Belt Length, Pulley & Center-Distance Fit Calculator
A belt length alone does not show whether an available belt fits your mounting slots. Enter driver and driven pitch diameters—or timing pitch and tooth counts—along with the minimum, target and maximum shaft center distances. Compare up to twelve entered belt candidates, identify geometric fits and all closest ties, and inspect solved pulley tangents and wrap angles. An adjustment slider, length and wrap charts, paginated tables and full-precision CSV share one model. The calculator distinguishes pitch-circle contact, belts outside the adjustment window and inverse solutions beyond its supported domain. Ideal no-slip speed and authored-power torque are shown separately from geometric fit. This is an open two-pulley pitch-geometry study, not a product catalog, belt strength assessment, installation approval or recommendation for pretension, width, profile or permitted operating speed.
Find the belt that fits your adjustment range
Compare entered belt sizes, inspect pulley wrap and preserve the distinction between geometric fit and product suitability.
Define the drive
Compare two-pulley open-belt geometry using matching pitch/effective dimensions or timing-belt tooth counts. Enter your candidate sizes; no stock catalog or product recommendation is inferred.
Each mode retains separate diameter/teeth and candidate length/teeth drafts. Switching modes does not convert dimensions or reinterpret sizes.
1–50 mm; matching pitch alone does not establish profile compatibility.
Whole 6–1,000. No product minimum tooth count is inferred.
Whole 6–1,000; driver and driven may be unequal in either direction.
Must strictly separate pitch circles and not exceed the target.
Target must lie within the minimum and maximum, up to 100,000 mm.
May equal the minimum for fixed geometry; installation/tensioning space is not checked.
0–100,000 rpm. This is an entered speed, not a permitted product rating.
0–1,000 kW. Positive power needs nonzero speed; no power capacity is inferred.
Enter candidate belts
Illustrative sizes only. Use actual supplier pitch lengths or tooth counts. A geometric fit does not verify width, profile, stiffness, strength, guards, installation travel or tensioning.
Comparison updated: 3 candidates at or inside adjustment boundaries.
Target and geometric fits
Ideal pitch length at target center
551.2672 mm
Required length interval: 531.334–571.2068 mm.
Closest entered geometric fit
110 teeth
Closest means minimum absolute shift from target, with all ties within 0.00000001 mm retained. This is not a belt recommendation.
Approximate formula length: 551.2665 mm. Approximation minus exact-model length: -0.0007 mm. Numerical boundary labels do not account for manufacturing tolerances.
Inspect a solved geometry
Arrow keys select adjacent points from the canonical 101-row dataset. Solved candidates outside the adjustment range can be inspected but remain marked outside it.
Left: driver. Right: driven. Both rotate in the same direction. Diagram uses pitch circles, not pulley outside dimensions; the smaller circle may be visually tiny at extreme ratios.
- Center distance
- 200 mm
- Pitch length
- 551.2672 mm
- Driver wrap
- 170.8714°
- Driven wrap
- 189.1286°
- Each straight span
- 199.3657 mm
- Pitch-circle gap
- 152.2535 mm
- Driver / driven pitch diameters
- 31.831 / 63.662 mm
- Contact pitch equivalents
- 9.4929 / 21.0143
Contact pitch equivalents are continuous arc measures, not a count of fully loaded teeth or a strength check.
Horizontal: center 190–210 mm. Vertical: 531.334–571.2068 mm. 101 equally spaced center samples.
Blue line/point: required geometry. Purple triangles: candidates at or inside the adjustment boundaries. Overlapping markers can coincide; every candidate is listed in the comparison table.
Horizontal: center 190–210 mm. Vertical: 0–180 degrees. 101 equally spaced center samples.
Blue line/point: required geometry. Purple triangles: candidates at or inside the adjustment boundaries. Overlapping markers can coincide; every candidate is listed in the comparison table.
Candidate comparison
Travel is signed: lower travel = solved center − minimum, upper travel = maximum − solved center. Negative travel is outside the range. Boundary status uses the declared numerical tolerance; it is not a tolerance allowance for a manufactured belt.
