Milling Speeds and Feeds Calculator

Connect cutter diameter, effective teeth and radial engagement to the feed you intend. Compare requested and limited settings, inspect the contact and chip profile, and keep nominal removal rate and ideal feed-motion time together in one exportable setup.

Milling workspace

Connect speed, feed and chip thickness.

Edit inputs

Use cutting data from your tool supplier. This calculator compares a 90° straight-sided cutter setup; it does not recommend settings for a material.

Table feed 1,000 mm/min; spindle speed 6,000 RPM.

After entered limits

1,000 mm/min

Table feed at 6,000 rpm

Radial chip thinning

1. Tool & cutting inputs

Switching converts every dimensional draft, including retained values.

Cutting edges contributing per revolution, not the number touching at once.

2. Engagement

From zero to the effective cutter diameter.

For straight-sided cutters with a 90° entering edge. Constant radial and axial engagement; no ball-nose or corner correction.

3. Entered ceilings & travel

Zero is allowed and stops feed motion.

Straight travel at the displayed feed. Not a total cycle-time estimate.

Angle & spindle inspectors

0–180°. Outside contact has no engaged chip thickness.

Retained inactive drafts

These values return when you select their input mode or enable their option. They do not affect the current calculation. All dimensional drafts must be valid or blank to change units.

Requires positive radial width. Feed per tooth is adjusted for radial chip thinning.

0–100% of the effective cutter diameter.

Explore the setup

Spindle speed & table feed

How your chosen feed input behaves across requested spindle speeds. Markers show the current operating values.

Requested · circleWith limits · square

Table feed: 0 to 1,273.24 mm/min

Requested and limited feed over spindle speedSolid blue requested curve, dashed green limited curve. The full numerical series is available in the chart tables and report. Zero spindle speed is an axis guide only.
0 RPM6,366.198 rpm

Requested spindle speed

Each positive RPM sample preserves the selected feed intent before applying valid machine limits.

The zero-RPM endpoint is an axis guide, not an operating point.

At 45 deg: inside contact

Requested chip
0.03535534 mm
With limits
0.02946278 mm
Requested & limited values
Operating values. Units appear with every quantity. Rounding is for display; the complete report retains higher precision.
QuantityRequestedAfter spindle ceilingAfter entered ceilings
Spindle speed6,366.198 rpm6,000 rpm6,000 rpm
Cutting speed200 m/min188.4956 m/min188.4956 m/min
Table feed1,273.24 mm/min1,200 mm/min1,000 mm/min
Feed per tooth0.05 mm/tooth0.05 mm/tooth0.04166667 mm/tooth
Maximum chip thickness0.04 mm0.04 mm0.03333333 mm
Feed per revolution0.2 mm0.2 mm0.1666667 mm
Material removal rate12.7324 cm³/min12 cm³/min10 cm³/min
Ceilings are applied in order: spindle first, then table feed. Equality does not apply a reduction.
CeilingIncoming valueEntered maximumComparison
1. Spindle speed6,366.198 rpm6,000 rpmabove ceiling · reduced
2. Table feed1,200 mm/min1,000 mm/minabove ceiling · reduced

The RPM limit preserves tooth feed. The feed limit is applied second and can reduce the achieved chip thickness.

Ideal feed-motion time. Excludes acceleration, rapids, entries, retracts, dwell and tool changes.
RunTravel lengthTime at feedSwept material volume
Requested600 mm0.4712389 min6 cm³
With limits600 mm0.6 min6 cm³
Engagement factors & exact regime

Radial chip thinning. Feed per tooth and maximum chip thickness differ below half-diameter engagement. Zero feed makes the entire thickness curve zero.

