Speaker Impedance & Amplifier Load Planner

Compare two arrangements of passive speaker cabinets. Group cabinets in series within a branch and combine branches in parallel. Use nominal labels alone or enter real and reactive impedance readings at shared frequencies. The plots and ledger report pointwise magnitude and phase, current at an ideal entered RMS source, and average real power.

Passive speaker load planning

Compare speaker layouts and impedance

Compare nominal labels and complex load samples. Inspect magnitude, phase and ideal source power at the entered frequencies.

Nominal and sampled loads

Nominal reference 4 Ω · Sampled magnitude guide 4 Ω

Layout A

4 Ω

Nominal equivalent · At nominal reference

Lowest entered-frequency magnitude
3.162 Ω at 200 Hz · 18.435° phase
Samples below guide
2 of 4

Layout B

16 Ω

Nominal equivalent · Above nominal reference

Lowest entered-frequency magnitude
12.166 Ω at 1,000 Hz · 9.462° phase
Samples below guide
0 of 4

The comparisons describe the entered model and samples. Amplifier suitability and loads between samples require separate evidence.

Speaker labels and references

Edit layout branches

Cabinets within each branch are in series. The branches form a parallel load on one ideal source.

Layout A
Branch 1
Branch 2
Layout B
Branch 1
Edit shared impedance samples

Use matching frequencies for both active cabinet types. Enter R and signed X from the same measurement basis.

Sample 1
Sample 2
Sample 3
Sample 4

Measured-frequency load comparison

Each marker represents one entered frequency. Frequency and magnitude use logarithmic scales.

Layout ALayout B

Impedance magnitude (Ω)

Impedance magnitude (Ω)Layout A 4 Ω at 100 Hz, 3.162 Ω at 200 Hz, 5 Ω at 400 Hz, 3.288 Ω at 1,000 Hz. Layout B 16 Ω at 100 Hz, 12.649 Ω at 200 Hz, 16 Ω at 400 Hz, 12.166 Ω at 1,000 Hz.163.162100 Hz1,000 Hz

Dashed line marks the 4 Ω magnitude guide.

Impedance phase (degrees)

Impedance phase (degrees)Layout A 0° at 100 Hz, 18.435° at 200 Hz, 0° at 400 Hz, -9.462° at 1,000 Hz. Layout B 0° at 100 Hz, 18.435° at 200 Hz, 0° at 400 Hz, 9.462° at 1,000 Hz.90−90100 Hz1,000 Hz

Dashed line marks 0° phase.

Show layout and sample ledger

Layout A

  • Branch 1 · 1 × Cabinet 1
  • Branch 2 · 1 × Cabinet 2

Layout B

  • Branch 1 · 1 × Cabinet 1 in series with 1 × Cabinet 2

Layout A

3 + j1 Ω · 3.162 Ω · 18.435°

2.53 A RMS · 19.2 W average real power

Below sampled magnitude guide

  • Branch 1 · 6 + j2 Ω · 1.265 A RMS · 9.6 W
  • Branch 2 · 6 + j2 Ω · 1.265 A RMS · 9.6 W

Layout B

12 + j4 Ω · 12.649 Ω · 18.435°

0.632 A RMS · 4.8 W average real power

Above sampled magnitude guide

  • Branch 1 · 12 + j4 Ω · 0.632 A RMS · 4.8 W

Export speaker load comparison

Download speaker load CSV
Show selectable CSV

How to use this calculator

  1. Choose Parallel vs series samples or Four nominal cabinets. Enter the nominal label of each cabinet type used and a separate nominal reference.
  2. Open Edit layout branches. Enter the number of each cabinet type in series within a branch. Use multiple branches to model a parallel arrangement.
  3. Choose Measured frequency points for shared R and signed X data. Enter the same measured frequency for both cabinets within a row, along with the ideal-source calculation voltage and separate magnitude guide. Enter zero voltage to hold ideal source current and power at zero.
  4. Review nominal and sampled outcomes. Switch the inspected frequency in the layout and sample ledger to read the source and branch values.
  5. Export the topology, samples and calculated values as a CSV.

