Pipe Weight Calculator & Contents Planner

Build a list of measured pipe lengths and compare two material or schedule options. Use wall dimensions and material density to estimate dry pipe weight, or enter the mill’s listed dry mass per length. Add known hardware separately, then choose a liquid depth for each level run. The cutaway shows how much of the bore the liquid occupies, and the weight bars and ledger reconcile every component.

Pipe and fittings

Compare empty and filled pipe weights

Compare two pipe specifications over the same measured runs and inspect the mass of the wall, liquid and fittings.

Empty, loaded and full weight

Option B weighs 55.72 lb more at the entered depth.

Option A

184.31 lb loaded

155.22 lb empty213.41 lb full

Dry pipe
146.40 lb
Accessories
8.82 lb
Liquid at depth
29.09 lb

Option B

240.03 lb loaded

214.43 lb empty265.63 lb full

Dry pipe
201.20 lb
Accessories
13.23 lb
Liquid at depth
25.60 lb

The dark tick shows each full-bore total on the shared scale.

Run measurements and material

Option A specification
Option B specification

Inspect the bore at the entered depth

Option A
Outside diameter
2.375 in
Bore diameter
2.067 in
Liquid depth
1.034 in
Bore volume filled
50%
Option B
Outside diameter
2.375 in
Bore diameter
1.939 in
Liquid depth
0.969 in
Bore volume filled
50%

Pipe weight ledger

Mass by measured run and option, with accessories counted in the comparison totals.
Run and optionLengthDry pipeLiquid at depthLoaded pipeFull pipe
Horizontal transfer line · Option A40.00 ft146.40 lb29.09 lb175.49 lb204.59 lb
Horizontal transfer line · Option B40.00 ft201.20 lb25.60 lb226.80 lb252.41 lb
Download pipe weight CSV
Show selectable CSV data

How to use this calculator

  1. Start with the published Schedule 40 versus Schedule 80 example or the measured-quarter-depth comparison.
  2. Enter one line for each distinct pipe geometry, fill depth or run length. Set equal lengths and counts across the options to compare the same scope.
  3. Enter actual outside diameter and wall thickness for both options. Choose either material density or the listed dry mass per length for each.
  4. Use one entered liquid density. Enter depth from the bottom as a percentage of internal diameter, and add accessory mass separately for each option.
  5. Read the dry, loaded and full amounts. Inspect a named run in the cross-section and download the ledger for the complete comparison.

The Formula

The mathematical logic powering this calculation is:

Use actual outside diameter D and wall thickness t, so bore d = D − 2t. The annular wall area is πt(D − t). For a uniform wall density ρw, dry mass per length is wall area × ρw using compatible units. Alternatively, use the entered listed dry mass per length. Multiply by length per piece × piece count. Enter only accessory mass beyond what the selected dry mass includes.

The model assumes a straight, level, round bore with uniform liquid depth across its length. At the filled depth fraction f, wetted central angle θ = 4asin(√f) in radians and the bore volume fraction is (θ − sin θ)/(2π). The calculation uses a shallow-cap series at tiny f and its complement above mid-depth. Height fraction and volume fraction coincide at 0%, 50% and 100%. Full volume is πd²/4 × installed length. At-depth liquid mass is full volume × volume fraction × liquid density. Use actual density at the relevant conditions. The worked example uses an entered 1,000 kg/m³.

Empty total includes all dry pipe and entered accessories. Loaded total adds at-depth liquid mass. Full total adds full-bore liquid mass. Reported pounds and kilograms are units of mass. The display uses up to three decimals for diameters and liquid depth and two decimals for other quantities, with scientific notation for small nonzero results. CSV uses unrounded model values and named SI columns. The unit conversions use 25.4 mm per inch, 0.3048 m per foot, 0.45359237 kg per pound and 3.785411784 litres per US gallon.

Enter 1–24 groups, 1–100,000 pieces per group, 0.001–100,000 m per piece, 0.03–10,000 mm outside diameter and 0.001–5,000 mm wall thickness below half the outside diameter. Mass density is 1–30,000 kg/m³, listed mass is 0.000001–3,000,000 kg/m, accessories per option are 0–100,000,000 kg, and liquid depth is zero or 0.000001–100% of bore height. Values in US units are converted to these bounds. The estimate excludes changes from slope, flowing or sloshing liquid, flexible wall deformation and any coatings, couplings, insulation or equipment mass omitted from the entries. Lifting capacity, transport limits, pressure rating and support spans require their own assessment.

Worked Example

If you input:

  • Measured scope: Two 20 ft lengths at half of internal diameter
  • Schedule 40: 2.375 in OD, 0.154 in wall, 3.66 lb/ft plain end
  • Schedule 80: 2.375 in OD, 0.218 in wall, 5.03 lb/ft plain end
  • Liquid and accessories: 1,000 kg/m³ liquid, separate 4 kg and 6 kg accessory assumptions

Result:

With the entered accessories and half-depth liquid, Schedule 40 weighs 184.31 lb and Schedule 80 weighs 240.03 lb. The heavier wall increases dry mass and reduces full-bore capacity. The two loaded options differ by 55.72 lb.

Frequently Asked Questions

Which diameter do I enter for a nominal two-inch pipe?

Use the actual outside diameter from the manufacturer or measurement, then enter the actual wall thickness. The Wheatland A53 example lists 2.375 inches outside diameter for both trade size two schedules. The wall differs between the schedules.

Should I use density or the supplier’s mass per foot?

Use the published mass per foot if it covers the exact product scope. Check whether the listing includes threads, coatings or couplings before you add their masses separately. Material density estimates an ideal uniform annulus, so mill tolerances can cause differences.

Why does 25% depth fill less than 25% of the pipe volume?

A circular bore is narrow at the bottom. The lower quarter of the height contains 19.55% of the cross-sectional area, so a level pipe holds 19.55% of its full volume at that depth.

What do empty, loaded, and full each include?

All three include the dry pipe and entered accessories. Loaded adds liquid at each entered depth, while full replaces that with the liquid mass of the complete bore.

Similar Calculators