Engagement ledger. Tiny nonzero deficits remain visible even when a rounded chip factor reads 1. These are mathematical quantities, not machining tolerances.
QuantityValue
Effective diameter10 mm
Radial width2 mm
Axial depth5 mm
Radial width / diameter0.2
Chip factor k0.8
Chip-factor deficit 1 − k0.2
Compensation factor 1 / k1.25
Compensation excess 1 / k − 10.25
Contact angle53.1301 deg
Remaining angle to 180°126.8699 deg
Geometric peak angle53.1301 deg
Full chart series & precision

Save, inspect & reuse

Input files preserve every draft and unit-conversion anchor. The report adds results, chart series and assumptions.

Selectable report CSV
Save or import a complete input problem

Choose CSV or TSV, paste a complete file, then apply it. A malformed file leaves the current setup untouched. Valid files may contain unfinished numeric drafts; those load with the relevant field errors.

Use the downloaded nine-column input format. A complete report is a separate format and cannot be imported as input.

Model scope & numerical conventions

One straight-sided 90° cutter, constant radial width and axial depth. No material recommendation, ball-nose correction, cutting-force model or machine suitability assessment.

Computational input limits are not acceptable machining ranges. Decimal inputs and unit changes are exact; π, square roots and trigonometric quantities use bounded numerical approximations. Display rounding does not change ceiling or engagement decisions.

  • One straight-sided cutter with a 90° cutting edge; use its effective cutting diameter. Ball-nose, round-insert and other entering-angle corrections are outside this model.
  • Effective cutting edges means the edges contributing per revolution, not the instantaneous number in contact.
  • Cutting data and machine ceilings are supplied by you. No material, tool-life, power, rigidity, or safe-feed recommendation is inferred.
  • Machine limits are comparisons: RPM first, then table feed. Fractional RPM is retained throughout the arithmetic.
  • Path time is ideal feed-motion time, excluding acceleration, rapids, approach, retract, pauses and tool changes. Zero engagement can still have feed-motion time.
  • Computed precision does not imply manufacturing precision. Exact rational metadata represents the entered mathematical quantities and unit conversions.

Methods: Sandvik milling formulas; ISCAR milling guide; NIST unit conversions.

How to use this calculator

  1. Choose Measurement system, then enter Effective cutting diameter and Effective teeth per revolution for a straight-sided 90° cutter. Choose Engagement input: Radial width or Percent of diameter. Enter Radial width or Diameter engagement, then Axial depth.
  2. Choose Speed input: Cutting speed or Spindle speed. Choose Feed input: Feed per tooth, Table feed or Target maximum chip thickness. Each inactive entry remains available when you return to its mode; a mode change does not silently reinterpret one quantity as another.
  3. Read requested spindle speed, table feed and maximum chip thickness. Inspect the contact arc and chip profile to see the radial-engagement relationship. Target maximum-chip mode needs positive engagement; zero feed and zero axial depth have explicit meanings.
  4. Optionally enable Compare a spindle ceiling and enter Maximum spindle speed, or Compare a feed ceiling and enter Maximum table feed. Compare the requested setup, the result after the spindle ceiling and the achieved result after the feed ceiling. The selected feed intent determines what is preserved through the first step.
  5. Optionally enable Estimate time at feed and enter Travel length. Use Inspect an engagement angle with Angle from entry, or Inspect another spindle speed with Probe spindle speed. Distinguish ideal feed-motion time from complete cycle time, and an outside-contact probe from zero-thickness contact.
  6. Choose Import format and paste Complete problem text to restore a full CSV/TSV setup. Review the quantity ledger, then request the CSV download or select the same CSV text. Correct or disable invalid optional fields before complete result export; preserve the assumptions with the values.

