Ellipse Area Calculator & Cut Planner

Compare two elliptical shapes and see how a straight cut changes the amount of material and edge length on each side. Enter the full horizontal and vertical spans, use the same measurement unit for both plans, and choose a vertical or horizontal cut. Enter a measured center offset or solve for the offset that retains a target percentage.

Geometry worksheet

Compare ellipse cuts and retained area

Measure the whole ellipse, set two cuts and compare how much material and edge each cut leaves.

Use the same unit in both plans. Enter the full width and height of each ellipse.

Plan A

Positive moves right. The piece to the right of the cut is retained.

Plan B

Positive moves up. The piece above the cut is retained.

Both plans retain the same area. Plan B has 5.187419 units of retained boundary more.
Plan A retained area
14.740436 units²
19.550111% of 75.398224 units²
Plan B retained area
14.740436 units²
19.550111% of 75.398224 units²

Shared-scale ellipse cuts

Both outlines use the same scale. Green shading is the retained piece. The blue dashed line is the straight cut.

Plan A12 × 8 units

3 units right of center

Plan A ellipse with vertical cutWidth 12, height 8. 3 units right of center. Retained side is right. Retained area 14.740436 square units.xy

19.550111% retained

Plan B12 × 8 units

2 units above of center

Plan B ellipse with horizontal cutWidth 12, height 8. 2 units above of center. Retained side is above. Retained area 14.740436 square units.xy

19.550111% retained

Straight and curved edges

The retained boundary adds the new straight cut to the original curve.

Plan A16.664804 units total

Curve 9.7366 unitsCut 6.928203 units

Plan B21.852223 units total

Curve 11.459918 unitsCut 10.392305 units

Area and edge ledger
Area and edge measurements by plan
MeasurementPlan APlan B
Signed center offset3 units2 units
Whole ellipse area75.398224 units²75.398224 units²
Retained area14.740436 units²14.740436 units²
Remainder area60.657787 units²60.657787 units²
Whole ellipse perimeter31.730879 units31.730879 units
Retained curved edge9.7366 units11.459918 units
Remainder curved edge21.994279 units20.270961 units
Straight cut edge6.928203 units10.392305 units
Retained boundary16.664804 units21.852223 units
Remainder boundary28.922482 units30.663266 units
Download ellipse comparison CSV
Show selectable CSV

How to use this calculator

  1. Measure the full horizontal width and vertical height. Enter them in the same unit for both plans.
  2. Choose a vertical or horizontal cut. Plan A and Plan B can use different shapes or directions.
  3. Enter a signed distance from the ellipse center or switch to a retained percentage. A vertical cut retains the right side. A horizontal cut retains the upper side.
  4. Compare the shaded portions and both retained boundaries. Review the curved edge and straight cut separately.
  5. Open the ledger for the remainder measurements and download the comparison CSV.

The Formula

The mathematical logic powering this calculation is:

For a cut measured along an axis with semispan a, let b be half the span along the other axis, d the signed center offset and θ = arccos(d/a). Retain the side whose coordinate along the selected axis is at least d. The whole ellipse area is πab. The retained share is (θ − sin θ cos θ)/π, and the straight cut has length 2b sin θ. The remainder area is complementary. Target mode solves the same area equation for d, between −a and +a.

The continuous ellipse arc comes from integrating the parametric speed √(a² sin² t + b² cos² t). The whole perimeter is four times the integral from 0 to π/2. The retained arc is twice the integral from 0 to θ. Each piece’s boundary adds the same straight cut to its own curved edge. The calculator uses a bounded numerical integration for the arcs and exports more digits than it displays. Inputs represent a true ellipse, with horizontal or vertical cuts and no allowance for cutting width, seams or finishing.

Enter the full spans, from 0.002 to 2,000 units with up to three decimals. An offset supports up to four decimals and must stay within half the selected span, including its tangent points. A target from 0 to 100 percent supports up to three decimals. Enter both plans in the same unit. The output expresses area in square units and edges in the entered linear unit.

Worked Example

If you input:

  • Full width × height: 12 × 8 units
  • Plan A cut: Vertical, 3 units to the right of center
  • Plan B cut: Horizontal, 2 units above center

Result:

Both cuts retain 14.740436 square units of a 75.398224-square-unit ellipse. Plan A leaves a 16.664804-unit boundary and Plan B leaves a 21.852223-unit boundary.

Frequently Asked Questions

Should I enter diameters or semiaxes?

Enter the full horizontal width and full vertical height. The calculator halves those dimensions internally. You can read the whole ellipse area in the area ledger.

Can two cuts retain the same area and have different edges?

Yes. The retained share depends on offset divided by the semispan along the selected axis. Cuts in two directions can share that ratio while their chord and curved-edge lengths differ.

How do I find the cut that leaves a specific area?

Divide your intended retained area by the whole ellipse area, multiply by 100, and enter that percentage in target mode. Read the signed center offset and its direction from the result.

What do negative and positive offsets mean?

For a vertical cut, positive moves the cut right. For a horizontal cut, positive moves it up. The calculator retains the right or upper side respectively, so positive offsets retain less than half.

What happens at a tangent or a 0% or 100% target?

The cut touches the outline at a single point. Its straight edge has zero length, and the retained piece has either none or all of the ellipse’s area and perimeter.

Similar Calculators