Motorcycle Gearing, RPM & Shift Planner
A sprocket ratio alone does not show how the gearbox, tyre rollout and engine torque curve interact. Compare up to four chain-drive alternatives with a shared primary ratio, up to eight gears and a supplied torque curve. The workspace plots road speed versus engine RPM for the selected gear across setups, and modeled wheel torque versus road speed across every gear in a selected setup. Inspect cruising RPM, upper/lower engine-window speeds, same-speed shift recovery and adjacent gear-band coverage. Switch metric/imperial inputs without changing physical quantities and export all model samples as exact fractions. These are kinematic and constant-efficiency calculations, not actual top-speed or acceleration predictions, shift recommendations, product compatibility checks or chain-length estimates. Examples are editable assumptions, not ratings for a particular motorcycle.
Compare the gears, not just the tooth count.
Explore sprockets, measured tyre rollout, cruising RPM and shift recovery with your gearbox and engine torque curve. Calculated road speeds are kinematic, not attainable top-speed predictions.
Current comparison calculated. Review speed, torque and shift details below.
Engine range and comparison
Enter input revolutions per output revolution for each ratio. Required numbers accept six decimal places or exact fractions; teeth require whole numbers. RPM limits are your authored calculation window, not verified engine limits.
Gearbox ratios
Order up to eight gears from low to high: ratios must strictly decrease. Use Move up/down to repair order; the planner never silently sorts the gearbox.
Engine torque curve
Enter two to sixteen knots in increasing RPM order. The first and last RPM must exactly match the engine window. Interpolation is straight-line between knots, with no extrapolation beyond them.
Sprocket and tyre alternatives
Compare up to four alternatives. Use measured loaded rolling circumference where possible, not tyre diameter. Constant transmission efficiency affects modeled wheel torque, not kinematic speed. Tooth counts and rollout do not establish product fitment.
Compare alternatives at equal engine RPM
| Setup | Final ratio | Final ratio change | Speed at equal RPM | RPM at equal speed | Wheel-torque factor at equal engine RPM |
|---|---|---|---|---|---|
| Base sprockets | 3 | 0 % | 0 % | 0 % | 0 % |
| Smaller front | ≈ 3.21429 | ≈ 7.14286 % | ≈ -6.66667 % | ≈ 7.14286 % | ≈ 7.14286 % |
| Smaller rear | ≈ 2.8 | ≈ -6.66667 % | ≈ 7.14286 % | ≈ -6.66667 % | ≈ -6.66667 % |
Changes are relative to Base sprockets. Torque-factor comparisons assume equal engine RPM and engine torque. At equal road speed, another setup may use a different part of the torque curve. Gearing does not increase engine power.
Road-speed scale: 0–≈ 171.429 km/h
- Base sprockets
- Smaller front
- Smaller rear
| Setup / gear | Overall ratio | Lower-range speed | Upper-range speed | Shift speed | Cruise RPM | Cruise state | Cruise engine torque | Cruise wheel torque |
|---|---|---|---|---|---|---|---|---|
| Base sprockets / First gear | 18 | ≈ 13.3333 km/h | ≈ 53.3333 km/h | 40 km/h | 13,500 RPM | above-range | Unavailable outside range | Unavailable outside range |
| Base sprockets / Second gear | 12 | 20 km/h | 80 km/h | 60 km/h | 9,000 RPM | above-range | Unavailable outside range | Unavailable outside range |
| Base sprockets / Third gear | 6 | 40 km/h | 160 km/h | 120 km/h | 4,500 RPM | within-range | ≈ 56.6667 N·m | 323 N·m |
| Smaller front / First gear | ≈ 19.2857 | ≈ 12.4444 km/h | ≈ 49.7778 km/h | ≈ 37.3333 km/h | ≈ 14,464.3 RPM | above-range | Unavailable outside range | Unavailable outside range |
| Smaller front / Second gear | ≈ 12.8571 | ≈ 18.6667 km/h | ≈ 74.6667 km/h | 56 km/h | ≈ 9,642.86 RPM | above-range | Unavailable outside range | Unavailable outside range |
| Smaller front / Third gear | ≈ 6.42857 | ≈ 37.3333 km/h | ≈ 149.333 km/h | 112 km/h | ≈ 4,821.43 RPM | within-range | ≈ 58.8095 N·m | ≈ 359.158 N·m |
| Smaller rear / First gear | ≈ 16.8 | ≈ 14.2857 km/h | ≈ 57.1429 km/h | ≈ 42.8571 km/h | 12,600 RPM | above-range | Unavailable outside range | Unavailable outside range |
| Smaller rear / Second gear | ≈ 11.2 | ≈ 21.4286 km/h | ≈ 85.7143 km/h | ≈ 64.2857 km/h | 8,400 RPM | above-range | Unavailable outside range | Unavailable outside range |
| Smaller rear / Third gear | ≈ 5.6 | ≈ 42.8571 km/h | ≈ 171.429 km/h | ≈ 128.571 km/h | 4,200 RPM | within-range | ≈ 54.6667 N·m | ≈ 290.827 N·m |
Wheel torque by road speed — Base sprockets
Each line is a gear over the supplied engine range. Dotted vertical connectors show torque before and after a shift at the same road speed; a shift below the torque curve has only its before marker. These are torque comparisons, not acceleration predictions.
