Soil Texture Triangle & Dry-Mass Blend Planner

Compare two tested mineral soil sources and two proposed dry-mass blends. The USDA texture triangle shows both sources and every texture class crossed by their mixing line. Pick a target class to see the exact blend interval and the dry mass of each source needed for your batch.

Soil worksheet

Compare soil textures and dry-mass blends

Plot two measured sources, compare two blend ratios and find the dry mass range for a target USDA texture.

Loam is possible with the shares below.

Loam dry-share range

  • [45%, 85%) from Source B

    Source A (15, 55] kg · Source B [45, 85) kg

A square bracket includes its endpoint. A round bracket excludes it.

Blend 1 · 50% from B
Loam
50 kg from A · 50 kg from B
Blend 2 · 85% from B
Clay loam
15 kg from A · 85 kg from B
Source A

Enter dry mineral fine-earth percentages that total 100%.

Source B

Enter dry mineral fine-earth percentages that total 100%.

Dry batch and target

Enter 0.001 to 100,000 kg or lb and include the unit, such as 100 kg.

Enter 0–100%. The remaining share comes from Source A.

Enter 0–100%. The remaining share comes from Source A.

USDA texture triangle
Dry soil source and blend compositionsSand increases toward the bottom left, silt toward the bottom right, and clay toward the top. Source A is Sandy loam. Source B is Clay loam. The selected class is Loam. Exact class boundaries and the two blends are in the ledger.100% clay100% sand100% silt
  • Source A
  • Source B
  • Blend 1
  • Blend 2
  • Blend ratios for loam

Grid lines are 20 percentage points apart. The dashed line connects the sources. Green highlights blends in the chosen class. A filled endpoint is included and a hollow endpoint is excluded.

Open composition and class ledger

Percentages and converted weights are rounded for display. Endpoint classification uses exact values.

Soil percentages and source weights in both units
SpecimenTextureSand %Silt %Clay %Dry masses
Source ASandy loam702010—
Source BClay loam304030—
Blend 1Loam50302050 kg A / 50 kg B · 110.2311 lb A / 110.2311 lb B
Blend 2Clay loam36372715 kg A / 85 kg B · 33.0693 lb A / 187.3929 lb B

Texture changes along the mixing line

USDA class intervals as fractions of the dry batch supplied by B
TextureB shareExact B lowerExact B upper
Sandy loam[0%, 45%)0/1 · included9/20 · excluded
Loam[45%, 85%)9/20 · included17/20 · excluded
Clay loam[85%, 100%]17/20 · included1/1 · included

Exact target dry masses

  • [45%, 85%) from B · Source A 15/1 through 55/1 kg · Source B 45/1 through 85/1 kg
Download soil blend CSV
Show selectable CSV

How to use this calculator

  1. Enter sand, silt and clay from a test of each dry fine-earth source. The three percentages must total 100% per source.
  2. Enter a batch dry mass with kg or lb, then enter the share of that mass supplied by Source B for each proposed blend.
  3. Choose a target USDA class. Compare the proposed blends with the feasible share range and both source masses. Square brackets include an endpoint and round brackets exclude it.
  4. Inspect the shared triangle and open the ledger for the exact boundaries, then download the CSV if you need to keep the calculation.

The Formula

The mathematical logic powering this calculation is:

Report sand, silt and clay as percentages of dry mineral fine earth under 2 mm. Each source must add to exactly 100%. With B contributing fraction x of the total dry mass, each blended percentage is (1 − x) × Source A percentage + x × Source B percentage. A and B dry masses are (1 − x) × batch and x × batch in the entered unit. The equivalent mass uses 1 avoirdupois pound = 0.45359237 kg.

Classification uses the twelve general texture conditions in the USDA NRCS workbook, CalcCode cells A2 through A13. For example, loam requires at least 7% and below 27% clay, at least 28% and below 50% silt, and no more than 52% sand. Every comparison becomes a linear bound on x. Intersect the bounds with the possible range from 0 to 1. If more than one branch applies to a class, join only connected intervals. A closed interval can reduce to one precise share. Triangle outlines show geometry while exact endpoint ownership is recorded in the ledger and CSV.

Composition percentages and blend shares allow up to four decimals. Batches range from 0.001 to 100,000 kg or lb with up to three decimals. Endpoint inclusion follows the supplied values before rounding. An approximate displayed bound has an exact fraction in the ledger. The model combines the measured fine-earth fractions of the two inputs and assumes no constituent loss.

Worked Example

If you input:

  • Source A sand, silt, clay: 70%, 20%, 10%
  • Source B sand, silt, clay: 30%, 40%, 30%
  • Batch dry mass: 100 kg
  • Blend 1 and 2 dry share from Source B: 50% and 85%
  • Target texture: Loam

Result:

Blend 1 uses 50 kg of each source and gives 50% sand, 30% silt and 20% clay, which is loam. Loam is possible from 45 kg of Source B inclusive through 85 kg exclusive. Exactly 85 kg gives 36% sand, 37% silt and 27% clay, so Blend 2 is clay loam.

Frequently Asked Questions

What soil fractions go into the USDA texture triangle?

Use sand, silt and clay percentages measured for the dry mineral fine-earth fraction below 2 mm. The twelve general class names omit sand-size subdivisions and rock-fragment modifiers.

Why does the worksheet use dry mass?

The percentages refer to dry material. Water or coarse fragments in a bulk weight can affect the actual fine-earth proportions mixed. Mass per bucket also varies with packing density.

Why can a texture require exactly one proportion?

A line between the two sources can touch a corner of a target class at one point. The result is usable only if the class owns that exact point under all of its inequalities.

What do open and closed endpoints mean?

At an included endpoint the exact blend qualifies. An excluded endpoint marks where a neighboring class starts. Read the exact fractions for boundaries marked approximate to avoid comparing rounded displays.

Why do both mixes sometimes appear at the same point?

Different quantities can have identical percentages. If the two source compositions match, every blend lies at that same location and has the same general class.

Does texture tell me which blend will work for my site?

Texture is one measured property. The worksheet gives a composition and class. Site performance depends on other factors such as aggregation, organic matter, mineralogy, compaction and drainage.

Similar Calculators