Stair Layout Calculator

Find which stair geometries fit your entered space instead of rounding to a single riser count. Compare straight flights or two flights around a square landing, using uniform finished rise and going. Choose a fitting option to inspect its plan, unfolded profile and tread coordinates; the dimensional result does not assess headroom, structural design or construction approval.

Stair geometry planner

Find a stair layout that fits

Try a layout

Rise and available space

All length fields use millimetres. Valid unit changes preserve physical measurements.

Measure between finished lower and upper floor surfaces.

A square, level landing at least as wide as the stair.

Going and comparison limits

Horizontal distance between successive tread fronts; excludes nosing projections.

Edit riser and going limits

These are your comparison assumptions, not a jurisdiction’s approved dimensions. The preferred riser controls ranking; it is not a safety rating.

Selected layout fits your entered footprint

16 risers · 8 + 8

175 mm rise × 280 mm going

6 fitting options from 65 evaluated layouts. “Fits” is a dimensional result, not construction approval.

Occupied footprint

2,960 mm × 2,960 mm

Pitch of each flight

32.005383°

atan(individual rise ÷ going)

Separate treads

14

Plus one intermediate landing; upper floor is not an extra tread

Space remaining: X / Y

40 mm / 40 mm

This workspace compares finished-surface geometry. It does not check headroom, floor openings, nosings, structural loads, stringer cuts, handrails or building-code requirements.

6 layouts fit. Selected 16 risers with 175 mm rise and 280 mm going.

Compare riser counts and flight splits

Fitting options come first, ordered by closest to your preferred riser, then larger going, more balanced flight split, fewer total risers and fewer first-flight risers. This ranking expresses those criteria only.

Candidate layout ranking and dimensional fit. Lengths in mm. Select a fitting option to update both diagrams and the coordinate ledger.
SelectRisers / splitRise (mm)Going (mm)Footprint X × Y (mm)Fit / constraint
16 / 8 + 81752802,960 × 2,960Fits entered space
15 / 7 + 8186.6666672802,680 × 2,960Fits entered space
15 / 8 + 7186.6666672802,960 × 2,680Fits entered space
14 / 7 + 72002802,680 × 2,680Fits entered space
14 / 6 + 82002802,400 × 2,960Fits entered space
14 / 8 + 62002802,960 × 2,400Fits entered space

Showing 6 of 6 fitting options. CSV includes every evaluated option.

Plan and unfolded profile

Scaled plan — seen from above

Occupied: 2,960 mm × 2,960 mm. Dashed outline: entered available space.

Stair footprint and tread planFirst flight travels along positive X; second travels along positive Y, aligned to the right edge of the square landing. Available footprint is dashed. Equal horizontal and vertical scales. Highlighted: Tread at riser 1 · flight 1. Exact coordinate values are available in the ledger and CSV.X →Y ↑

Flight 1: solid green. Flight 2: dashed blue. Landing: hatched. Purple highlights the selected surface.

Unfolded elevation profile

Rise: 2,800 mm. Horizontal profile: 4,920 mm.

Unfolded stair elevationFinished elevation follows each riser and going, with the square landing side shown between flights. This is not walking distance, stringer length or a cutting template. Equal horizontal and vertical scales. Highlighted: Tread at riser 1 · flight 1. Exact coordinate values are available in the ledger and CSV.Lower floorUpper floor

Both axes use the same scale. The landing is shown by its side length; nosings, materials and floor openings are not modeled.

The upper floor and intermediate landing finish their flights: the 8 / 8 riser flights have 7 / 7 separate goings. The square landing is not counted as another uniform tread.

Every tread and landing

Plan coordinates identify lower-left surface corners, starting at the first riser. The first flight runs along +X; the second along +Y at the right edge of the landing. The upper-floor row is a zero-size reference at the final riser, not a modeled floor area. Lengths below use mm; CSV uses metres.