Wheel-torque scale: 0–1,026 N·m
- First gear
- Second gear
- Third gear
| Shift | Road speed | Before RPM | After RPM | RPM drop | After state | Wheel torque before | Wheel torque after | Wheel-torque change |
|---|---|---|---|---|---|---|---|---|
| First gear → Second gear | 40 km/h | 6,000 RPM | 4,000 RPM | 2,000 RPM | within-range | 969 N·m | 608 N·m | ≈ -37.2549 % |
| Second gear → Third gear | 60 km/h | 6,000 RPM | 3,000 RPM | 3,000 RPM | within-range | 646 N·m | 266 N·m | ≈ -58.8235 % |
| Gear pair | Coverage | Start speed | End speed | Width |
|---|---|---|---|---|
| First gear / Second gear | overlap | 20 km/h | ≈ 53.3333 km/h | ≈ 33.3333 km/h |
| Second gear / Third gear | overlap | 40 km/h | 80 km/h | 40 km/h |
Overlap, touching and gap refer only to the authored RPM window. They do not determine the correct riding shift point. A zero before-shift wheel torque leaves percentage change undefined.
Complete samples — Base sprockets, Third gear
| Engine RPM | Wheel RPM | Road speed | Engine torque | Wheel torque |
|---|---|---|---|---|
| 2,000 RPM | ≈ 333.333 RPM | 40 km/h | 40 N·m | 228 N·m |
| 2,300 RPM | ≈ 383.333 RPM | 46 km/h | 42 N·m | ≈ 239.4 N·m |
| 2,600 RPM | ≈ 433.333 RPM | 52 km/h | 44 N·m | ≈ 250.8 N·m |
| 2,900 RPM | ≈ 483.333 RPM | 58 km/h | 46 N·m | ≈ 262.2 N·m |
| 3,200 RPM | ≈ 533.333 RPM | 64 km/h | 48 N·m | ≈ 273.6 N·m |
| 3,500 RPM | ≈ 583.333 RPM | 70 km/h | 50 N·m | 285 N·m |
| 3,800 RPM | ≈ 633.333 RPM | 76 km/h | 52 N·m | ≈ 296.4 N·m |
| 4,100 RPM | ≈ 683.333 RPM | 82 km/h | 54 N·m | ≈ 307.8 N·m |
| 4,400 RPM | ≈ 733.333 RPM | 88 km/h | 56 N·m | ≈ 319.2 N·m |
| 4,700 RPM | ≈ 783.333 RPM | 94 km/h | 58 N·m | ≈ 330.6 N·m |
| 5,000 RPM | ≈ 833.333 RPM | 100 km/h | 60 N·m | 342 N·m |
| 5,300 RPM | ≈ 883.333 RPM | 106 km/h | 59 N·m | ≈ 336.3 N·m |
| 5,600 RPM | ≈ 933.333 RPM | 112 km/h | 58 N·m | ≈ 330.6 N·m |
| 5,900 RPM | ≈ 983.333 RPM | 118 km/h | 57 N·m | ≈ 324.9 N·m |
| 6,000 RPM | 1,000 RPM | 120 km/h | ≈ 56.6667 N·m | 323 N·m |
| 6,200 RPM | ≈ 1,033.33 RPM | 124 km/h | 56 N·m | ≈ 319.2 N·m |
| 6,500 RPM | ≈ 1,083.33 RPM | 130 km/h | 55 N·m | ≈ 313.5 N·m |
| 6,800 RPM | ≈ 1,133.33 RPM | 136 km/h | 54 N·m | ≈ 307.8 N·m |
| 7,100 RPM | ≈ 1,183.33 RPM | 142 km/h | 53 N·m | ≈ 302.1 N·m |
| 7,400 RPM | ≈ 1,233.33 RPM | 148 km/h | 52 N·m | ≈ 296.4 N·m |
| 7,700 RPM | ≈ 1,283.33 RPM | 154 km/h | 51 N·m | ≈ 290.7 N·m |
| 8,000 RPM | ≈ 1,333.33 RPM | 160 km/h | 50 N·m | 285 N·m |
Samples include every torque knot, the shift RPM and 21 evenly spaced RPM points. Choose another setup or gear above for its full table; CSV contains all setups and gears. No tyre slip, aerodynamic drag, traction, drivetrain dynamics or product compatibility is modeled.
