Kitchen Remodel Cost & Quantity Planner

Connect measured kitchen quantities to written supplier quotes. Build separate cabinet-run elevations, place countertop rectangles on a shared plan, mark sink and cooktop exclusions, and measure backsplash sections. The planner calculates frontage and countertop union area without counting overlaps twice, then compares up to three quotes using explicit price units and gross or net area billing. Included items must identify the priced scope that covers them; missing active prices remain visible instead of becoming free work. Inspect diagrams, billable quantities and the cost breakdown, then export exact geometry and rounded quote totals. The examples contain illustrative prices, not local market estimates. This is a quantity and budget comparison, not a room layout approval, countertop fabrication plan, contractor recommendation or prediction of resale value.

Kitchen quantity studio

Connect your kitchen measurements to the quote

See cabinet frontage, countertop geometry and billed scope together. Compare complete quotes without hiding unpriced work.

Measure once, compare the same scope

Start with illustrative measurements and prices, then enter your actual kitchen and written quotes. Cabinet runs are separate elevations; countertop rectangles describe measured area. This does not produce a room-clearance check, slab cutting plan or fabrication specification.

Compare the entered quotes

Planned project total
USD 6,809.6
Contract plus separately held reserve.
Known priced subtotal
USD 5,836
Before entered discount, tax and reserve.
Held reserve
USD 573.6
Based on the complete pretax total.
Budget headroom
USD 1,190.4
Budget minus planned total; negative means over budget.
QuoteArea basisKnown subtotalPlanned totalMissing scopeComparison
Illustrative suppliergrossUSD 5,836USD 6,809.6None in entered scopeLowest complete modeled total

Complete means every active item in this entered scope has a price or an explicit inclusion. It does not establish that all work needed for the project is listed, or compare contractor quality. Prices, discounts and tax are entered assumptions.

Countertop area without overlap double-counting

Gross union area
2.64 m²
Measured exclusions
0.24 m²
Net surface area
2.4 m²
Measured countertop union and exclusionsGreen regions show the union of entered countertop rectangles. White dashed exclusions are removed from net area. The selected exclusion has a black outline. Exact dimensions are available in the coordinate tables.
Plan bounds: 3 m × 2 m, measured from the bottom-left origin. Geometry is scaled; very thin regions may be smaller than a screen pixel. Cell boundaries are calculation subdivisions, not proposed seams.

Sink exclusion: left 0.8 m, bottom 0.1 m, size 0.6 m × 0.4 m, area 0.24 m². This geometric exclusion does not certify a manufacturable cutout.

Gross boundary length: 10 m. Separately entered finished edge: 3.6 m. The full boundary is not automatically charged as finished edge.

Countertop region and exclusion coordinates
RegionRolex (m)y (m)Width (m)Depth (m)
Main topInput region0030.6
ReturnInput region00.60.61.4
Sink exclusionsink exclusion0.80.10.60.4

Cabinet frontage and unused run space

Base frontage
2.4 m
Wall frontage
1.8 m
Tall frontage
0 m

5 cabinet modules; 1 appliance modules. Fillers total 0.3 m and unused run width totals 2.9 m. Neither is silently charged as cabinet frontage.

Floor run: module widths and unused spaceModules appear left to right in entered order. Black outline marks the selected module; pale dashed space is unused width. Read module types and exact positions in the table.

Floor run: 3.1 m occupied + 0.9 m unused = 4 m available. Module heights in this strip are illustrative; widths are proportional.

Selected baseA (base): start 0 m, width 0.6 m, end 0.6 m.

ModuleKindStart (m)Width (m)End (m)
baseAbase00.60.6
baseBbase0.60.81.4
ovenappliance1.40.62
baseCbase213
fillerfiller30.13.1

Trace the billable scope

Illustrative supplier bills countertop gross area. Prices use the explicit units below, independent of the measurement display unit. Included work has no separate charge; unpriced active work remains unavailable.

