Wheelchair Ramp Length & Slope Calculator

Find the horizontal space needed for a straight wheelchair ramp, including the level areas at both ends and between runs. Enter the total rise and clear site dimensions, compare several slopes, and see how the space changes when you add a landing. Use the side profile, table and CSV to review each ramp segment and its finish elevation.

Rise, slope and landings

Plan a straight wheelchair ramp

Compare running slopes, see the space taken by runs and landings, and check four general U.S. ramp dimensions.

Layout measurements

Measure between finished surfaces. Include space for bottom, intermediate and top landings.

Unobstructed width, between handrails where present.

Same clear length for each level landing.

Enter 14 for 1:14, or 14 horizontal units per unit of rise.

Clear space required

64 ft

768 in long × 42 in wide

Needs more clear space

Length
8 in short
Width
6 in left
Runs and landings
2 runs · 3 landings
Rise per run
21 in
Running grade
7.1428571% · 4.0856168°
Along the surface
769.49809 in

ADA dimensional benchmarks

Meets all four modeled dimensions.

  • Running slope1:12 or gentlerMeets
  • Rise per run30 in maximumMeets
  • Clear width36 in minimumMeets
  • Landing length60 in minimumMeets

Each run rises over 6 in, the §405.8 threshold for handrails under the general rule.

Checks use the inch-based limits in 2010 ADA §405. Site review also includes cross slopes, handrail geometry, edges, surface, door approaches and applicable local rules.

Straight ramp profile

2 equal-rise runs with a landing at each end and between runs. Elevation is exaggerated for readability.

Start · 0 inEnd · 768 in
  • Runs
  • Landings
  • Available length

Length by running slope

The run count and landings stay fixed. The vertical marker shows 760 in available.

  • 684 in

    76 in left

  • 768 in

    8 in short

  • 852 in

    92 in short

  • 936 in

    176 in short

Bars show the horizontal runs followed by the combined landing length.

Show ramp segment table
Straight ramp profile measurements
SegmentStart positionEnd positionStart elevationEnd elevationHorizontal lengthSurface length
Landing 10 in60 in0 in0 in60 in60 in
Run 160 in354 in0 in21 in294 in294.74905 in
Landing 2354 in414 in21 in21 in60 in60 in
Run 2414 in708 in21 in42 in294 in294.74905 in
Landing 3708 in768 in42 in42 in60 in60 in

Export the layout

Save the measurements, grade comparison, numeric checks and profile stations in millimeters.

Download ramp CSV
Show selectable CSV

How to use this calculator

  1. Start with Two-run space comparison or One-run entry example. Choose Dimension units and enter Total vertical rise measured between finished surfaces.
  2. Enter Available straight length and Available clear width for the whole uninterrupted layout. Enter Run and landing clear width and Each landing length. Include both end landings in your space measurements.
  3. Enter Running slope denominator, such as 14 for 1:14. Choose Minimum by 30 in rise limit or Set run count to compare a specific number of equal-rise runs.
  4. Read Clear space required for the overall footprint and signed space margins. Use ADA dimensional benchmarks to check the selected slope, rise per run, clear width and landing length values separately.
  5. Select an alternate ratio in Length by running slope to update the Straight ramp profile. Open Show ramp segment table or Download ramp CSV to inspect run and landing positions.

The Formula

The mathematical logic powering this calculation is:

For total vertical rise H and slope 1:R, the horizontal runs together need H × R. Grade is 100/R percent and the angle in degrees is arctan(1/R) × 180/π. With N equal-rise runs, each gains H/N and needs horizontal distance H × R/N. Count N + 1 level landings because each intermediate landing serves both adjacent runs. With common landing length L, the total straight footprint is H × R + (N + 1)L. The distance along the finished surfaces is √[H² + (H × R)²] + (N + 1)L. Clear landing width equals clear run width in this layout.
Available length minus footprint gives the length margin. Available clear width minus planned clear width gives the width margin. Nonnegative values in both axes indicate a geometric fit in the entered clear envelope. The comparison varies the slope denominator while holding count, rise and landings fixed. With the minimum run-count option, the tool rounds H ÷ 30 in upward to a whole number using the inch-based rise benchmark.
For slopes steeper than 1:20, the limited 2010 ADA §405 dimensional comparison uses the published inch-based general limits: 1:12 or gentler running slope (§405.2), no more than 30 in rise per run (§405.6), at least 36 in clear width (§405.5) and at least 60 in clear landing length (§405.7.3). Each landing is drawn level and as wide as the adjoining runs. The handrail flag uses the greater-than-6-in rise threshold in §405.8. At 1:20 or gentler the workspace identifies the walking-surface grade described in §403 and shows geometry for the landings entered. Inch-based benchmark results stay the same when measurements display in mm.
The inputs support a total rise from 0.1 to 9,144 mm equivalent, other dimensions from 0.1 to 300,000 mm equivalent, slope denominators from 4 to 30, and 1 to 24 straight runs. Enter plain decimals with up to six fractional digits. Exact 25.4 mm-per-inch conversion and integer arithmetic control the site fit and benchmark boundaries. A rounded converted input retains its exact original dimension until edited. The profile uses separate horizontal and vertical scales and the CSV gives distances in millimeters.
This worksheet covers a straight layout with uniform slope, rise and width, using the same length for each landing. Site design also accounts for surface conditions, tolerances, cross slopes, rail and edge construction, doors, local requirements and the applicable accessibility standard. Turns, curb ramps and alteration exceptions require their own layout and checks.

Worked Example

If you input:

  • Total vertical rise: 42 in
  • Available straight length: 760 in
  • Available clear width: 48 in
  • Run and landing clear width: 42 in
  • Each landing length: 60 in
  • Running slope denominator: 14
  • Run count method: Minimum by 30 in rise limit

Result:

With two equal 21 in rises, the horizontal runs add up to 588 in. Three landings add 180 in, making 768 in (64 ft) overall. The layout needs 8 in more length and leaves 6 in of clear width. At 1:12, the same two-run layout needs 684 in (57 ft), leaving 76 in of length.

Frequently Asked Questions

How long is a 1:12 ramp for a 30-inch rise?

The sloped run needs 360 horizontal inches, or 30 feet. A single straight run with 60-inch landings at each end needs 40 feet of clear horizontal length in this model.

What is the difference between horizontal length and surface distance?

Horizontal length is the straight plan distance used to check the site envelope. Surface distance follows the slope of each run and the level landings. The profile and segment table give both measurements.

Why does the ramp get longer when I add runs at the same slope?

At a fixed overall rise and slope, the sloped runs still need the same total horizontal length. Splitting a run adds an intermediate landing and its full flat length to a straight layout.

How do I measure clear width?

Measure the unobstructed usable width, between handrails where provided. Allocate any added room for rails, edges and structural components in your full site plan.

Can I include an existing floor as a landing?

Use the clear space measurement that includes the full area you intend to count as a landing. This model assumes equal clear lengths and widths for all landings. Verify slope and clearances, including those around any doorway, at the actual site.

Does a geometry fit establish ADA compliance?

The geometric fit compares two clear-envelope dimensions. The four listed ADA benchmarks cover individual measures. A full accessibility review also considers the route, landings, surfaces, cross slopes, handrails, edge protections and applicable site requirements.

Similar Calculators