Drilling Speeds and Feeds Calculator

Connect drill diameter and cutting data to a complete axial-motion estimate. Compare requested and applied RPM, distinguish tip depth from full-diameter cylindrical depth, and follow continuous and full-retract peck cycles through every feed, rapid and dwell move. Inspect a point-depth diagram, compare batch time, and export the complete setup. Metric and imperial displays retain the original quantities. This is an ideal kinematic worksheet, not a material recommendation or executable machine program.

Drilling setup and time

Follow the drill, not just the RPM

Connect cutting data, point depth and peck motion to a complete drilling-time comparison.

Enter cutting data from your tool and process documentation. Examples are arithmetic illustrations, not material recommendations. This ideal constant-rate comparison omits acceleration, tool changes and controller-specific behavior; it is not an executable machine program.

Enter nonnegative decimals with up to nine decimal places, without commas or exponents. Converted displays may be rounded; source quantities are retained. Speed and depth modes keep separate drafts.

Continuous batch 190.4 seconds. Peck batch 240.8 seconds. 5 pecks per hole.

Continuous batch

190.4 s

17.24 s per hole

Full-retract peck batch

240.8 s

5 pecks · 22.28 s per hole

Additional peck time

50.4 s

For 10 holes including the same positioning intervals.

Drill and depth

An ideal conical point extends beyond full-diameter depth. 180° explicitly represents a flat point. A shallow tip-depth setting can leave zero full-diameter cylindrical depth.

Speed and feed

Feed is per revolution, not per tooth. The ceiling reduces RPM first and preserves feed per revolution. It does not establish machine or tool suitability.

Motion and batch assumptions

Both cycles start and end at the R plane. Pecking retracts fully after every increment and rapidly reapproaches above the prior depth. Dwell is applied once at final depth. Positioning is charged only between holes. At most 1,000 pecks per hole.

Requested intent → applied settings

Requested RPM
1,000
Applied RPM
1,000
Applied cutting speed
31.41593 m/min
Penetration rate
100 mm/min
Ideal point length
5 mm
Final tip depth
25 mm
Full-diameter depth
20 mm
Nominal removal rate
7.853982 cm³/min

The requested spindle speed is applied. Removal rate assumes full-diameter engagement and does not integrate entry/exit material removal.

Where the drill point ends

Final position: solid blue surface line; dashed R plane; purple tip line. The drill width is schematic, not to scale. Vertical positions share one scale.

Ideal drill point length 5 mm; tip depth 25 mm; cylindrical depth 20 mm

Surface: 0 mm. R plane: −2 mm. Tip: 25 mm. Point length is additional to cylindrical depth.

One hole · depth over time

Continuous: solid blue. Peck: dashed purple. Depth increases downward; dwell is a horizontal segment. The selected motion ends at the marker. All events are available in the table.

One-hole depth versus seconds: continuous 17.24 s, peck 22.28 s-211.525mm011.122.3 s

Motion 1: feed, peck 1. From -2 to 6 mm; 4.8 s, ending at 4.8 s.

Where the batch time goes

Batch time components in seconds
Component (s)ContinuousPeck
Feed162186
Rapid5.431.8
Dwell55
Between holes1818
Total190.4240.8
Complete motion ledger

Full-retract peck cycle, one hole. Change Inspect cycle above to view the other sequence. CSV includes both complete sequences.

Page 1 of 1
One-hole motion ledger, lengths in mm, time in seconds
MotionKindPeckFrom (mm)To (mm)Distance (mm)Duration (s)End (s)
feed1-2684.84.8
retract16-280.164.96
approach2-2570.145.1
feed251274.29.3
retract212-2140.289.58
approach3-211130.269.84
feed3111874.214.04
retract318-2200.414.44
approach4-217190.3814.82
feed4172474.219.02
retract424-2260.5219.54
approach5-223250.520.04
feed5232521.221.24
dwell5252500.521.74
retract525-2270.5422.28

Keep the complete setup

CSV uses canonical mm, m/min, RPM and seconds even in imperial display. It includes assumptions, all input values, derived settings and every motion in both cycles.

How to use this calculator

  1. Choose Display units, then enter Drill diameter and Included point angle. Select Depth meaning and enter either Full-diameter depth or Tip depth. Each mode keeps a separate draft.
  2. Choose Speed entry: Spindle RPM or Peripheral cutting speed. Enter Feed per revolution and optionally enable an RPM ceiling. Use cutting data appropriate to your own tool and process documentation.
  3. Enter R-plane clearance, New-depth peck increment and Reentry above prior depth. Reentry cannot exceed the peck increment. Set Rapid rate and Final dwell per hole.
  4. Enter Number of holes and Between-hole positioning time. Positioning is applied exactly once between adjacent holes, not before the first or after the last.
  5. Review the point-depth diagram and one-hole motion chart. Choose Inspect cycle and use Inspect motion or the complete motion ledger to trace individual moves. Compare batch feed, rapid, dwell and positioning time.
  6. Download drilling CSV or open Complete drilling CSV text. The export includes both full motion sequences in canonical mm, m/min, RPM and seconds. Confirm actual controller behavior separately.

