Hardwood Floor Refinishing Cost Calculator

Compare one or two hardwood floor refinishing quotes using your measured areas and the treatments each contractor proposes. Enter full sand and refinish rates, recoat rates, repair allowances and fixed charges. See where the recorded work differs, how the minimum charge affects each price endpoint and how the quoted restriction on floor access compares.

Wood floor quotes

Hardwood floor refinishing planner

Compare treatments, itemized prices and quoted access downtime by area.

Measured areas and treatments

Area 1
Area 2
Area 3

Contractor prices and downtime

For a fixed price, leave High blank. Enter 0 if the quote states no mobilization charge or area-work minimum.

Full sand and refinish rates

Labor (USD/sq ft)
Finish (USD/sq ft)

Recoat rates

Labor (USD/sq ft)
Finish (USD/sq ft)
Board repairs (quote total)
Preparation and protection (quote total)
Mobilization (quote total)
Quoted days without floor access

Compare quote scope and cost

Recorded area treatments match. The cost ranges overlap or touch.

AreaMeasuredQuote AQuote B
Living room360 sq ftFull sand and refinishFull sand and refinish
Hallway90 sq ftRecoatRecoat
Entry repair area30 sq ftRepair onlyRepair only

Entered quote ranges

  • Quote A$1,825.00–$2,128.00

  • Quote B$1,826.00–$2,090.50

Quote B minus Quote A can range from −$302.00 to $265.50 across the entered endpoints.

Quoted access downtime

  • Quote A3–5 days

  • Quote B2–4 days

Use the contractor’s quoted access restriction and the finish manufacturer’s instructions.

Confirm the proposed treatment for the existing floor with the contractor. Wear layer, remaining material and finish compatibility affect the work.

Refinishing quote ledger

The area-work minimum can add more to the low-cost case. Each column uses its own work subtotal.

Quote A

ChargeArea and rateLow-cost caseHigh-cost casePrice status
Full sand and refinish · labor360 sq ft × $2.60–$3.10/sq ft$936.00$1,116.00Entered
Full sand and refinish · finish360 sq ft × $0.90–$1.10/sq ft$324.00$396.00Entered
Recoat · labor90 sq ft × $1.20–$1.40/sq ft$108.00$126.00Entered
Recoat · finish90 sq ft × $0.40–$0.50/sq ft$36.00$45.00Entered
Minimum area-work top-up—$96.00$0.00Entered
Board repairs—$180.00$260.00Entered
Preparation and protection—$50.00$90.00Entered
Mobilization—$95.00$95.00Entered
Entered quote total$1,825.00$2,128.00Priced

Quote B

ChargeArea and rateLow-cost caseHigh-cost casePrice status
Full sand and refinish · bundled rate360 sq ft × $3.45–$3.90/sq ft$1,242.00$1,404.00Entered
Recoat · bundled rate90 sq ft × $1.60–$1.85/sq ft$144.00$166.50Entered
Minimum area-work top-up—$0.00$0.00Entered
Board repairs—$220.00$300.00Entered
Preparation and protection—$70.00$70.00Entered
Mobilization—$150.00$150.00Entered
Entered quote total$1,826.00$2,090.50Priced

How to use this calculator

  1. Enter the non-overlapping measured areas and each quote’s proposed treatment. Mark omitted work Excluded and record repair-only areas separately.
  2. Choose Edit Quote A or Edit Quote B, then enter either split labor and finish rates or one bundled rate for each active area treatment.
  3. Enter any applicable total board-repair and preparation charges, mobilization and the quote’s area-work minimum. Leave High blank for a single amount.
  4. Enter the contractor’s quoted days without floor access when supplied. Review Compare quote scope and cost before interpreting the range comparison.
  5. Open the Refinishing quote ledger and download the CSV to keep exact charges, missing prices, scope and downtime.

