Siding Calculator
Plan siding for rectangular walls and centered gables, with doors and windows positioned on a scaled elevation. Compare opening deductions, waste and whole-pack quantities using the product’s exposed coverage; export the wall measurements and material estimate.
Plan siding by wall and opening
Map rectangles and gables, check opening positions, and compare whole-pack quantities using the product’s exposed coverage. An area estimate, not a cutting layout.
Try a project
Switching units converts measurements and coverage. It keeps the same physical project and USD pack price.
Wall 1
Total peak height is eave height plus gable rise. All dimensions are physical measurements; no hidden waste is added.
Doors and windows (1)
Enter rectangular openings from the lower-left corner of this wall. Left and bottom offsets locate the opening’s lower-left corner. Openings must fit inside the face, including sloping edges, and cannot overlap. Shared edges are allowed.
Purchase assumptions
Full deduction uses actual net area. Keeping half or all of the opening area adds a planning allowance before waste. Small openings may save little material after cuts; choose an approach appropriate to the product. These options do not prove offcuts are reusable.
Applied after the opening deduction. The default 10% is an editable example, not a product-specific requirement.
Use the manufacturer’s installed exposed coverage for the exact pack sold. Nominal board width can include covered laps. One pack may mean one board if its exposed coverage and price are entered consistently.
Illustrative editable price. Material only; excludes trims, starter strips, fasteners, labor, delivery and tax.
How to use this calculator
- Choose Measurement units, then select each Wall shape. Enter Width and Height, or Eave height plus Gable rise above eaves for a rectangle with a gable. Triangle-only walls use Peak height.
- Add each rectangular door or window with its Left offset, Bottom offset, Opening width and Opening height. Offsets start at the wall’s lower-left corner. Correct openings that overlap or extend past the face or sloping roofline.
- Choose Opening deduction for purchasing: keep all opening area, deduct half, or deduct all. Enter Additional waste allowance separately. The Actual net wall result always subtracts all valid openings regardless of the purchasing choice.
- Enter the manufacturer’s installed Exposed coverage per pack and Price per pack in USD. Use the exact package sold and its effective coverage after overlap, rather than nominal board dimensions.
- Review Whole packs to plan for, Coverage breakdown, Scaled wall elevation and Wall quantities. Expand Opening positions and deduction comparison to inspect coordinates and the effect of alternative allowances.
- Export the estimate CSV and check the actual product lengths, cutting requirements, accessories and final order with the supplier or installer. The estimate excludes installation, structural design, trims, delivery and tax.
The Formula
The mathematical logic powering this calculation is:
Rectangle area = width × height. Triangle area = width × peak height ÷ 2. Rectangle + gable area = width × eave height + width × gable rise ÷ 2.
Actual net area = gross wall area − all validated opening areas.
Purchasing base = gross wall area − opening deduction fraction × opening area, where the fraction is 0, 0.5 or 1.
Required exposed coverage = purchasing base × (1 + waste percentage ÷ 100). Whole packs = ceiling(total required coverage ÷ exposed coverage per pack).
Material cost = whole packs × entered pack price. Round packs once after combining all walls; this is an area estimate, not a cut layout.Worked Example
If you input:
- Measurement units: Metric — metres and m²
- Wall shape: Rectangle + centered gable
- Width: 6 m
- Eave height: 3 m
- Gable rise above eaves: 2 m
- Left offset: 2 m
- Bottom offset: 1 m
- Opening width: 2 m
- Opening height: 1 m
- Opening deduction for purchasing: Deduct all opening area
- Additional waste allowance: 10%
- Exposed coverage per pack: 5 m²
- Price per pack: $60 USD
Result:
The wall has 6 × 3 + 6 × 2 ÷ 2 = 24 m² of gross area. Its 2 × 1 m window fits inside the rectangle and removes 2 m², leaving 22 m² of actual net area. Full opening deduction and 10% additional waste require 22 × 1.10 = 24.2 m² of exposed coverage. Ceiling(24.2 ÷ 5) = 5 whole packs supply 25 m², leaving 0.8 m² above the required coverage. The material estimate is 5 × $60 = $300, excluding accessories, labor, delivery and tax.
Frequently Asked Questions
Should doors and windows be subtracted from siding area?
The actual net wall area subtracts every validated opening. Purchasing is a separate decision: you can deduct all, half or none of that opening area before applying waste. A small opening may save little material if full pieces still need to be cut around it. These choices are transparent planning allowances, not a universal manufacturer rule or proof that offcuts are reusable. CertainTeed’s basic rectangle estimating guidance keeps doors and windows included; consult the instructions for your chosen product.
How are gables and sloping edges measured?
A triangle-only face uses width × peak height ÷ 2. A rectangle with a centered gable adds that triangular area to width × eave height, using the separate gable rise above the eaves. The model uses true geometric area with no hidden extra height or waste. Openings must fit inside the resulting polygon, including both top corners beneath any slope. Off-center peaks, trapezoids, dormers and curved faces are not supported.
What is exposed coverage, and why not use nominal board width?
Exposure is the visible installed face after the required overlap. Multiplying nominal board dimensions can overstate the area that remains exposed. Enter the exact manufacturer-stated installed coverage for the pack being purchased, or its properly calculated exposed coverage. If material is sold by individual boards, treat one board as a pack and enter that board’s exposed coverage and price together. The tool does not infer lap, reveal, board length or installation orientation.
Why do I need positions for each opening?
A left and bottom offset locate each opening’s lower-left corner within its own wall. Positions allow the tool to reject openings that extend beyond the face or overlap, which would otherwise subtract nonexistent or duplicate area. Rectangular openings may share an edge. The wall elevation shows their actual placement and the CSV records every position. The geometry check does not design lintels, framing, flashing or weatherproofing.
Does 10% waste guarantee enough siding?
No. The default is an editable illustration. Product lengths, gables, installation direction, joints, cuts, breakage and usable offcuts can change the required allowance. Waste is applied to the purchasing base after the chosen opening deduction, then total required coverage is rounded up to whole packs once for the project. Material reserved by the opening policy and excess caused by pack rounding are shown separately. A detailed installation takeoff may require more material.
What is included in the cost estimate?
Only whole siding packs multiplied by the entered USD price per pack. The price is an editable assumption rather than a current supplier quote. Trims, starter strips, flashings, fasteners, labor, tax and delivery are excluded. The wall diagram is a scaled elevation, not a board placement or cutting plan, and the quantities do not verify product suitability, local installation rules or structural performance.
What happens when I switch units or export the estimate?
Metric uses metres and square metres; imperial uses feet and square feet. Unit switching converts wall and opening measurements plus exposed pack coverage, preserving the physical project and the pack price. Blank or non-finite measurements must be completed first. The CSV includes the selected assumptions, canonical metre measurements, per-wall and opening areas, retained opening allowance, waste, whole-pack rounding and material cost. Up to 20 walls and 20 openings per wall are supported.
Similar Calculators
Roof Area Calculator
Plan shed, gable and hip roof area, faces and edges. Compare roofing, underlayment, starter and cap quantities with exact whole-pack purchasing, diagrams and CSV.
Paint Coverage Calculator
Estimate paintable wall area, paint needed, gallons to buy, and project cost with room-by-room deductions.
Wallpaper Calculator
Estimate wallpaper rolls with pattern repeat, half-drop matching, trim and spare rolls. See a wall-by-wall strip layout, cutting schedule and cost.
Brick Masonry Calculator
Estimate brick count, mortar volume, wall area, waste allowance, and masonry material cost.
