Window Film Light Transmission & Quote Planner
Measure the exposed rectangular glass and record before-and-after visible light transmittance for the same glazing. Compare two film proposals while finding how trimmed pane cuts fit into finite supplier rolls. Review before-and-after VLT, whole-roll material, trim and entered installation costs in one worksheet.
Compare window film, light and roll fit
Use matching glazing readings, then compare finite roll layouts and entered installation quotes.
Example VLT comes from published glass references. Roll dimensions and prices are illustrative.
Proposal A
$257.00
- Reference VLT
- 64.3333%
- Whole rolls
- 2
- Treated area
- 36 ft²
- VLT change
- -17.6667 pp
Proposal B
$229.00
- Reference VLT
- 31%
- Whole rolls
- 1
- Treated area
- 36 ft²
- VLT change
- -51 pp
Proposal B is $28.00 lower for the entered work.
Complete quote for Proposal A. Complete quote for Proposal B. 64.3333% VLT for Proposal A. 31% VLT for Proposal B. Proposal B is $28.00 lower for the entered work.
Visible light transmission
Visible light transmittance (VLT) uses your glass measurements or published references. The weighted comparison assumes equal incident light per unit of exposed glass.
Before film82%
Proposal A64.3333%
Proposal B31%
Proposal A change from before
- Percentage points
- -17.6667 pp
- Relative change
- -21.5447%
Proposal B change from before
- Percentage points
- -51 pp
- Relative change
- -62.1951%
Measured panes and trimmed cuts
Side panes · 2 panes · 24 ft² · 3M sample · dual ¼ in clear glass
- Exposed glass
- 24 × 72 in
- Raw cut
- 25 × 73 in
- Before VLT
- 79%
- After VLT
- 62%
- Exposed glass
- 24 × 72 in
- Raw cut
- 25 × 73 in
- Before VLT
- 79%
- After VLT
- 30%
Finite roll cut plans
Each cut stays in one piece. The model finds the fewest rolls under the horizontal shelf policy and the approved orientations.
Proposal A roll layout
- Usable width × length
- 48 × 150 in
- Shelf bands
- 2
- Length occupied
- 122.25 in
- Trailing length
- 27.75 in
- Front pane 1 · 37 × 49 in raw · 0 in from width edge, 0 in from start
- Side panes 2 · 25 × 73 in raw · 0 in from width edge, 49.25 in from start
Proposal B roll layout
- Usable width × length
- 55 × 126 in
- Shelf bands
- 2
- Length occupied
- 122.25 in
- Trailing length
- 3.75 in
- Front pane 1 · 37 × 49 in raw · 0 in from width edge, 0 in from start
- Side panes 1 · 25 × 73 in raw · 0 in from width edge, 49.25 in from start
- Side panes 2 · 25 × 73 in raw · 25.25 in from width edge, 49.25 in from start
Edit pane measurements and VLT
Use one glass-plane reference for before and after on each row. Describe the actual measured or published assembly.
3 measured panes · 36 ft² of exposed glass
The exact cut plan supports up to twelve panes across eight groups.
Edit Proposal A stock and prices
Edit Proposal B stock and prices
Show material and quote ledger
| Quantity or quote | Proposal A | Proposal B |
|---|---|---|
| Treated exposed area | 36 ft² | 36 ft² |
| Raw cut area | 37.9375 ft² | 37.9375 ft² |
| Trim included in cuts | 1.9375 ft² | 1.9375 ft² |
| Purchased stock area | 100 ft² | 48.125 ft² |
| Remaining outside cuts | 62.0625 ft² | 10.1875 ft² |
| Material | $116.00 | $97.00 |
| Installation | $117.00 | $108.00 |
| Other quoted costs | $24.00 | $24.00 |
| Complete quote | $257.00 | $229.00 |
Export results
Download window film comparison CSVShow selectable CSV text
How to use this calculator
- Enter the exposed glass width, height and count for each architectural pane group. Record the matching glass assembly or sample reference.
- Enter before VLT and with-film VLT as percentages for each treated proposal. Use the glass-plane basis for both readings, and leave a pane untreated in an offer as needed.
- Enter usable roll width and length, raw trim allowance, and gap. Turn on a quarter-turn only for an approved orientation.
- Compare VLT changes and physical quotes. Inspect each roll and its exact pane cut positions.
- Open the quote and materials ledger or download the complete comparison CSV.
The Formula
The mathematical logic powering this calculation is:
Each group uses rectangular exposed glass. Multiply pane width by height and count for group area. Divide square inches by 144 for square feet. Enter glass-plane visible light transmittance before and with each candidate film, using the same glazing and a matching reference measurement basis. An untreated pane retains its before value. The worksheet uses the entered combined glass-and-film values directly.