ScopeBillable quantityUnit priceStatus / included inLine cost
Base cabinet fronts2.4 mUSD 1,000pricedUSD 2,400
Wall cabinet fronts1.8 mUSD 500pricedUSD 900
Tall cabinet fronts0 mUSD 1,500Inactive (zero quantity)USD 0
Countertop surface2.64 m2USD 400pricedUSD 1,056
Measured finished edge3.6 mUSD 50pricedUSD 180
Sink exclusions1 eachUSD 150pricedUSD 150
Cooktop exclusions0 eachUSD 100Inactive (zero quantity)USD 0
Other exclusions0 eachUSD 50Inactive (zero quantity)USD 0
Backsplash sections1.5 m2USD 100pricedUSD 150
Appliance modules1 eachUSD 700pricedUSD 700
Demolition1 jobUSD 300pricedUSD 300

From priced scope to project budget

Each segment starts at the preceding total. The discount moves left; entered tax and held reserve move right. Values are in USD; zero amounts remain in the table.

1. Base cabinet frontsUSD 2,400
Base cabinet fronts: 2400 USD; running total 2400
2. Wall cabinet frontsUSD 900
Wall cabinet fronts: 900 USD; running total 3300
3. Countertop surfaceUSD 1,056
Countertop surface: 1056 USD; running total 4356
4. Measured finished edgeUSD 180
Measured finished edge: 180 USD; running total 4536
5. Sink exclusionsUSD 150
Sink exclusions: 150 USD; running total 4686
6. Backsplash sectionsUSD 150
Backsplash sections: 150 USD; running total 4836
7. Appliance modulesUSD 700
Appliance modules: 700 USD; running total 5536
8. DemolitionUSD 300
Demolition: 300 USD; running total 5836
9. Entered discountUSD -100
Entered discount: -100 USD; running total 5736
10. Entered taxUSD 500
Entered tax: 500 USD; running total 6236
11. Held reserveUSD 573.6
Held reserve: 2868/5 USD; running total 34048/5
StepChangeRunning total
Base cabinet frontsUSD 2,400USD 2,400
Wall cabinet frontsUSD 900USD 3,300
Countertop surfaceUSD 1,056USD 4,356
Measured finished edgeUSD 180USD 4,536
Sink exclusionsUSD 150USD 4,686
Backsplash sectionsUSD 150USD 4,836
Appliance modulesUSD 700USD 5,536
DemolitionUSD 300USD 5,836
Entered discountUSD -100USD 5,736
Entered taxUSD 500USD 6,236
Held reserveUSD 573.6USD 6,809.6

Keep the measurements and quote trail

Export all inputs, cabinet positions, countertop union cells and boundaries, exclusions, every quote line, missing scope and complete totals. Geometry uses canonical metres and square metres with exact fractions. Prices and rounded line totals retain their billing units and entered currency.

How to use this calculator

  1. Load Measured kitchen example or Gross, net and missing scope, then open Edit measurements and quotes. Enter a currency label, project budget, held contingency and measurement unit. Use your supplier’s actual dimensions and written scope.
  2. Build each cabinet run in order using base, wall, tall, appliance and filler modules. Enter countertop rectangles and measured exclusions on a shared bottom-left coordinate plane. Add measured backsplash sections and separately entered finished-edge length.
  3. Add other quoted work, such as demolition, as extra scope with an explicit quantity and unit label. A quantity of 1 job represents a lump sum. New extra rows appear as unpriced in every quote until you supply their pricing status.
  4. Choose each quote to edit. Match its gross/net countertop basis and billing units, then enter separate unit prices or name the active priced row that includes bundled work. Leave genuinely missing prices unpriced. Enter quoted tax and discount as amounts.
  5. Update kitchen comparison. Inspect the countertop plan, cabinet run, billable-scope ledger and cost accumulation. Compare complete totals and budget headroom separately from known subtotals of incomplete quotes. Download kitchen CSV or show its selectable copy to retain the full calculation trail.