Selected stair finished-surface coordinates in mm. The highlighted surface matches both diagrams.
SurfaceElevationPlan XPlan YPlan size X × YProfile startProfile end
Tread at riser 1 · flight 1 · highlighted17500280 × 1,0000280
Tread at riser 2 · flight 13502800280 × 1,000280560
Tread at riser 3 · flight 15255600280 × 1,000560840
Tread at riser 4 · flight 17008400280 × 1,0008401,120
Tread at riser 5 · flight 18751,1200280 × 1,0001,1201,400
Tread at riser 6 · flight 11,0501,4000280 × 1,0001,4001,680
Tread at riser 7 · flight 11,2251,6800280 × 1,0001,6801,960
Landing after riser 81,4001,96001,000 × 1,0001,9602,960
Tread at riser 9 · flight 21,5751,9601,0001,000 × 2802,9603,240
Tread at riser 10 · flight 21,7501,9601,2801,000 × 2803,2403,520
Tread at riser 11 · flight 21,9251,9601,5601,000 × 2803,5203,800
Tread at riser 12 · flight 22,1001,9601,8401,000 × 2803,8004,080
Tread at riser 13 · flight 22,2751,9602,1201,000 × 2804,0804,360
Tread at riser 14 · flight 22,4501,9602,4001,000 × 2804,3604,640
Tread at riser 15 · flight 22,6251,9602,6801,000 × 2804,6404,920
Upper floor at riser 162,8001,9602,9600 × 04,9204,920

Geometry, assumptions and sources

For N total risers, every riser is finished rise ÷ N. A flight of n risers has n − 1 separate goings because its final surface is the landing or upper floor. Flight run = (n − 1) × going; pitch = atan(individual riser ÷ going). The profile’s overall diagonal is not used as a stringer cut length.

A straight footprint is flight run × stair width. A quarter-turn footprint is (first run + square landing side) × (second run + square landing side). In inverse mode, each going is the smallest of your maximum going and the available run divided by its going count; the same going is used for both flights. Exact decimal-rational comparisons decide fit and ranking before values are converted for display. No epsilon permits a slightly oversized layout.

Calculations consider 2–80 total risers for straight stairs, or 4–80 for two flights with at least two risers each. Other computational bounds in metres: finished rise 0.1–12; width 0.3–5; each available footprint dimension 0.1–50; riser limits 0.05–0.4; going limits 0.05–1; landing side 0.3–10 and at least stair width. These bounds and illustrative defaults are not construction rules.

Authored millimetre/inch inputs accept six decimal places, including equivalent scientific notation. Unit changes retain canonical measurements while converted display text remains unchanged; editing makes the newly entered text authoritative. Canonical metres support ten decimal places. Very small nonzero residuals use scientific notation. CSV preserves full numeric model output.

Headroom, floor openings, material thickness, nosings, handrails, guards, structural supports, connections, cutting allowances and local approvals require additional project-specific work. The layout only describes dimensions between finished surfaces.

Primary references: OpenStax right-triangle relationships; U.S. Access Board stair measurement and accessibility guidance; AWC deck guide, based on the 2015 IRC. Their requirements have specific application and jurisdiction limits; this tool does not implement or certify either standard.

How to use this calculator

  1. Choose millimetres or US inches, then enter the Finished floor-to-floor rise between finished surfaces. Enter the available plan length X, available plan width Y and stair width using that same unit.
  2. Choose Straight flight or Quarter-turn L with landing. For an L layout, enter a square landing side at least as wide as the stair. The first flight travels along X, and the second turns along Y at the landing’s right edge.
  3. Choose Use my entered going or Find the largest going that fits. Going is the horizontal distance between successive tread fronts. The inverse mode uses one shared going across both flights.
  4. Open Edit riser and going limits to enter your comparison range and preferred riser. These are project assumptions; the initial values are illustrative and are not a building-code selection.
  5. Compare fitting riser counts and flight splits. The order favors the closest preferred riser, then larger going and more balanced flights. Select an option and highlight a surface to connect the plan, unfolded profile and coordinate ledger.
  6. Include options that do not fit to inspect their limiting dimensions. Download or copy the CSV with all evaluated options and the selected coordinates, then verify omitted project requirements separately.

The Formula

The mathematical logic powering this calculation is:

For N total risers: individual riser r = finished floor-to-floor rise / N.
A flight of n risers has n − 1 separate goings because the landing or upper floor is its final surface. Flight run = (n − 1) × going g.
Straight footprint = run × stair width. Quarter-turn footprint = (first run + square landing side) × (second run + square landing side).
Pitch = atan(r / g), not atan(total flight rise / total flight run).
Inverse straight going = min(maximum going, available length / (N − 1)); stair width is checked separately.
Inverse quarter-turn going = min(maximum going, (available length − landing) / (n₁ − 1), (available width − landing) / (n₂ − 1)). A nonpositive or below-minimum going is not an allowed solution.
Riser counts, flight splits, dimensional fit and ranking are compared with exact decimal-rational arithmetic before numerical display. No epsilon admits an oversized footprint.