The Formula

The mathematical logic powering this calculation is:

With drill diameter D in mm, spindle speed n in RPM and cutting speed Vc in m/min: n = 1000 Vc/(πD), Vc = πDn/1000. Penetration rate vf = feed per revolution × applied RPM. Apply an enabled RPM ceiling first, retaining feed per revolution. Do not multiply drill feed per revolution by flute count. Nominal full-engagement removal rate = πD²vf/4000 in cm³/min.
For an ideal conical point with included angle α, point length h = D/[2 tan(α/2)]. A 180° point has h=0. Tip depth L equals entered tip depth, or entered full-diameter depth plus h. Full-diameter cylindrical depth is max(0,L−h).
Positive depth points downward; surface is 0 and clearance plane is −A. Continuous motion feeds from −A to L, dwells once, then rapidly retracts to −A. Peck targets advance by q to a final clipped target L. Between pecks, retract to −A, rapidly approach to previous target minus reentry s, then feed to the next target. Final dwell occurs once, before the last retract.
For N=ceil(L/q), peck feed distance = L+A+(N−1)s; peck rapid distance = L+(2N−1)A+qN(N−1)−(N−1)s. Feed/rapid seconds = 60×distance/rate in compatible units. Batch seconds = holes×single-hole seconds + (holes−1)×positioning seconds. The event ledger computes each motion explicitly and reconciles with these totals.
Tip-depth and 90°/180° geometry use exact decimal arithmetic for peck-count decisions. Other conical depths use floating-point geometry; an unresolved near-boundary case returns an error rather than guessing a final peck. This numerical check is not a controller or certified geometric tolerance. Conversion constants are 1 in = 25.4 mm and 1 ft = 0.3048 m.

Worked Example

If you input:

  • Drill diameter / point angle: 10 mm / 90°
  • Full-diameter depth: 20 mm
  • Spindle speed / feed per revolution: 1,000 RPM / 0.1 mm/rev
  • Clearance / peck / reentry: 2 / 6 / 1 mm
  • Rapid rate / final dwell: 3,000 mm/min / 0.5 s
  • Batch: 10 holes, 2 s between holes

Result:

The point adds 5 mm, giving 25 mm tip depth and five pecks. Applied feed is 100 mm/min. Continuous motion feeds 27 mm and rapids 27 mm, taking 17.24 s per hole including dwell. Peck motion feeds 31 mm and rapids 159 mm, taking 22.28 s. With nine 2-second positioning intervals, batch times are 190.4 s and 240.8 s: pecking adds 50.4 s under these assumptions.

Frequently Asked Questions

Does this recommend a drilling speed for my material?

No. It relates the cutting data you enter to geometry and ideal motion time. It has no material, coating, rigidity, coolant or tool-life database. The editable examples demonstrate arithmetic rather than recommended machining conditions.

Is drill feed per revolution the same as milling feed per tooth?

No. This tool uses axial advance for one complete spindle revolution. Penetration rate equals that value times RPM. Do not multiply it by flute count. The separate milling calculator handles effective teeth and radial chip thinning.

Why does full-diameter depth require more tip travel?

A pointed drill reaches the bottom first at its tip. The full-diameter portion trails it by the ideal conical point length. Entering cylindrical depth adds that point length. Tip-depth mode uses the entered tip endpoint directly and can leave no cylindrical depth when only part of the point enters.

Does the peck sequence reproduce G83 on my machine?

Not necessarily. This worksheet explicitly assumes full retraction to the R plane, rapid reentry above the previous target and one final dwell. Controller settings can alter retract height, reentry, peck reduction, dwell and other behavior. No G-code is generated.

What happens when the RPM ceiling is active?

The model limits spindle RPM and preserves feed per revolution, so penetration rate falls with RPM. It reports requested and applied values separately. It does not test machine power, torque, stability, tool suitability or acceptable chip formation.

Why is this an estimate rather than actual cycle time?

Motion is modeled at constant feed and rapid rates. Acceleration, deceleration, tool changes, spindle ramps, positioning details and controller overhead are excluded unless captured by the entered between-hole time. Very short moves can take substantially longer than a constant-rate estimate.

How are exact or nearly exact peck boundaries handled?

Decimal tip-depth inputs and 90°/180° point geometry use rational arithmetic to select the number of pecks. A genuine positive final increment is retained even when tiny. Other point angles involve approximate trigonometry; if the derived depth is too close to a peck boundary, the worksheet asks for a measured tip depth or revised increment instead of presenting an uncertain schedule as resolved. More than 1,000 pecks is unsupported and is never silently truncated.

Why can unit conversion show a rounded value without changing the result?

The worksheet retains the original quantity behind a converted display. Editing that value establishes a new quantity. Invalid nonblank dimensional drafts block a unit change, while blanks remain blank. The CSV uses canonical units regardless of display selection, and retains full numeric output precision rather than the shorter visual formatting.

Similar Calculators