| Candidate | Pitch length mm | Fit status | Solved center mm | Shift from target mm | Lower / upper travel mm | Driver / driven wrap ° | Contact pitch equivalents |
|---|---|---|---|---|---|---|---|
| 104 teeth | 520104 teeth | Below adjustment range | 184.3124 | -15.6876 | -5.6876 / 25.6876 | 170.0926 / 189.9074 | 9.4496 / 21.1008 |
| 108 teeth | 540108 teeth | Inside adjustment range | 194.348 | -5.652 | 4.348 / 15.652 | 170.6054 / 189.3946 | 9.4781 / 21.0438 |
| 110 teethClosest geometric fit | 550110 teeth | Inside adjustment range | 199.3644 | -0.6356 | 9.3644 / 10.6356 | 170.8423 / 189.1577 | 9.4912 / 21.0175 |
| 114 teeth | 570114 teeth | Inside adjustment range | 209.3949 | 9.3949 | 19.3949 / 0.6051 | 171.2818 / 188.7182 | 9.5157 / 20.9687 |
| 116 teeth | 580116 teeth | Above adjustment range | 214.409 | 14.409 | 24.409 / -4.409 | 171.4861 / 188.5139 | 9.527 / 20.946 |
Ideal no-slip kinematics
- Driven / driver speed ratio
- 0.5
- Driven speed
- 750 rpm
- Belt speed
- 2.5 m/s
- Driver torque
- 6.3662 N·m
- Ideal driven torque
- 12.7324 N·m
- Effective force difference
- 400 N
Torque and force follow the entered transmitted power; they are not capability ratings. Effective force is tight-minus-slack force, not pretension or bearing load. Zero speed with zero power leaves torque and force unavailable. Slip, creep, losses, startup loads and tensioning are excluded.
Adjustment-range data
Rows 1–25 of 101
| Center mm | Required length mm | Driver wrap ° | Driven wrap ° | Straight span mm | Pitch-circle gap mm | Approximation error mm |
|---|---|---|---|---|---|---|
| 190 | 531.334 | 170.3899 | 189.6101 | 189.3322 | 142.2535 | -0.0008 |
| 190.2 | 531.7326 | 170.4 | 189.6 | 189.5329 | 142.4535 | -0.0008 |
| 190.4 | 532.1311 | 170.4101 | 189.5899 | 189.7336 | 142.6535 | -0.0008 |
| 190.6 | 532.5298 | 170.4202 | 189.5798 | 189.9343 | 142.8535 | -0.0008 |
| 190.8 | 532.9284 | 170.4303 | 189.5697 | 190.135 | 143.0535 | -0.0008 |
| 191 | 533.327 | 170.4403 | 189.5597 | 190.3357 | 143.2535 | -0.0008 |
| 191.2 | 533.7256 | 170.4503 | 189.5497 | 190.5364 | 143.4535 | -0.0008 |
| 191.4 | 534.1242 | 170.4603 | 189.5397 | 190.7371 | 143.6535 | -0.0008 |
| 191.6 | 534.5228 | 170.4703 | 189.5297 | 190.9378 | 143.8535 | -0.0008 |
| 191.8 | 534.9214 | 170.4803 | 189.5197 | 191.1385 | 144.0535 | -0.0008 |
| 192 | 535.32 | 170.4902 | 189.5098 | 191.3392 | 144.2535 | -0.0008 |
| 192.2 | 535.7187 | 170.5001 | 189.4999 | 191.5399 | 144.4535 | -0.0008 |
| 192.4 | 536.1173 | 170.51 | 189.49 | 191.7406 | 144.6535 | -0.0008 |
| 192.6 | 536.5159 | 170.5199 | 189.4801 | 191.9413 | 144.8535 | -0.0007 |
| 192.8 | 536.9146 | 170.5298 | 189.4702 | 192.142 | 145.0535 | -0.0007 |
| 193 | 537.3132 | 170.5396 | 189.4604 | 192.3427 | 145.2535 | -0.0007 |
| 193.2 | 537.7118 | 170.5494 | 189.4506 | 192.5433 | 145.4535 | -0.0007 |
| 193.4 | 538.1105 | 170.5592 | 189.4408 | 192.744 | 145.6535 | -0.0007 |
| 193.6 | 538.5091 | 170.569 | 189.431 | 192.9447 | 145.8535 | -0.0007 |
| 193.8 | 538.9078 | 170.5788 | 189.4212 | 193.1454 | 146.0535 | -0.0007 |
| 194 | 539.3064 | 170.5885 | 189.4115 | 193.3461 | 146.2535 | -0.0007 |
| 194.2 | 539.7051 | 170.5982 | 189.4018 | 193.5467 | 146.4535 | -0.0007 |
| 194.4 | 540.1037 | 170.6079 | 189.3921 | 193.7474 | 146.6535 | -0.0007 |
| 194.6 | 540.5024 | 170.6176 | 189.3824 | 193.9481 | 146.8535 | -0.0007 |
| 194.8 | 540.901 | 170.6272 | 189.3728 | 194.1487 | 147.0535 | -0.0007 |
Inverse-solver details
| Candidate | Status | Length residual mm | Iterations |
|---|---|---|---|
| 104 teeth | Below adjustment range | -2.259e-10 | 48 |
| 108 teeth | Inside adjustment range | -4.271e-10 | 48 |
| 110 teeth | Inside adjustment range | -4.571e-10 | 48 |
| 114 teeth | Inside adjustment range | 4.943e-10 | 48 |
| 116 teeth | Above adjustment range | 1.370e-10 | 48 |
Export the complete fit study
Includes active and retained inactive drafts, geometry, no-slip quantities, every candidate status, solver residuals and the complete adjustment dataset. CSV cells are text-quoted to preserve values and prevent spreadsheet formulas.
