Spray Foam Thickness, Yield & Quote Planner
Use the same measured zones and target depths to compare two spray foam proposals. See which zone falls below the required depth, even when total board feet exceed the target. Check the minimum yield for a recorded kit count using an independently entered planning range. Compare written installation, preparation and access costs separately.
Compare spray foam depth, yield and quotes
Check each stated zone depth, reconcile board feet against entered kit assumptions, and compare independently priced installation scope.
Depth scope and installed quote
Proposal A
- Required volume
- 880 BF
- Proposed volume
- 960 BF
- Local depth gap
- 40 BF
- Written quote
- $1,920.00 known
Proposal B
- Required volume
- 880 BF
- Proposed volume
- 880 BF
- Local depth gap
- 0 BF
- Written quote
- $1,928.00
At least one proposal misses an entered zone depth. Review scope before comparing complete prices.
Edit zone measurements and proposals
Measured zones and required depth
Use measured areas along the surfaces receiving foam, including slopes. Enter a separate excluded area if the reported measurement includes parts outside the written scope.
Zone 1
Zone 2
Proposal A
Proposal A proposed depths
Proposal A kit inventory and planning yield
Use one homogeneous kit label and entered effective yield estimates from your planning records. Commercial installation quotes can leave this audit off.
Proposal A written quote
Proposal B
Proposal B proposed depths
Proposal B kit inventory and planning yield
Use one homogeneous kit label and entered effective yield estimates from your planning records. Commercial installation quotes can leave this audit off.
Proposal B written quote
Zone-by-zone thickness comparison
The vertical mark is the required depth for that zone. Bars share a common inch scale. Extra foam in one measured zone cannot fill a depth gap in another.
Proposal A
Roof deck · 240 ft²
0.5 in over · 120 BF above target
Rim area · 80 ft²
0.5 in short · 40 BF below target
1 zone misses the entered depth.
Proposal B
Roof deck · 240 ft²
Matches entered depth
Rim area · 80 ft²
Matches entered depth
All zones meet entered depths.
Kit inventory and effective yield
The range uses your entered effective percentages of the theoretical label. The vertical mark shows the minimum effective yield for the recorded kit count and proposed volume.
Proposal A
2 kits · 600 BF theoretical per kit
- Minimum yield needed
- 80%
- Whole kits across yield range
- 2 to 3
- Lower modeled supply
- 780 BF
- Upper modeled supply
- 1,020 BF
Entered range 65% to 85%.
Meets the volume at the upper bound and falls short at the lower bound.
Shortage at lower yield 180 BF.
Proposal B
6 kits · 200 BF theoretical per kit
- Minimum yield needed
- 73.333333%
- Whole kits across yield range
- 5 to 6
- Lower modeled supply
- 900 BF
- Upper modeled supply
- 1,080 BF
Entered range 75% to 90%.
Meets volume at both yield bounds.
Written quote ledger and export
Installation uses your entered price basis. Included means no incremental price. Kit counts and yield assumptions add no costs to this ledger. BF means board feet.
Proposal A
- InstallationPer board foot
- $1,920.00
- Preparation
- Unpriced
- Site access
- Included
- Other written charges
- Included
- Known subtotal
- $1,920.00
- Complete total
- Incomplete
Proposal B
- InstallationPer board foot
- $1,848.00
- Preparation
- $80.00
- Site access
- Included
- Other written charges
- Included
- Known subtotal
- $1,928.00
- Complete total
- $1,928.00
Show selectable CSV text
Use the professionally specified depth and documented written scope. This worksheet compares dimensions, entered yield assumptions and charges. It does not determine product choice, thermal rating, installation or occupancy conditions.
How to use this calculator
- Enter each measured surface and any excluded area. Enter the required depth from the documented scope.
- Enter each proposal's measured or quoted depth for every zone. Compare the local thickness marks, required volume and any uncovered work.
- For a kit-based proposal, record the theoretical label yield, kit count and independently specified lower and upper planning percentages.
- Enter written installation prices and preparation, access and other charges. Check the basis stated in each quote.
- Review the depth and yield decisions separately from complete costs. Download the reconciled worksheet as CSV.
The Formula
The mathematical logic powering this calculation is:
For each zone, subtract the excluded area from the measured area. Use the surface's actual area. Multiply by the entered required or proposed depth in inches to obtain board feet, where one board foot is one square foot at one inch thick. Summing measured volumes gives total required and proposed board feet. For each below-target zone, multiply its missing depth by the net area. The sum of those positive local shortfalls stays separate from over-target volume in other zones.