The Formula

The mathematical logic powering this calculation is:

For nominal labels, each branch’s impedance is the sum of entered label ohms of its cabinets. Combined equivalent is 1 divided by the sum of reciprocals across parallel branches. Compare that nominal equivalent with the user-entered nominal reference. This arithmetic uses label values and does not assume a frequency response.
At each supplied frequency, cabinet Z = R + jX, with positive R and signed X. Add R and X separately across series cabinets in each branch. Each branch admittance is 1/Z = (R − jX)/(R² + X²). Sum admittances across the parallel branches and invert that sum to obtain the equivalent complex impedance. Magnitude is the square root of Re(Z)² + Im(Z)². Phase is atan2(Im(Z), Re(Z)) in degrees, describing voltage phase relative to current. Opposing reactances can cancel in series. In parallel the cancellation depends on the imaginary admittances.
The sampled magnitude guide is separate from the nominal reference. Threshold comparisons and the sampled minimum use exact rational comparisons of magnitude squared at the entered precision. Results and charts display floating-point approximations. When sampled minima tie, the ledger identifies the lower frequency. The plot places points only at supplied frequencies on a logarithmic frequency scale. Magnitude uses a log scale and phase a linear scale. Behavior between samples is undetermined.
At the ideal entered Vrms, source current magnitude is Vrms divided by |Z|. Average real power is Vrms² × Re(1/Z). For a branch, use its own complex impedance with the same Vrms. Branch real powers add to source real power. These are ideal voltage-source calculations for one frequency at a time. They do not model amplifier limits, bridging, output impedance, power rating, clipping, sound level or thermal performance.
Each layout supports 1–4 parallel branches with 0–8 of each of two cabinet types in a branch and at least one cabinet per branch. Nominal, guide and real impedances are 0.1–500 Ω. Reactance accepts −500 to +500 Ω and ideal voltage 0–200 Vrms. Use 1–8 distinct frequencies from 10–40,000 Hz, with matching measurements for each active cabinet type. Input quantities accept up to three decimal places and counts are whole numbers. The example readings are illustrative.
The worksheet compares nominal and measured numbers only. Equipment suitability requires published conditions for the actual amplifier and mode, supported loads and the behavior of the actual speakers.

Worked Example

If you input:

  • Cabinet labels: 8 Ω each. Nominal reference 4 Ω.
  • Layout A: One cabinet of each type in two parallel branches
  • Layout B: One cabinet of each type in a single series branch
  • Measured-frequency assumptions: Four illustrative samples from 100–1,000 Hz. At 200 Hz both cabinet readings are 6 + j2 Ω. Sampled guide 4 Ω.
  • Ideal source: 8 Vrms

Result:

The nominal equivalents are 4 Ω for Layout A and 16 Ω for Layout B. At 200 Hz Layout A reduces to 3 + j1 Ω, about 3.162 Ω magnitude, 18.435° phase, and 19.2 W average real power at the entered voltage. This is the lowest of Layout A’s four entered-frequency magnitudes. Layout B’s lowest sampled magnitude is about 12.166 Ω at 1,000 Hz.

Frequently Asked Questions

What is the impedance of two 8-ohm speakers in parallel?

Two ideal 8 Ω nominal labels in parallel give 4 Ω nominal arithmetic. Actual measured impedance depends on frequency. The sampled mode requires real and reactive values for each active cabinet at the same frequencies.

Why can a layout labeled 4 Ω be lower at one frequency?

Nominal labels summarize a speaker’s load for a product specification. Real and imaginary impedance change with frequency. The sampled plot compares computed magnitudes at the entered measurements separately from the nominal value.

What does negative phase mean?

Phase is the angle of equivalent impedance, which gives voltage phase relative to current. Negative phase corresponds to net negative reactance, with current leading voltage in this model.

Can I enter 0 Ω measured resistance?

Enter positive real impedance for every measured cabinet, with zero allowed for reactance. This planner models passive cabinet loads with nonzero real part.

Does current or power match an amplifier rating?

The worksheet computes ideal steady RMS current and average real power at the voltage you enter, one sampled frequency at a time. Published ratings depend on the actual equipment, configuration, load and test conditions.

Does the minimum include between-frequency dips?

The sampled minimum covers the entered points. Add measurements where you need finer coverage. Neither a predicted response between points nor a suitability verdict is inferred.

Similar Calculators