The Formula

The mathematical logic powering this calculation is:

For a straight-sided 90° cutter, cutting speed Vc = π D n / 1000 when D is in mm, n is RPM and Vc is m/min. Thus n = 1000 Vc / (π D). In inches and ft/min, Vc = π D n / 12. Table feed vf = fz × n × z, where fz is feed per effective tooth and z is the effective cutting-tooth count; feed per revolution is fz × z. Enter cutting data from your own source: the illustrative examples are not recommendations for a material or tool.
For radial engagement fraction u = ae / D, the maximum-chip factor is k = 2√(u(1−u)) below half-diameter engagement and k = 1 at or above half. Then hmax = k fz; target maximum-chip mode derives fz = hmax / k and requires positive radial engagement even when the target chip is zero. Zero engagement has no contact. The ideal contact profile is h(θ) = fz sin(θ) over the modeled engaged arc, with its maximum at 90° when that angle lies inside the arc. This is maximum chip thickness, not an average-chip formula.
The requested setup remains visible independently of optional ceilings. Apply the RPM ceiling first. Tooth-feed and maximum-chip modes preserve their tooth-feed intent and recompute table feed; direct table-feed mode preserves its entered table feed and recomputes tooth feed. Apply the table-feed ceiling second, then recalculate achieved tooth feed, maximum chip and nominal removal rate. Meeting these two ceilings does not establish tool or machine suitability, stability, power availability or achievable surface finish.
Nominal removal rate is ap × ae × vf / 1000 in cm³/min for mm inputs, or ap × ae × vf in in³/min for inch inputs. It is zero at zero engagement, zero axial depth or zero feed. Ideal feed-motion time is path length divided by table feed in compatible units. Zero path has zero modeled time even at zero feed; a positive path at zero feed has no finite feed-motion time. Acceleration, approaches, rapid moves, tool changes and other cycle events are not included.
Speed modes, feed modes and engagement modes retain their separate drafts. Metric/imperial switches convert compatible nonblank dimensional drafts, including inactive and disabled fields, atomically; malformed nonblank text blocks the switch and blanks remain blank. Verified source/display anchors preserve a quantity when the converted display cannot terminate exactly. Editing a field clears its anchor. The international inch is exactly 25.4 mm and foot exactly 0.3048 m. Arithmetic precision is not manufacturing or measurement accuracy.
One invalid enabled ceiling leaves requested results available but makes the whole limited comparison unavailable. Invalid enabled path or inspection fields likewise retain the valid setup while blocking complete result export until corrected or disabled. Disabled drafts remain preserved. A chart RPM-zero endpoint is only an axis guide, not an operating point; very small positive quantities remain in the full ledger even when the diagram cannot resolve them.
Authored scalars are decimal/scientific tokens of at most 160 characters and 16 significant digits, ignoring insignificant zeros, with explicit exponent magnitude at most 30. Teeth are decimal integers 1–200. Canonical diameter is 0.001–1000 mm; entered RPM is 1e−6–1e7; cutting speed is 1e−9–1e7 m/min. Other positive entered lengths/feed values are at least 1e−12 in their canonical metric unit, with maxima 1000 mm axial depth, 100 mm tooth/max-chip feed, 1e9 mm/min table feed and 1e9 mm travel. Radial width is zero through diameter. Percent and angle entries allow 12 effective decimal places in 0–100% and 0–180°. Derived values can exceed authored bounds. Blank active inputs, expressions, fractions, grouping commas and nonfinite values are rejected. Bounded work can return an explicit numerical limit instead of an unproved comparison.
The complete-input CSV/TSV imports all retained values, mode choices, options and verified anchors using the documented nine-column schema. It preserves structurally valid unfinished numeric drafts so they can be corrected in the workspace. Unknown, missing or duplicate records, malformed anchors and incompatible structural units reject the whole import. The complete result CSV uses the same model values as the charts and tables.
The straight-sided 90° assumption excludes ball-nose, round-insert, lead-angle and other effective-diameter corrections. No material/tool database, power or torque prediction, controller instructions, chatter model or feed recommendation is supplied. The formulas and engagement concepts follow Sandvik Coromant's current Milling formulas and definitions and ISCAR's Milling Applications and Cutter Basics guide; those references do not certify a particular setup.