The Formula

The mathematical logic powering this calculation is:

Cabinet runs are separate ordered elevations. Each module starts where the preceding one ends; occupied width = sum of module widths and unused width = entered run length − occupied width. Module widths cannot exceed the run. Base, wall and tall cabinet frontage are summed separately. Cabinet count includes those three module types; appliance count includes appliance modules. Fillers and unused space are reported separately and do not automatically become cabinet frontage. No corner connection, aisle clearance or cross-run collision is inferred.
Countertop gross area is the exact union of entered axis-aligned rectangles. The model divides their combined x/y boundaries into cells and counts each covered cell once. Shared internal edges do not contribute to the gross boundary length; boundaries around empty internal regions do. Each rectangular exclusion must be fully covered by the countertop union, and exclusions may touch but cannot overlap. Net area = gross union area − total exclusion area. A boundary-touching exclusion is allowed as area geometry, not certified as a manufacturable cutout. The separately entered finished-edge length cannot exceed the gross boundary length. No seam, slab nesting, safe cutout radius, support or overhang recommendation is inferred.
Backsplash quantity = sum of entered width × height × section count. Extra scope uses its explicit entered quantity and unit label. These quantities remain independent: countertop regions are not inferred from cabinet runs, and backsplash deductions are not inferred from countertop exclusions.
Each quote chooses gross or net countertop area for billing. Length rates use metres or feet, area rates use square metres or square feet, counts use each and extra scope uses its entered unit. Billable quantity = canonical quantity / billing-unit factor, with 1 ft = 0.3048 m and 1 ft² = 0.09290304 m² exactly. Every quote contains one price-status record for each standard and extra scope row. A priced line cost = billable quantity × unit price, rounded half up to cents.
Included scope has no separate charge only when it directly names another active priced row that covers it. Self-references, chains and inactive or unpriced parents are rejected for active included work. A zero-quantity row is inactive and does not create missing scope. An active unpriced row retains an unavailable line cost; that quote has a known subtotal but no complete total, reserve, budget headroom or lowest-cost rank.
For a complete quote, known subtotal = sum of rounded priced lines. Pretax amount = known subtotal − entered discount and cannot be negative. Contract amount = pretax amount + entered tax. Held reserve = pretax amount × contingency percentage, rounded half up to cents. Planned project total = contract amount + held reserve. Budget headroom = entered budget − planned total, with negative results retained. Lowest complete modeled totals include ties, but compare only the listed scope and entered prices, not quality or project suitability. Tax is an entered amount, not a calculated legal rule.
Physical measurements support m, cm, mm, ft and in. Unit changes preserve quantities exactly; 1 in = 0.0254 m. Quote price units stay explicit. Switching a price unit converts both billing quantity and its saved price; conversion is rejected if it cannot remain exact within the supported six price decimals. Changing price status preserves the prior price draft. Adding extra scope creates an unpriced row in every quote.
Geometry uses exact rational arithmetic. Money uses integer cents after each declared rounding step, including beyond JavaScript safe-integer limits. CSV includes canonical metre/square-metre geometry, exact fractions, all input rows, union cells and edges, cabinet positions, quote line units and complete/incomplete totals. Display rounding does not feed back into the calculations.
Supported bounds: 0–8 cabinet runs with up to 30 modules each, 0–12 countertop rectangles, 0–12 exclusions, 0–12 backsplash sections and 0–20 extra scope rows; compare 1–3 quotes. Run and individual geometric lengths are positive through 100 m; countertop coordinates and outer right/top bounds are 0–100 m. Backsplash counts are integers 1–100. At least one billable scope quantity must be positive. Physical quantities accept unsigned decimals up to nine places or bounded exact fractions. Extra quantities are 0–1,000,000; prices are 0–1 billion currency units with up to six decimals. Budget, entered tax and discount allow two decimals through 1 billion; contingency allows 0–100% with four decimals. These numerical limits are not construction guidance.
The model excludes automatic local prices, installation labor unless entered, waste, material suitability, structural/code checks, appliance clearances, countertop fabrication or nesting, schedules, financing, tax advice and resale returns. The sources provide measurement and planning context. Union geometry, quote inclusion rules and cost accounting above are the calculator’s declared method, not supplier-specific billing requirements.

