zero-kerf separation still counts as a cut.
Compare decreasing area, longest side, entered width and entered length, each with x-first and y-first subdivision. Test all existing free rectangles and allowed orientations using exact leftover-area and residual-dimension scores before opening a fresh sheet. Never merge separated remnants. Rank by placed count, sheet count, production kerf area, cut count and declared strategy order.
Gross stock area = trim removal + finished-part area + production kerf removal + terminal remnant area. Gross utilization = finished-part area / opened gross stock area; usable utilization uses opened usable area instead. The area-only sheet bound is ceil(placed-part area / one usable sheet area). Only a complete plan reaching its whole-order bound establishes minimum sheet count; it does not establish minimum cuts or kerf.
Geometry, fit decisions and area accounting use exact rational values. One inch is exactly 0.0254 m, and one international square foot is exactly 0.09290304 m². Display rounding does not alter a placement.Worked Example
If you input:
- Length unit: mm
- Stock width: 1220 mm
- Stock length: 2440 mm
- Saw kerf: 3 mm
- Edge trim: 10 mm on each edge
- Part name: Panel
- Part width: 598.5 mm
- Part length: 1208.5 mm
- Quantity: 4
- Rotation: Locked
Result:
One sheet supplies all four panels with three production cuts and no terminal remnants. Its usable rectangle is 1200 × 2420 mm. Gross area 2.9768 m² equals trim 0.0728 m² + panels 2.893149 m² + production kerf 0.010851 m² + remnants 0 m². The complete plan meets the one-sheet area lower bound, establishing minimum sheet count under this geometric model, without a claim of minimum cuts or machine suitability.
Frequently Asked Questions
Why is dividing total part area by sheet area not enough?
Area ignores dimensions, orientation and material removed by cuts. Two 6 × 6 pieces have total area 72 and therefore an area-only bound of one 10 × 10 sheet, yet they cannot both fit that sheet without overlap. This planner constructs a feasible guillotine partition and reports the bound separately. Equality between a complete feasible sheet count and its bound proves minimum sheet count for that input, but a larger count is not a known optimality gap.
Does the best tried plan guarantee an optimal cut list?
The comparison tries eight fixed combinations of part ordering and subdivision direction. Existing free rectangles are evaluated before opening new stock, and separated leaves are not merged. Best means first in the declared ranking: placed pieces, sheets, kerf area, cuts and strategy order. It is not a search over every possible nesting arrangement. A minimum-sheet certificate is shown only when a complete feasible plan reaches its independent area bound.
What should I enter for kerf and edge trim?
Use the cutting width appropriate to your actual blade and process; the blade body's thickness can differ from the removed width. The example's 3 mm is illustrative. Edge trim includes all material already removed to obtain the usable rectangle, including preparation kerf, so it is not charged again. If a final isolated sliver is narrower than nominal kerf, only the intersected material is counted as removed. This geometry does not specify a safe saw setup.
How does grain direction affect rotation?
A locked part retains its entered width along x and length along y. Allowing rotation also permits a 90-degree orientation, except that a square has no distinct second orientation. Choose the permission for the actual sheet face grain, pattern and project requirements. A supplier may describe grain running along its sheet's long dimension, but this is not a universal inference from a plywood label or a structural design check.
What does an incomplete or empty plan mean?
A valid oversized piece is listed as unplaceable when neither permitted orientation fits a fresh usable sheet. Other individually fitting pieces are placed because the model can open fresh sheets up to its bounded request. An incomplete plan's sheet count and area bound apply to that placeable subset. If no pieces fit, there are no opened sheets and utilization is unavailable rather than zero percent. Invalid input is a separate state and blocks the result report.
Are the cuts executable instructions and the remnants reusable stock?
Each cut traverses an isolated parent rectangle, and the ledger records its kept edge, actual material band and child identities. This establishes a geometric guillotine sequence, not blade-center coordinates, machine instructions or a safe handling plan. A remnant is a positive terminal rectangle. The calculator does not decide whether it is safe, useful or valuable, and it does not reuse an external offcut inventory or mix stock thicknesses.
What is preserved when I change units or save an unfinished plan?
Validated exact anchors preserve physical dimensions and restore original source text when returning to its unit. A malformed dimensional atom refuses conversion without erasing it; unrelated invalid quantities, labels or rotation drafts remain editable. Unknown imported units require explicit declaration, not a guessed conversion. Reusable CSV or TSV preserves ordered parts and unfinished fields. The report is a separate geometry document and requires valid inputs, while still allowing an explicitly incomplete order.
Similar Calculators
Siding Calculator
Estimate siding for walls and gables with validated door and window openings, exposed pack coverage, waste, whole-pack quantities and material costs.
Wallpaper Calculator
Estimate wallpaper rolls with pattern repeat, half-drop matching, trim and spare rolls. See a wall-by-wall strip layout, cutting schedule and cost.
Unit Converter
Convert between units of length, weight, volume, and area — all in one tool.
Plank Flooring Layout & Cost Calculator
Compare plank flooring layouts, staggered rows and compatible offcut reuse. Visualize cuts, check entered installation limits, estimate whole packs and project costs.
Lumber Cut List & Purchase Planner
Optimize a lumber cut list across existing boards and supplier stock lengths. Compare purchase costs, saw kerf, offcuts and board-foot pricing with visual cutting layouts.