Each optional kit audit uses one homogeneous label yield in board feet per kit, one recorded count, and entered lower and upper effective planning percentages. Modeled volume equals kit count times label yield times each percentage as a fraction. The minimum effective percentage equals 100 times proposed board feet divided by theoretical board feet for the recorded kit count. With positive planned volume and no kits, that percentage is unavailable. A value above 100% exceeds the entered theoretical reference for that count. Favorable and conservative whole-kit requirements divide the proposal volume by each entered effective yield per kit and round up. Zero effective yield gives no finite kit count for positive planned volume. These are arithmetic scenarios based on your inputs. Published theoretical yields come from controlled conditions and cannot establish field volume.
Written installation may use one fixed amount, a rate per proposed board foot, or a rate per measured net square foot in zones receiving some proposed depth. Multiply the entered rate by its stated basis and round to the nearest cent with half-cent ties upward. Add quoted preparation, site access and other written charges. Included records no incremental price. Unpriced or invalid lines keep a known subtotal and leave the full comparison unavailable. The kit audit does not add any charges.
Enter 1–8 named zones. Positive net area uses hundredths of a square foot, up to 100,000 ft² per zone. Depths use hundredths of an inch up to 24 in. The shared required depth must be positive. A zero proposed depth omits that zone. Effective yield percentages are entered to hundredths between 0 and 100. Kit counts use whole numbers. Example kit references are the 200 BF and 600 BF theoretical labels listed in the source, and all example prices, depths and yield percentages are illustrative.
This worksheet evaluates the entered quote and dimensional scope. Product choice, code, thermal performance, work conditions and actual installation suitability require their own project review.Worked Example
If you input:
- Roof deck: 240 ft² net, required depth 3 in. Proposal A 3.5 in. Proposal B 3 in.
- Rim area: 80 ft² net, required depth 2 in. Proposal A 1.5 in. Proposal B 2 in.
- Entered kit assumptions: A records two 600 BF labels at 65–85% planning yield. B records six 200 BF labels at 75–90%.
- Written charges: Illustrative rates $2 and $2.10 per board foot. A preparation is unpriced. B separately prices it at $80.
Result:
The total target is 880 board feet. Proposal A provides 960 board feet overall with a 40-board-foot shortage in the rim zone. It requires 80% effective yield at its recorded kit count and has $1,920 in known charges. Proposal B meets both entered depths, has a threshold of about 73.333333%, and has a complete $1,928 quote.
Frequently Asked Questions
What is a board foot of spray foam?
It is a quantity of volume equal to one square foot at one inch thick. Multiply net square feet by entered depth in inches.
Can total board feet be enough while a zone is short?
Yes. Compare thickness by zone. An extra half inch in one area does not contribute to another zone's missing depth.
How do I estimate actual kit yield from the theoretical label?
Use an independently documented planning range. The worksheet calculates the resulting volumes and reports the effective percentage that the recorded kit count would require. The label is a reference, and field output can vary.
What changes when a proposal does not use kits?
Turn off its optional kit audit. The measured zone scope and entered installed quote remain available.
What happens when the lower effective yield is zero?
Positive planned volume cannot be met with any finite number of kits at zero yield. The upper yield can still give a favorable kit count when it is positive.
Will this tell me what depth or product to use?
Enter the agreed project requirements and actual documented proposal. The worksheet compares those values and does not select materials, predict R-values or approve the work.
Similar Calculators
Insulation Calculator & Package Cost Planner
Plan insulation quantities across zones, compare compatible package sizes and blown-material label limits, and visualize pooled purchasing savings, overage and project costs.
Floor-Leveling Compound Depth & Bag Planner
Estimate self-leveling compound from measured floor elevations. Compare finish heights, buildup limits, geometric volume, whole bags and material costs.
Room Heat Loss & Retrofit Calculator
Explore room heat loss and sensible cooling, compare envelope and ventilation retrofits, and visualize heat flows and outdoor-temperature sensitivity with exact CSV ledgers.
Crawl Space Encapsulation Cost & Liner Planner
Calculate crawl space liner area and compare encapsulation quotes. Count overlapping floor bays once, measure wall liner and estimate whole rolls or installed costs.