Worked Example

If you input:

  • Cabinet runs: Floor: base widths 0.6, 0.8 and 1 m, one 0.6 m appliance and 0.1 m filler in a 4 m run. Upper: 1 and 0.8 m wall modules plus 0.2 m filler in a 4 m run.
  • Surfaces: Countertops: 3 × 0.6 m plus a 0.6 × 1.4 m return. Sink exclusion: 0.6 × 0.4 m. Backsplash: 3 × 0.5 m. Finished edge: 3.6 m.
  • Illustrative prices: USD 1,000/m base frontage, 500/m wall frontage, 400/m² gross countertop area, 50/m edge, 150/sink, 100/m² backsplash, 700/appliance and 300 demolition.
  • Budget adjustments: USD 100 discount, USD 500 entered tax, 10% held reserve and USD 8,000 budget.

Result:

Base frontage is 2.4 m and wall frontage is 1.8 m. Gross countertop area is 2.64 m²; the 0.24 m² exclusion leaves 2.4 m² net. Backsplash area is 1.5 m². Priced lines total USD 2,400 + 900 + 1,056 + 180 + 150 + 150 + 700 + 300 = USD 5,836. After the USD 100 discount, pretax is USD 5,736. The contract amount including entered tax is USD 6,236; the separately held reserve is USD 573.60. Planned total is USD 6,809.60, leaving USD 1,190.40 budget headroom. The same rates billed on net countertop area produce a USD 6,704 planned total. The comparison’s bundled-sink quote with an unpriced appliance has only a USD 4,986 known subtotal and no complete final total.

Frequently Asked Questions

Does this estimate local kitchen remodeling prices?

No. It derives quantities from your measurements and applies prices you enter. Example prices are illustrative. Include installation, delivery, services, demolition or other needed work explicitly; a complete modeled quote only covers the rows you listed.

Why are gross and net countertop areas different?

Gross area counts the union of measured countertop rectangles before exclusions. Net area deducts the measured sink, cooktop and other exclusions. Suppliers may use different billing conventions, so each quote explicitly chooses gross or net. The calculator does not claim that one convention applies universally.

What happens when countertop rectangles overlap?

Overlapping regions are counted once. The exact union method also excludes shared internal edges from boundary length. Turning on cell boundaries reveals calculation subdivisions; these are not seam locations or a slab-cutting plan.

How do included items avoid double-counting?

An included item names another active priced scope row that covers its work. Its separate cost is zero because it is bundled, not because it is missing. Active included rows cannot point to themselves, another included row, an inactive row or an unpriced row.

Why can an incomplete quote show a subtotal but no total?

Known priced work can be added accurately while other active work remains unpriced. Presenting a final total or calling that quote cheapest would imply the missing work is free. Complete totals, reserves and rankings remain unavailable until the active scope is priced or explicitly included.

Are cabinet frontages interchangeable with cabinet counts?

No. Frontage sums widths separately for base, wall and tall modules, while cabinet count counts those modules. Appliance modules have their own count. Filler and unused run widths stay separate. Match the chosen billing basis to the written quote; use extra scope for a pricing method not represented by the standard categories.

Does the plan confirm a safe or manufacturable layout?

No. Cabinet runs are independent elevations, not a connected room layout. Countertop rectangles and exclusions describe area only. The tool does not check appliance clearance, supports, edge profiles, cutout corner radii, seams, slab availability, structural requirements or code compliance.

Can I change units without changing costs?

Measurement unit changes preserve physical quantities and leave quote units unchanged. Billing-unit changes convert the quantity and price together when the new price is exactly representable within six decimals. If not, the switch is rejected so you can keep the original billing unit or obtain a quote in the desired unit. Currency labels do not convert money.

Similar Calculators