Soffit Panel & Fascia Takeoff Planner

Plan the pieces that cover straight eaves. Compare two products by effective panel width, usable stock length, shared offcuts, whole packs, and separately quoted fascia and receiver runs. See where each cut comes from and how the material and labor prices add up.

Measured eaves and whole stock

Compare soffit panel cuts and fascia quotes

Example dimensions, stock and prices are illustrative. Use measurements and quotes for your own project.

Offer A

$315.00

Panels in layout
4
Packs ordered
4
Full-width strips
24
Spare whole panels
0

Offer B

$313.00

Panels in layout
3
Packs ordered
3
Full-width strips
20
Spare whole panels
0

33.333 ft² measured soffit · 16 ft fascia · 40 ft receivers

Offer B is $2.00 lower for the entered scope.

Offer A $315.00. Offer B $313.00. Offer B is $2.00 lower for the entered scope.

Eave profile and strip coverage

Front eave · 120 in along eave · 18 in deep · 15 ft²

Offer A eave coverage
Offer A requires 12 strips. The final strip covers 10 in along the eave.
Planned strips
12
Cut length along stock
18 in
Final visible width
10 in
Trimmed from final width
0 in

The shaded strip shows the final visible face.

Offer B eave coverage
Offer B requires 10 strips. The final strip covers 12 in along the eave.
Planned strips
10
Cut length along stock
18 in
Final visible width
12 in
Trimmed from final width
0 in

The shaded strip shows the final visible face.

Stock panel cut order

Each cut reserves the full stock face. The layout fits the longest cuts first and uses the existing panel with the least space left after each cut.

Offer A

Proven minimum under this policy · 4 stock panels

Required cut length
480 in
Gaps between cuts
0 in
Remaining length on cut panels
96 in
Total panels purchased
4

Stock may be shared across eaves.

Panel 1 · 144 in usable length
Panel 1 uses 132 in, including 0 in between cuts, with 12 in remaining.
  1. Rear eave · 6 cuts × 22 in

0 in gap loss · 12 in remains at the end

Offer B

Proven minimum under this policy · 3 stock panels

Required cut length
400 in
Gaps between cuts
0 in
Remaining length on cut panels
32 in
Total panels purchased
3

Stock may be shared across eaves.

Panel 2 · 144 in usable length
Panel 2 uses 142 in, including 0 in between cuts, with 2 in remaining.
  1. Rear eave · 4 cuts × 22 in
  2. Front eave · 3 cuts × 18 in

0 in gap loss · 2 in remains at the end

Edit measured eaves and trim

Measure length and depth on the plane to be covered. Enter the separate fascia and receiver lengths from your measured scope. Use 0 for an excluded line.

Eave 1 · Front eave
Eave 2 · Rear eave
Edit Offer A stock and prices
Panel sizes and cutting policy

Enter the installed face the panel covers along the eave.

Added to the measured depth. Enter a negative number for a shorter cut.

Space used only between cut pieces on the same panel.

Enter 1 when priced per panel.

Entered quote prices
Edit Offer B stock and prices
Panel sizes and cutting policy

Enter the installed face the panel covers along the eave.

Added to the measured depth. Enter a negative number for a shorter cut.

Space used only between cut pieces on the same panel.

Enter 1 when priced per panel.

Entered quote prices
Show strip and cost ledgers
Measured eave strip count by offer
EaveOffer AOffer B
Front eave15 ft²12 strips18 in cut · 10 in last face10 strips18 in cut · 12 in last face
Rear eave18.333 ft²12 strips22 in cut · 10 in last face10 strips22 in cut · 12 in last face
Soffit, fascia and receiver quote costs
Cost lineOffer AOffer B
Ordered soffit stock$76.00$72.00
Measured fascia$64.00$72.00
Measured receivers$50.00$44.00
Soffit area labor$100.00$105.00
Other entered costs$25.00$20.00
Entered total$315.00$313.00

Export results

Download soffit comparison CSV
Show selectable CSV text

How to use this calculator

  1. Enter the covered length and depth of each measured straight eave. Enter independently measured fascia and receiver lengths using inches.
  2. Enter the installed face width, usable stock length, cut offset and gap for each offer. Use measurements or the product specifications.
  3. Choose whether an offer can reuse the same stock across eaves. Inspect strip widths and the stock panel cut sequence for each offer.
  4. Enter the price per pack, fascia and receiver rates, labor per actual soffit area and any fixed written costs. One panel per pack models individual pricing.
  5. Compare whole packs and complete entered costs. Download the measured schedule, cost lines and stock cuts as CSV.