How to use this calculator
- Choose Timing-belt comparison, Equal pulleys, fixed center, or Short center, large ratio. Select Input convention; each mode retains its own dimensional and candidate-size drafts.
- Enter matching pitch diameters or timing pitch and pulley tooth counts. Use supplier pitch/effective measurements rather than outside dimensions.
- Enter Minimum, Target and Maximum center distance. The minimum must separate the pitch circles. Equal endpoints describe fixed geometry, not installation or tensioning clearance.
- Add labeled candidate belt pitch lengths or tooth counts. Read each fit status and signed adjustment travel; contact-boundary or unsupported results are not solved separated fits.
- Select a solved candidate or move the adjustment-range slider to inspect geometry. Compare wrap, required length, exact-versus-approximate length and the complete candidate table.
- Review ideal speed and the consequences of your entered power separately from product capability. Open the paginated data and inverse details, then download the complete CSV or use its selectable fallback.
The Formula
The mathematical logic powering this calculation is:
Use consistent pitch/effective dimensions, not outside or inside belt lengths. In timing mode, pulley pitch diameter = tooth pitch × pulley teeth / π and belt pitch length = tooth pitch × belt teeth. The same pitch does not establish matching tooth profile, width or product capability. The model has two coplanar parallel shafts and an open belt, with no idlers or crossed path.
Let driver pitch radius be r1, driven radius r2, center distance C and signed radius difference Δ = r2 − r1. Set θ = asin(Δ/C) and straight-span length S = sqrt((C − |Δ|)(C + |Δ|)). Driver wrap = π − 2θ; driven wrap = π + 2θ. Exact-model pitch length L(C) = 2S + r1(π − 2θ) + r2(π + 2θ). Both pulleys rotate in the same direction. Driver/driven labels remain attached to their inputs even when the driver is larger. Pitch-circle gap is C − r1 − r2; actual outside clearance is not checked.
The usual approximate length is Lapprox = 2C + π(r1 + r2) + Δ²/C. Displayed approximation error is Lapprox − L, not an uncertainty estimate. Near equal radii or very long centers, an integrated asin series evaluates this small difference without subtracting nearly equal full lengths. For equal pulleys, L = 2C + 2πr and C = (L − 2πr)/2. Timing contact pitch equivalents = pulley teeth × wrap/(2π); these continuous arc measures are not an exact count of fully loaded teeth.
Because dL/dC = 2sqrt(1 − (Δ/C)²) is positive in the separated-circle domain, an attainable pitch length has a unique center. Candidate inversion uses bracketed bisection between pitch-circle contact C = r1 + r2 and 100,000 mm. Contact is excluded as a separated fit. The solver requires center bracket width ≤max(1e−9 mm, 2e−13×C) and absolute length residual ≤max(1e−8 mm, 2e−12×L), within 100 iterations. A failure is unresolved rather than a solved value.
Candidate lengths below the contact limit have no separated fit; values within the declared length tolerance of contact are explicitly contact-boundary cases. A required center above 100,000 mm is outside the supported inverse domain. Other candidates are below, inside or above the entered adjustment interval. Lengths within numerical tolerance of an interval endpoint receive lower-boundary, upper-boundary or fixed-boundary labels. These numerical tolerances are not manufacturing allowances or proof that an actual belt can be installed and tensioned.
Target shift = solved center − target. Lower travel = solved center − minimum; upper travel = maximum − solved center. Negative travel identifies a position outside the adjustment range. Among candidates at or inside the boundaries, retain every closest-fit tie within 1e−8 mm of the minimum absolute target shift. No fitting candidate means no closest fit. An existing mathematical solution may be inspected even when it lies outside the mounting window.
Ideal driven rpm = driver rpm × r1/r2. Belt speed in m/s = π × driver pitch diameter in mm × driver rpm / 60,000. Convert entered kW to watts. At positive rpm, driver torque = watts/(2π × rpm/60); ideal driven torque = driver torque × r2/r1; effective tangential force difference = watts/belt speed. Effective force is tight-minus-slack force, not pretension or bearing load. At zero speed and zero power, torque and force are unavailable; positive power at zero speed is invalid. At nonzero speed and zero power they are zero.
The sensitivity dataset contains 101 equally spaced center positions including minimum and maximum, or one point for a fixed center. Charts and tables use these canonical values; complete geometry, candidate classifications and inverse residuals are retained in CSV. Inactive mode drafts are kept separately and exported without being used in the active calculation.