How to use this calculator
- Choose Sprocket comparison example or Larger rollout example, then select metric or imperial units. Enter the primary ratio, authored engine RPM window, shift RPM and cruising road speed.
- Enter gearbox ratios in low-to-high gear order, strictly decreasing. Use Move up/down to fix row order; no automatic sorting is applied.
- Supply a torque curve with two to sixteen increasing RPM knots. Match its first and last RPM exactly to the engine window. Use compatible measured or deliberately assumed engine torque data.
- Enter front/rear tooth counts, measured rolling circumference and constant torque-transmission efficiency for each setup. Choose the comparison reference; it cannot be removed until you explicitly select another.
- Select a setup and gear for detail. Compare equal-RPM speed lines, cruising state, wheel-torque curves, same-road-speed shift recovery and coverage bands. Keep upper-range speed distinct from attainable top speed.
- Inspect the complete sample table or export every setup/gear with Download CSV or Selectable CSV. Confirm mechanical compatibility and actual operating limits separately.
The Formula
The mathematical logic powering this calculation is:
Final-drive ratio F = rear sprocket teeth / front sprocket teeth. Overall ratio in a gear R = primary ratio × gearbox ratio × F, expressed as engine revolutions per wheel revolution. With measured rolling circumference C metres, wheel RPM = engine RPM / R and road speed in km/h = engine RPM × C ×60/(1000R). Upper-range speed is the speed implied at the authored upper RPM, not a prediction that the machine has enough power to reach it.
Interpolate the entered engine torque curve linearly between strictly ordered knots. The first and last knots must match the engine RPM window exactly. Modeled wheel torque = engine torque × overall ratio × transmission efficiency/100. Efficiency affects torque, not kinematic speed. No extrapolation is made outside the engine window. Gearing does not create engine power.
The common sample grid is the sorted distinct union of 21 evenly spaced engine RPM points, all torque knots and shift RPM. Plots, tables and CSV use those same exact samples. Cruising engine RPM = road speed / the gear’s speed-per-RPM coefficient. Classify below-range, within-range or above-range; boundaries are included. Outside the supplied torque curve, cruising torque is unavailable.
For an adjacent upshift at the authored shift RPM: after RPM = before RPM × next gearbox ratio/current gearbox ratio. Road speed is unchanged. RPM drop = before − after. Evaluate before/after wheel torque in the corresponding gears using the torque curve. Wheel-torque change percentage = (after/before −1)×100; it is unavailable if the after RPM is below the curve or before torque is zero. This percentage is distinct from RPM drop.
Each gear’s operating-speed band runs from its lower-window speed to its upper-window speed. Adjacent bands overlap if max(lower speeds) < min(upper speeds), touch if equal, or leave a gap otherwise. Return nonnegative interval widths. These bands describe the authored calculation window, not recommended riding shift points.
Reference comparisons: final-ratio change = (F/Fref −1)×100; equal-RPM speed change = ((C/F)/(Cref/Fref) −1)×100; equal-road-speed RPM change = ((F/C)/(Fref/Cref) −1)×100; equal-engine-RPM wheel-torque factor change = ((F×efficiency)/(Fref×efficiencyref) −1)×100. Equal-road-speed torque can differ because it uses another engine RPM, so do not confuse these comparisons.
Metric/imperial conversion uses exactly 0.0254 m/in, 1.609344 km/h per mph and 1.3558179483314004 N·m per lbf·ft. Cruise speed, all rollout values and all engine torque knots convert atomically. Incomplete or unrepresentable values retain the original draft. Ratios, tooth counts, RPM and efficiencies do not change.