The Formula

The mathematical logic powering this calculation is:

Measure each straight rectangular eave on the plane to be covered. With measured length L and depth D in inches, area is L × D ÷ 144 square feet. Enter the effective face width W across the length of the eave. The number of full-width cut pieces is ⌈L/W⌉. The last piece covers L − (count − 1)W inches and can lose W minus that width across its face. Even a narrow final strip reserves a full-width stock cut. The model does not reuse its narrow side trim.

Each piece uses D plus the signed cut offset in the stock length direction. The same offset is used for all eaves in an offer. The resulting cut must be positive and no greater than the usable stock length. The entered cut gap consumes space between adjacent pieces on the same stock panel. Account for any required stock-end allowances before entering usable length.

Cut groups are considered from longest to shortest. Put each cut in the tightest existing stock panel it can fit. Start a new panel when none can receive it. Disabling shared stock repeats the policy independently per eave. Within each group of shared stock, a lower bound uses the total weighted length and counts of pieces at every minimum cut length. The weighted calculation treats each cut as its length plus one gap and each stock panel as its length plus one gap, so gap charges apply only between pieces. A matching lower bound proves the displayed stock count under the selected reuse rule. A higher feasible count remains a usable cut plan with the minimum undetermined.

Packs ordered are the planned stock panels divided by panels per pack, rounded up. Total cost adds pack cost, measured fascia feet times its quoted rate, measured receiver feet times its quoted rate, measured soffit square feet times the labor rate, and entered fixed costs. Each line is rounded to cents, with half cents upward. The example prices and product offers are illustrative. Enter all costs in USD and record separately quoted footage from the job scope.

The model supports one to ten independent straight eaves and at most 360 planned strips per offer. Eave length is .001–2,400 in and depth .001–144 in. Separately measured fascia and receiver runs are 0–7,200 in each per eave. Product face width is 1–36 in, usable stock 1–240 in, cut offset −12 to 12 in, gap 0–2 in, and pack size 1–200 panels. Measurements accept up to three decimals and prices accept cents. The calculator does not determine ventilation capacity, structural attachment, span, or corner cuts.

Worked Example

If you input:

  • Front eave: 120 in long × 18 in deep. Enter 120 in of fascia and 240 in of receivers.
  • Rear eave: 120 in long × 22 in deep. Enter 72 in of fascia and 240 in of receivers.
  • Offer A stock: 10 in effective face, 144 in usable stock, zero cut offset and gap, shared stock, one panel per $19 pack.
  • Offer B stock: 12 in effective face, 144 in usable stock, zero cut offset and gap, shared stock, one panel per $24 pack.
  • Offer A other costs: $4/ft fascia, $1.25/ft receivers, $3/ft² labor and $25 fixed.
  • Offer B other costs: $4.50/ft fascia, $1.10/ft receivers, $3.15/ft² labor and $20 fixed.

Result:

The project has 33⅓ ft² of soffit, 16 ft of entered fascia and 40 ft of entered receivers. Offer A needs 24 strips from four stock panels and totals $315.00. Offer B needs 20 strips from three stock panels and totals $313.00. Separating its stock by eave requires four stock panels and raises Offer B to $337.00.

Frequently Asked Questions

Why is my cut count different from dividing the eave area by panel area?

The installed face width determines how many strips cover the eave. Measured depth and the selected offset determine each cut length. A surface-area division cannot show whether the individual cuts fit the usable stock.

What is effective face width?

It is the width one installed strip covers along the eave. Enter the covered width of the selected product and leave interlocking or concealed widths outside that measurement.

Does a narrow last strip use a whole cut?

Yes. The worksheet reserves one full-width cut and shows the part removed across its face. It excludes that narrow trim from usable stock for the other cuts.

Is the plan guaranteed to use the fewest panels?

The chart identifies a proven minimum when the displayed feasible layout reaches the lower bound. When the count is larger than the bound, use the shown layout and review whether a different cut sequence offers more reuse.

Why can I order more panels than the layout needs?

Panels are bought in complete packs using the entered pack size. Spare whole panels remain in the stock ledger alongside the remaining length on cut panels.

How do I include fascia or the channels at the eave edges?

Enter the separately measured footage as inputs and use the corresponding rate in each offer. The calculator uses the entered lengths directly. Enter zero length or a zero rate for an excluded line.

Does the calculator size vented soffit?

Its scope is measured material and cost. Use the related roof ventilation worksheet for an entered net free area comparison.

Similar Calculators