Change in percentage points equals after minus before. Relative change equals 100 × (after − before) ÷ before, when before is positive. A zero before value keeps percentage-point change and makes relative change unavailable. Multiply each value by its group’s exposed area and divide their sum by total exposed area for the equal-incident reference. This reference assumes equal incident visible light per unit glass area, with no statement about actual room illuminance, privacy, heat or energy savings.
Each filmed pane gets one raw rectangle. Raw width and height add twice the per-edge trim to exposed width and height. A quarter-turn interchanges those dimensions when permitted by your selected offer. Each roll is divided along its length into shelves. A shelf contains one or more cuts across the usable width with the entered gap between them. Shelf height equals its longest cut. The same gap separates successive shelves. For each pane subset, the smallest feasible shelf height is found by trying each allowed height and choosing the narrowest matching cut orientation per piece. Exact subset partitioning then minimizes rolls across all feasible shelves under this policy. Each cut stays within one physical roll. General nesting outside horizontal shelves is a separate decision.
Whole rolls × quoted price plus treated square feet × installation rate plus the entered fixed amount gives total cost. Material and labor are zero for untreated scope. The installation line rounds to cents with ties upward. Total bought area equals exposed film area, raw trim, and remaining stock outside raw cuts. Remaining stock contains both possible remnants and gaps. A valid optical estimate remains visible when the stock cannot fit; an available stock quote remains visible when optical inputs are incomplete.
Use one to eight pane groups and up to twelve panes total. Pane dimensions are 0.001–500 in, usable roll width 0.001–1,000 in and roll length 0.001–4,000 in. Trim and gaps are 0–12 in, VLT 0–100%, and measurements and VLT accept up to three decimals. Prices accept cents. Stock examples and prices are illustrative. Source measurements apply to their named reference glazing. Glass type, film compatibility and installation instructions should come from the project’s actual products.Worked Example
If you input:
- Exposed panes: One 36 × 48 in single clear and two 24 × 72 in dual clear panes
- Reference transmission: Single clear 88% before, 69% with PR70, 33% with NV35. Dual clear 79% before, 62% with PR70, 30% with NV35.
- Illustrative stock: A uses 48 × 150 in rolls. B uses 55 × 126 in. Each has 0.5 in trim per edge, 0.25 in cut gaps, and fixed orientation.
- Entered pricing: A $58 per roll, $3.25 per installed ft² and $24 fixed. B $97 per roll, $3 per installed ft² and $24 fixed.
Result:
Across 36 ft², the equal-incident VLT reference is 82% before, 64.3333% with A and 31% with B. Both plans need the same three raw pieces. The two narrower rolls cost $257.00 installed in A. Both tall cuts fit side by side in B's one roll, for $229.00 installed.
Frequently Asked Questions
Can I multiply the film percentage by the existing glass percentage?
Enter the visible transmittance for that glazing with the film already included. Film names and film-only transmission percentages do not describe the same assembly. Published glass tables vary by the original substrate.
Where can I find the before and after percentages?
Use consistent measurements on the same glazing or a technical data table with matching clear, tinted, single or dual reference glass. Keep whole-window ratings with their frame basis separate from exposed glass data.
Does the average predict a room’s brightness?
The average weights by measured exposed area under the same incident light per unit area. Actual light varies with direction, surrounding obstructions and the room.
Why can a roll with enough area still fail?
Each raw pane cut has to fit as one rectangle in an allowed orientation. Total area cannot compensate if either cut dimension fails.
What is a shelf in the cut plan?
It is a band across the roll holding one or more side-by-side pieces. Its height is the longest cut along the roll. The model minimizes roll count over those shelf layouts.
Does the trim affect my visible light average?
Trim increases raw cut dimensions only. Visible transmission is weighted by measured exposed glass.
Similar Calculators
Window Replacement Cost & Quote Calculator
Compare window replacement quotes by opening, installation, allowances and rebates. Explore optional heating savings, payback and net present value with charts and CSV.
Carpet Calculator: Roll Layout, Seams & Cost
Compare carpet roll offers, room seams and entered material prices. Inspect linked cutting plans, trim allowances and purchasing length.
Gift Wrap Roll & Box Cut Planner
Calculate how much wrapping paper fits your boxes. Compare two rolls, set fold overlaps and see a scaled cut plan with leftover paper.
Plywood Cut Planner
Plan rectangular plywood cuts with kerf and rotation constraints. Compare eight sheet layouts and inspect parts, cuts and remnants.