Worked Example

If you input:

  • Measurement units: Metric — millimetres
  • Layout: Quarter-turn L with landing
  • Going calculation: Use my entered going
  • Finished floor-to-floor rise: 2800
  • Stair width: 1000
  • Available plan length X: 3000
  • Available plan width Y: 3000
  • Minimum riser: 150
  • Maximum riser: 200
  • Preferred riser for ranking: 175
  • Minimum going: 250
  • Maximum going: 350
  • Entered going: 280
  • Square landing side: 1000

Result:

With a 2,800 mm rise, the 16-riser layout has 175 mm per riser. Splitting it into 8 + 8 risers gives seven separate goings per flight. At 280 mm per going, each flight runs 1,960 mm. Adding the 1,000 mm square landing gives a 2,960 × 2,960 mm footprint, fitting within 3,000 × 3,000 mm with 40 mm remaining in each direction. The layout has 14 separate treads, one intermediate landing and the upper-floor reference. Its unfolded profile has 1,960 + 1,000 + 1,960 = 4,920 mm of horizontal geometry; that is not a stringer cut length or a centerline walking-distance estimate.

Frequently Asked Questions

Why is there one fewer separate tread than risers in each flight?

A riser changes elevation, while a going is the horizontal spacing of successive tread fronts. This model treats a landing or the upper floor as the final surface of its flight. A flight with eight risers therefore has seven separate goings before reaching that surface. Two eight-riser flights have fourteen separate treads plus their intermediate landing; the upper floor is a reference point, not an extra tread or modeled floor area.

What does the largest-going mode solve, and when is there no fit?

For each admissible riser count and flight split, the model divides available flight runs by their going counts and applies your maximum-going cap. Both flights use the same resulting going. If the resulting value is below your minimum, the option has no allowed going. Straight-flight width remains a separate check: a going may fit the length while the stair is too wide. No fitting option is selected when all candidates fail.

How is the first fitting layout chosen from the comparison?

Fitting options are ordered by smallest difference from your preferred riser height, then larger going, more balanced flight counts, fewer total risers and fewer risers in the first flight. These are explicit comparison preferences, not a comfort score, safety ranking or approval. You can select another fitting option, and every displayed quantity, diagram and coordinate table updates to that same option.

How are an L-shaped stair and its landing positioned?

The first flight travels in positive X from the origin. The square landing starts at the end of that flight with its lower edge at Y = 0. The second flight travels in positive Y, aligned with the right edge of the landing. Its X origin is first run + landing side − stair width, and its Y origin is the landing side. The plan footprint is first run + landing side by second run + landing side. Winders, spiral stairs and return/U-shaped layouts are not modeled.

Can I use the profile or diagonal as a stringer cutting template?

No. The profile follows ideal finished surfaces and inserts the landing side between flights. It does not include nosing projections, tread or riser material thickness, top and bottom connections, bearing seats, trimming or structural support. Stair pitch uses individual riser divided by going; the overall floor-to-floor diagonal has different endpoints and is not a stringer cut length.

Does a fitting layout satisfy headroom or building-code requirements?

No. Fits means that the modeled footprint stays within the dimensions you entered and that the option meets your riser/going comparison limits. Headroom depends on ceilings and floor openings that are not entered. The model also excludes structural capacity, guards, handrails, nosing rules and jurisdiction-specific requirements. The linked Access Board and AWC references have specific scopes; this calculator does not implement or certify those standards.

What happens to my measurements when I switch between metric and US units?

All fields use millimetres in metric mode or inches in US mode; US fields are not decimal feet. A valid switch preserves canonical measurements even if a converted display is rounded. Editing a field makes its newly entered text authoritative. Required blanks prevent calculations and unit switching instead of becoming zero. Inactive entries are retained when modes change. CSV records canonical metre values and full numeric model output.

What numerical limits and precision does the planner support?

Straight flights consider 2–80 total risers. Quarter-turn layouts consider 4–80 with at least two risers per flight. Supported metres are: total rise 0.1–12, stair width 0.3–5, footprint dimensions 0.1–50, riser limits 0.05–0.4, going limits 0.05–1 and landing side 0.3–10. The landing must be at least stair width. Authored mm/inch measurements allow six decimal places and equivalent scientific notation; canonical metres allow ten. These are computational bounds, not recommended construction dimensions. Exact fit comparisons do not silently round an overrun into a fit.

Similar Calculators