Worked Example

If you input:

  • Measurement system: Metric
  • Effective cutting diameter (mm): 10
  • Effective teeth per revolution: 4
  • Speed input: Cutting speed
  • Cutting speed (m/min): 200
  • Feed input: Feed per tooth
  • Feed per tooth (mm/tooth): 0.05
  • Engagement input: Radial width
  • Radial width (mm): 2
  • Axial depth (mm): 5
  • Compare a spindle ceiling: Enabled
  • Maximum spindle speed (RPM): 6000
  • Compare a feed ceiling: Enabled
  • Maximum table feed (mm/min): 1000
  • Estimate time at feed: Enabled
  • Travel length (mm): 600
  • Inspect an engagement angle: Enabled
  • Angle from entry (degrees): 45

Result:

Illustrative 10 mm cutter, four effective teeth, cutting speed 200 m/min, tooth feed 0.05 mm, radial width 2 mm and axial depth 5 mm. Requested spindle speed is 20000/π ≈ 6366.20 RPM and table feed 4000/π ≈ 1273.24 mm/min; maximum chip is 0.04 mm. The 6000 RPM ceiling first gives 1200 mm/min while retaining tooth feed. The 1000 mm/min feed ceiling then gives achieved tooth feed 1/24 mm, maximum chip 1/30 mm and nominal removal rate 10 cm³/min. The 600 mm travel takes 0.6 min at that constant achieved feed. These are arithmetic inputs, not recommended cutting data.

Frequently Asked Questions

Does this recommend a cutting speed or feed for my material?

No. Enter manufacturer or other chosen cutting data and treat the examples as arithmetic demonstrations. The workspace relates those values and compares explicit RPM/feed ceilings; it does not select a tool, account for rigidity or chatter, predict spindle power or guarantee a suitable cut. Its cutter model is straight-sided with a 90° entering angle, without ball-nose, round-insert or other geometry corrections.

How do feed per tooth, table feed and maximum chip thickness differ?

Feed per tooth is advance per effective cutting tooth. Table feed is that value multiplied by RPM and the effective cutting-tooth count. Maximum chip thickness additionally depends on radial engagement. Choose the quantity you intend to control; the other quantities are derived. Separate mode entries are retained rather than overwritten by a rounded derived result.

When does radial chip thinning apply?

In this restricted model, engagement below half the diameter gives a maximum chip thinner than feed per tooth. The factor is 2√(u(1−u)), where u is radial width divided by diameter. At or above half diameter the contact arc includes the maximum and hmax equals feed per tooth. Zero width means no contact, so a target-chip input cannot uniquely determine feed even when its target is zero. The profile is not an average-chip calculation.

What happens when a machine ceiling is lower than my request?

The comparison applies the RPM ceiling first. Tooth-feed and target-chip modes preserve their tooth-feed intent, while direct table-feed mode preserves table feed. A feed ceiling is applied afterward and the achieved chip quantities are recalculated. Requested values stay visible. One invalid enabled ceiling makes the comparison unavailable without erasing a valid requested setup; correct it or disable it before complete export.

Do unit switches preserve my setup and inactive entries?

Yes. Compatible length, speed and feed quantities are converted using exact international-inch/foot relationships. Nonblank inactive and disabled dimensional entries are also checked and converted; malformed entries block the switch as a whole, and blanks remain blank. A verified conversion anchor retains the underlying quantity when its display must round. An authored edit clears that field's anchor.

Is the path result a complete machining-cycle time?

No. It is path length divided by constant table feed. It omits acceleration, deceleration, rapid travel, approach and retract moves, tool changes and other events. A zero path gives zero modeled time; a positive path with zero feed has no finite feed-motion time. Nominal material-removal rate assumes the entered width and axial depth stay constant, and does not predict power demand.

What can the charts and complete export tell me?

The RPM/feed comparison and contact/chip profile use the same calculated quantities as the ledger. Inspect a point to distinguish requested intent, applied ceilings and achieved values. Full exact arithmetic metadata and bounded-irrational values remain available even when tiny differences cannot be drawn distinctly. Complete input CSV/TSV preserves modes and retained drafts; complete result export requires every enabled optional field to be valid. These calculations do not establish physical measurement accuracy.

Similar Calculators