Limits: 1–12 candidate belts, printable labels of 1–60 characters and unique IDs. Diameter mode accepts pitch diameters 1–5,000 mm and belt pitch lengths 0.1–300,000 mm. Timing mode accepts pitch 1–50 mm, whole pulley teeth 6–1,000 and whole belt teeth 1–100,000. Center distances are 0.01–100,000 mm with minimum ≤ target ≤ maximum and minimum strictly greater than the sum of pitch radii. Driver speed is 0–100,000 rpm and entered power 0–1,000 kW. Plain decimal strings have at most six places; signs, fractions and exponent inputs are not accepted. Counts are not rounded. Model limits are computational bounds, not product ratings.
Excluded: belt stretch, sag, slip, creep, losses, dynamic/startup loading, tensioning, installation allowance, fatigue, number of belts, tooth-profile compatibility, width, outside-diameter clearance, guards, alignment, bearing and shaft loads, product availability and permissible speed or power. Do not infer drive suitability from geometry alone.Worked Example
If you input:
- Timing geometry: Pitch 5 mm; driver 20 teeth; driven 40 teeth
- Center distances: Minimum 190 mm; target 200 mm; maximum 210 mm
- Entered candidates: 104, 108, 110, 114 and 116 teeth; illustrative sizes, not a stock catalog
- Operating assumptions: Driver 1,500 rpm; entered transmitted power 1 kW
Result:
The target-center pitch length is approximately 551.2672 mm. Candidates with 108, 110 and 114 teeth fit inside the entered adjustment range. Their solved centers are approximately 194.3480, 199.3644 and 209.3949 mm. The 110-tooth candidate has the smallest target shift, about −0.6356 mm. The 104-tooth candidate is below the range at about 184.3124 mm, while 116 teeth is above it at about 214.4090 mm. Ideal driven speed is 750 rpm and belt speed is 2.5 m/s. The entered 1 kW implies a 400 N effective force difference, not pretension or a permissible load. Geometric fit does not establish product suitability.
Frequently Asked Questions
Can I use a belt’s outside length or pulley outside diameter?
Not directly. This model uses matching pitch/effective diameters and belt lengths. Outside, inside, datum and pitch conventions can differ by product. Obtain compatible measurements from the supplier; the calculator does not infer a conversion from a belt designation.
Does the closest geometric fit identify the belt I should buy?
No. It identifies entered candidates at or inside your adjustment limits and retains all ties for the smallest absolute target-center shift. Width, tooth profile, product availability, strength, installation travel, elastic tensioning and actual operating limits require separate verification.
Why does the exact length differ from the common formula?
The common expression approximates the unequal-pulley contact arcs and tangent geometry. Differences can matter with large diameter ratios and short centers. This calculator uses exact circular pitch geometry and displays the signed approximation error; it does not substitute the approximation for candidate inversion.
What do the boundary and travel labels mean?
Lower/upper/fixed-boundary labels mean the candidate length is within the declared numerical tolerance of a window endpoint. Lower travel is solved center minus minimum; upper travel is maximum minus solved center. Negative travel is outside the window. Numerical tolerance is not manufacturing tolerance or an installation allowance.
Can this model crossed belts, idlers or serpentine drives?
No. It models an open belt on two coplanar pulleys, both rotating in the same direction. Extra pulleys, crossed routing, belt thickness, sag and other contact paths need different geometry. A pitch-circle gap also does not guarantee clearance between actual outside dimensions or guards.
Are contact pitch equivalents a safe number of engaged teeth?
No. They are continuous contact arc lengths expressed in tooth pitches. The value may be fractional and does not count fully loaded teeth or establish a product-specific minimum. Tooth profile, stiffness, preload, speed and loading are outside this geometric measure.
Does effective force tell me how tightly to tension the belt?
No. Under the ideal no-slip power model it is tight-side tension minus slack-side tension. It is not pretension, individual strand tension or bearing load. Entered transmitted power is an assumption, not a calculated power rating; zero speed with positive power is rejected.
What happens when no belt fits or the inverse is unsupported?
The target length and required length interval remain available. Too-short or contact-boundary candidates do not receive a fictitious separated center. Candidates needing more than 100,000 mm center distance are explicitly outside the solver domain. A solved candidate outside your adjustment window remains marked outside it and is not selected as a closest fit.
Similar Calculators
Motorcycle Gearing, RPM & Shift Planner
Compare motorcycle sprockets, tyre rollout and gearbox ratios. Plot RPM versus speed, wheel torque and shift recovery, inspect cruising RPM and export complete exact tables.
Motor RPM from Hz Calculator
Motor RPM from Hz for the exact fields in this tool, with clear inputs and an immediate result for planning or comparison.
Power Calculator
Calculate electrical power in watts from voltage and current, or find current from power and voltage.
