Foundation Squaring Calculator & Rectangle Layout Planner
Plan a rectangular foundation, form or pad before measuring the diagonals. Enter a target width and depth to find the planned diagonal and a 3–4–5 corner check that fits. For a measured footprint, enter four side lengths and two diagonals. One diagonal reconstructs the outline and the other checks it. A scaled overlay compares the estimated corners with the target rectangle using the fixed baseline and your entered tolerances.
Plan and check a rectangular foundation
Set the planned width and depth. Reconcile two measured diagonals and compare the four corners to your target.
Target rectangle
Use one unit for all dimensions and tolerances. Measure between the same points in a horizontal plane.
Along the A to B baseline.
Perpendicular to the baseline.
Measured sides and diagonals
Label the corners A, B, C and D in sequence. AC locates the corners. Measure BD separately to check the reconstruction.
Maximum allowed difference between measured and implied BD.
Maximum allowed distance from a corner to its target.
A is fixed. The baseline points from A toward B. Positive y is on the left when looking from A toward B.
Independent diagonal check
BD checks the outline reconstructed using four sides and diagonal AC.
- Measured BD
- 11.7047 units
- Implied BD
- 11.7047 units
- Measured minus implied
- -6.130e-8 units
- Allowed diagonal gap
- 0.001 units
Tape and corner ledger
Estimated measured area 51.500002 units². Measured BD minus AC: -1.2953 units.
| Corner | Measured x | Measured y | Shift x | Shift y | Move distance | Opening | Tolerance |
|---|---|---|---|---|---|---|---|
| A | 0 units | 0 units | 0 units | 0 units | 0 units | 75.963758° | Within |
| B | 12 units | 0 units | 0 units | 0 units | 0 units | 90° | Within |
| C | 12 units | 5 units | 0 units | 0 units | 0 units | 84.805573° | Within |
| D | 1 unit | 4 units | -1 unit | +1 unit | 1.414213 units | 109.230669° | Exceeds |
Show selectable CSV
How to use this calculator
- Choose Plan rectangle or Audit measured layout. Enter the intended width along A→B and intended depth perpendicular to the baseline.
- For planning, read the full diagonal and the two mark lengths for the 3–4–5 check at corner A. Use the same unit for all values.
- For an audit, label the four corners in sequence along the outline. Enter all four sides, diagonal AC and a separately measured diagonal BD in the same horizontal plane.
- Enter a tolerance for the independent BD comparison and a separate maximum allowed corner move. Review any tape discrepancy before using the reconstructed offsets.
- Compare the outlines and open the tape and corner ledger for signed changes along and across the baseline. Download the CSV to keep a copy.
The Formula
The mathematical logic powering this calculation is:
For a planned rectangle of width W and depth H, either diagonal is √(W² + H²). The corner check fits the largest scaled 3–4–5 triangle into the two sides that meet at A. The candidate scales are min(W/3, H/4) and min(W/4, H/3). Choose the greater scale and multiply each leg and the diagonal of the check by it.
For a measured footprint, corner A is the origin and A→B defines positive x. Positive y is to the left when looking from A toward B. Reconstruct triangles ABC and ADC using their shared AC diagonal and the four side distances. For a point with distances r and s to endpoints of base length L, its along-base coordinate is (L² + r² − s²)/(2L). Its perpendicular distance is twice the triangle area from Heron’s formula divided by L. B and D lie on opposite sides of AC in the model. Require their line to cross the interior of AC, so the outline is convex and the corners follow the entered order. Rotate the reconstructed outline into the baseline coordinate frame.
The BD tape check compares entered BD with reconstructed BD. If the absolute gap exceeds the entered diagonal tolerance, the layout audit shows the gap and withholds corner comparisons. Subtract each reconstructed corner from its target coordinates to obtain signed shifts. The straight-line difference is the magnitude of these two shifts and is compared with the entered corner tolerance. Tolerance comparisons include a numerical guard of 2×10⁻¹² times the relevant layout length scale. The guard absorbs arithmetic rounding and limits reporting of nearly unresolved geometries.
Use one linear unit in both plan and audit. Side lengths and plan spans support 0.01 to 10,000 and tolerances support 0 to 10,000, with up to six decimal places. This is a horizontal geometry check for a single convex footprint. It does not assess elevations, structural condition, design, survey accuracy or a specified construction tolerance.Worked Example
If you input:
- Target width × depth: 12 × 5 units
- AB, BC, CD and DA: 12, 5, 11.045361 and 4.123106
- AC and BD diagonals: 13 and 11.7047
- Diagonal gap and corner tolerances: 0.001 and 0.03
Result:
The planned diagonal is 13 units. The independent BD check agrees within 0.001 units. Corner D differs by about 1.414213 units, approximately −1 along the baseline and +1 across it.
Frequently Asked Questions
How do I measure the sides and diagonals for a layout check?
Label corners A, B, C and D in order around the footprint. Use the same point at every corner and measure horizontal distances in a common unit. Enter AB, BC, CD, DA, AC and BD with those labels. Use BD as an independent reading.
Is a rectangle square as long as both diagonals match?
Equal diagonals are necessary for a rectangle, but can also occur in an isosceles trapezoid. The side measurements, corner positions and target dimensions help distinguish those cases.
Why can the second diagonal disagree with the reconstructed outline?
A different corner reference, mislabeled measurement, slope, tape sag or an inconsistent set of measurements can cause a discrepancy. Compare entered BD with the implied BD before relying on the coordinates.
What do positive and negative corner shifts mean?
Positive x moves in the A→B direction, and positive y moves left of that direction. Negative values move in the opposite direction. Corner A is fixed as the origin throughout the worksheet.
Does the corner tolerance represent a building code requirement?
It is the entered distance limit for this geometric comparison. Select it from your actual measurement purpose or project documents. This calculator does not assess the foundation or certify survey, construction or code compliance.
Similar Calculators
Triangle Calculator
Solve right or oblique triangles from sides and angles. Compare both SSA solutions, inspect scaled geometry, and export sides, angles, area and heights.
Polygon Area Calculator
Calculate polygon area from ordered coordinates, subtract cutouts, and inspect perimeter, centroid and point location on a consistently scaled plan.
Foundation Repair Quote & Depth Planner
Compare foundation repair quotes across supplied pier depths. Audit included-depth allowances, per-pier billing increments, fixed scope and missing prices.
Decking Joist Layout & Board Angle Planner
Check measured deck joist spacing against two entered limits. Compare diagonal board travel, exact bay widths and an equal-split layout.