Bounds: primary and gearbox ratios 0.1–10; lower/upper engine RPM 1–30,000 with lower strictly below upper; shift within that window; cruise 0–500 km/h; 1–8 strictly descending gearbox ratios; 2–16 increasing torque knots with torque 0–2000 N·m; 1–4 setups with front 5–60 and rear 10–150 whole teeth, rollout 0.1–5 m and efficiency greater than zero through 100%. Dimensional/ratio drafts accept six decimals and 12 significant digits or exact fractions with up to 32 digits per numerator/denominator. Tooth counts are integer strings. Invalid inputs suppress all results and exports.Worked Example
If you input:
- Engine and gearbox: Primary ratio 2; gearbox ratios 3, 2, 1; engine window 2000–8000 RPM; shift 6000 RPM; cruise 90 km/h.
- Torque curve: 40 N·m at 2000 RPM, 60 at 5000, 50 at 8000.
- Setups: Base 15/45 teeth; smaller-front alternative 14/45; smaller-rear alternative 15/42. Each uses 2 m rollout and 95% efficiency.
Result:
Base overall ratios are 18, 12 and 6. At 90 km/h, required engine speeds are 13,500, 9,000 and 4,500 RPM; only third gear is within the authored curve, with 170/3 N·m engine torque and 323 N·m modeled wheel torque. At a 6,000-RPM first-to-second shift, road speed stays 40 km/h, engine speed drops to 4,000 RPM and wheel torque changes from 969 to 608 N·m. The second-to-third shift occurs at 60 km/h, recovers to 3,000 RPM and changes wheel torque from 646 to 266 N·m. The 14/45 alternative increases final ratio by 50/7 ≈7.14286% and decreases equal-RPM road speed by 20/3 ≈6.66667%. Base third-gear upper-window speed is 160 km/h at 8,000 RPM; this is not a predicted attainable top speed.
Frequently Asked Questions
Does this predict actual top speed?
No. Upper-window speed is the road speed implied by the supplied RPM, reductions and rolling circumference. Available power, aerodynamic drag, rolling resistance, tyre slip, traction and control limits determine whether that speed can be reached. Those effects are not simulated.
Why does a smaller front sprocket increase cruising RPM?
With unchanged rear teeth and rollout, a smaller front sprocket increases rear/front reduction. More engine revolutions are required for the same wheel speed. At equal engine RPM the road speed is lower, while the constant-efficiency torque multiplication is larger.
Does more wheel torque mean more engine power?
No. A reduction trades rotational speed for torque, subject to losses. The planner scales wheel torque by ratio and efficiency but makes no claim that changing sprockets increases the engine’s power output. Actual acceleration also depends on mass, traction and resistance.
Why are some cruising or after-shift torque values unavailable?
The required RPM is outside the supplied torque curve. The planner still shows the kinematic RPM and road speed but does not invent torque by extending the curve. Shift-change percentage is also unavailable when its before-torque denominator is zero.
Should I enter tyre diameter or circumference?
Enter rolling circumference: distance traveled in one wheel revolution, preferably measured under relevant loading. The model does not infer it from a nominal tyre size or diameter. Rollout changes both speed-per-RPM and cruising RPM without changing the ratio-based wheel-torque multiplier.
What do overlapping or separated gear bands mean?
The bands show road speeds covered by your chosen lower/upper engine RPM window in each gear. Overlap means both gears can represent some shared speeds inside that window; touching means one common boundary; a gap means neither adjacent band covers that interval within the authored limits. These are not riding or shift recommendations.
Why is the equal-RPM torque comparison different from torque at a fixed road speed?
At equal engine RPM the same supplied engine torque applies to each setup, so the comparison is a reduction/efficiency factor. At fixed road speed, sprockets or rollout can move the engine to a different RPM and hence another torque-curve value. Use the cruising and complete sample tables for that distinction.
Does a valid tooth count mean the parts will fit?
No. Chain pitch, link count, sprocket clearance, alignment, wear, swingarm geometry and product fitment are not checked. Constant efficiency and a steady torque curve also omit shifting dynamics and drivetrain behavior. Use actual specifications and verified operating limits for mechanical decisions.
Similar Calculators
Fuel Cost Calculator
Calculate the fuel cost and consumption for any road trip or daily commute.
Motor RPM from Hz Calculator
Motor RPM from Hz for the exact fields in this tool, with clear inputs and an immediate result for planning or comparison.
Power Calculator
Calculate electrical power in watts from voltage and current, or find current from power and voltage.
Belt Length, Pulley & Center-Distance Fit Calculator
Compare belt lengths or timing-belt tooth counts against shaft adjustment limits. Inspect pulley diagrams, wrap angles, center distances, speed and complete CSV data.
Two-Stroke Oil Mix & Premix Planner
Calculate two-stroke petrol and oil additions, combine known premixes, check ingredient stocks and usable capacity, and explore feasible batch sizes.