The Formula

The mathematical logic powering this calculation is:

For each quote, total the measured areas that use full sanding or recoating separately. Area-work price for each treatment equals that area multiplied by the bundled rate or by the entered labor rate plus the finish rate. Finish refers to the finish or material charge stated in the quote. Repair-only areas record scope and use the entered board-repair allowance as a total charge.

For each endpoint, calculate area work first. If the area-work subtotal is below the entered minimum, the top-up is the minimum less that subtotal. Apply the minimum only where the quote includes full sanding or recoating. Add the board-repair allowance, preparation and protection charge, and mobilization after that step. The minimum top-up can be larger in the low-cost case. Enter amounts in the matching field to avoid counting a bundled charge twice.

A blank high uses the entered low as a fixed amount. Required blanks keep the total unavailable while the known charges remain visible. Applicable area rates, area-work minimum, mobilization, and a repair allowance for any repair-only area are required for a complete entered total. Enter zero for a required charge explicitly included or waived in the quote. An omitted optional charge contributes nothing to the entered amount and stays labeled in the ledger. Quoted access downtime remains an independent input.

Compare prices directly when the same treatment is recorded for each measured area. The difference interval is B low − A high to B high − A low. Overlapping or touching ranges leave multiple price orderings possible. The endpoints pair the entered low values with each other and the high values with each other. They describe input scenarios. All costs use exact arithmetic and round only for currency display.

Use 1 to 6 non-overlapping measured areas. Area accepts above 0 through 1,000,000 sq ft, with up to three decimal places. Rates accept nonnegative values through 1,000,000 per sq ft. Fixed amounts and minimums accept nonnegative values through 1 billion. Money allows two decimal places. Quoted downtime accepts 0 to 1,000 days and up to three decimal places. The currency selector labels the entered values. Confirm treatment and floor access with the contractor and applicable manufacturer guidance.

Worked Example

If you input:

  • Hypothetical scope: Sand 360 sq ft, recoat 90 sq ft, repair-only area 30 sq ft
  • Quote A minimum for area work: $1,500
  • Quoted days without floor access: A 3–5 days, B 2–4 days

Result:

In these sample quotes, A has an area-work subtotal of $1,404–$1,683 before its minimum. The minimum adds $96 in the low-cost case and $0 in the high-cost case. Quote A totals $1,825–$2,128 and Quote B totals $1,826–$2,090.50. The recorded area treatments match and the cost ranges overlap.

Frequently Asked Questions

How is a recoat different from a full sand and refinish?

A maintenance recoat adds fresh finish after suitable preparation of the existing finish. Full sanding and refinishing removes more of the old surface before the new finish. A qualified flooring professional can determine which treatment the floor and finish can support.

What if one contractor excludes a room or uses a different treatment?

Record each quote’s treatment for that measured area. The scope table highlights the difference. Individual entered costs remain available, and the direct price difference is unavailable until each area has matching recorded treatment.

Does the area-work minimum apply to repairs and mobilization?

This worksheet applies the entered minimum to the sanding and recoating subtotal. It then adds the separately entered repairs, preparation and mobilization. Use this minimum field when your quote defines the minimum on that basis.

When should I enter zero?

Enter zero when a quote explicitly includes or waives an applicable separate charge. Leave an unknown amount blank so the ledger can show it as unpriced or omitted. A blank High paired with a valid Low means one fixed price.

Does the calculator estimate cure time or confirm that a floor can be sanded?

The downtime field records the contractor's quoted restriction on access. Finish instructions and site conditions govern access and cure. Floor construction, remaining wear layer and finish compatibility inform whether sanding or recoating is appropriate.

How are local pricing and taxes handled?

Use amounts from the quotes you want to compare. The worksheet adds the specified cost components and applies the stated minimum. Include any applicable tax in comparable entered prices if you want it reflected in the total.

How do I include isolated board repairs?

Mark a measured area Repair only when that is the quoted treatment. Enter the total board-repair allowance. For repairs alongside sanding or recoating, use the same separate allowance and keep area treatment as stated in the quote.

Similar Calculators