Conduit Fill Calculator
See how planned cables change conduit occupancy. Compare listed inside diameters, inspect each cable group's contribution, and check an explicit area target.
Compare the bundle now and later.
EMT 1/2 in · area fill
- Now · 3 cables
- ≈ 30.0478 %
- Planned · 5 cables
- ≈ 50.0797 %
Smallest listed for the planned area target: EMT 3/4 in.
Area comparison only. Installation suitability and code requirements need separate checks.
Jump to comparisonsExamples and reset
Units and area target
mm: millimetres · in: inches. Unit changes preserve physical dimensions.
About the target and dimensions
The PPI 2021 reference profile uses 53% for one cable, 31% for two, and 40% for three or more. Check applicability separately. This is not an adopted-code, pulling, thermal or physical-packing check.
Dimensions include the round cable's jacket or insulation. Unit changes preserve all valid physical dimensions; blank drafts stay blank and malformed dimensions prevent conversion.
Cable groups
Use round outside diameters including insulation or jacket. “Add later” means extra cables.
Up to 24 groups. Counts are whole numbers from 0 to 1,000,000 per field.
Conduits to compare
Ten nominal inside diameters, trade sizes 1/2–4 in, from Wheatland sheet WEL-101625. A trade size is not an actual inside diameter. Custom candidates can represent measured or other manufacturer dimensions.
Inspect how many further copies could meet the area target after all planned additions. A zero-count group can define a future cable size.
Updated: 3 cables now, 5 planned. EMT 3/4 in.
Current and planned comparisons
Smallest listed size for the planned bundle
EMT 3/4 in
Based on nominal diameter and the selected area target. Equal smallest sizes are listed together.
Bundle count
3 now → 5 planned
Current area ≈ 58.9049 mm²
Planned area ≈ 98.1748 mm²
Area-derived minimum ID · planned
≈ 17.6777 mm
Continuous area calculation only. Listed size decisions use unrounded comparisons, not this rounded diameter.
Inside diameter ≈ 15.7988 mm · inside area ≈ 196.037 mm²
Current fill
≈ 30.0478 %
Below area target
Target 40 %
Target minus fill: ≈ 9.95217 percentage points.
Planned fill
≈ 50.0797 %
Above area target
Target 40 %
Target minus fill: ≈ -10.0797 percentage points.
Additional capacity after the planned bundle
For more copies of Network cable, these additional counts meet the selected area target:
No additional count meets the target
Largest feasible addition
None
Adding the next one
Above area target
Every count from zero through
Planned base already exceeds target
Inspect capacity boundary counts
| Extra copies | Total count | Fill | Target | Outcome |
|---|---|---|---|---|
| 0 | 5 | ≈ 50.0797 % | 40 % | Above area target |
| 1 | 6 | ≈ 60.0957 % | 40 % | Above area target |
| 2 | 7 | ≈ 70.1116 % | 40 % | Above area target |
| 3 | 8 | ≈ 80.1275 % | 40 % | Above area target |
Compare the inside space
Each pair uses the same fill scale. Solid bars show current fill; hatched bars include later additions. Dashed markers show each snapshot’s area target.
Current ≈ 30.0478 % · target 40 %
Planned ≈ 50.0797 % · target 40 %
Planned: Above area target.
Current ≈ 17.1214 % · target 40 %
Planned ≈ 28.5357 % · target 40 %
Planned: Below area target.
Current ≈ 10.5644 % · target 40 %
Planned ≈ 17.6073 % · target 40 %
Planned: Below area target.
Current ≈ 6.1043 % · target 40 %
Planned ≈ 10.1738 % · target 40 %
Planned: Below area target.
Current ≈ 4.48479 % · target 40 %
Planned ≈ 7.47465 % · target 40 %
Planned: Below area target.
Current ≈ 2.7209 % · target 40 %
Planned ≈ 4.53484 % · target 40 %
Planned: Below area target.
Current ≈ 1.55866 % · target 40 %
Planned ≈ 2.59776 % · target 40 %
Planned: Below area target.
Current ≈ 1.03217 % · target 40 %
Planned ≈ 1.72028 % · target 40 %
Planned: Below area target.
Current ≈ 0.790842 % · target 40 %
Planned ≈ 1.31807 % · target 40 %
Planned: Below area target.
Current ≈ 0.618894 % · target 40 %
Planned ≈ 1.03149 % · target 40 %
Planned: Below area target.
This is area accounting, not a drawing of how cables pack or pass through bends. Values are rounded for display; target classifications use unrounded entered dimensions.
Where the area goes
Each nonempty bar represents 100% of its own bundle’s occupied area. Groups run left to right in the numbered table order; zero shares occupy no segment.
Current≈ 58.9049 mm²
Planned≈ 98.1748 mm²
| Group | Current area | Current share | Planned area | Planned share |
|---|---|---|---|---|
| 1. Network cable | ≈ 58.9049 mm² | 100 % | ≈ 98.1748 mm² | 100 % |
Shares describe occupied cable area, not the conduit’s fill percentage. Physical areas use π and are approximate.
Complete conduit comparison table
| Candidate | Inside diameter | Current fill / target | Planned fill / target | Planned outcome | View |
|---|---|---|---|---|---|
| EMT 1/2 in | ≈ 15.7988 mm | ≈ 30.0478 % / 40 % | ≈ 50.0797 % / 40 % | Above area target | |
| EMT 3/4 in | ≈ 20.9296 mm | ≈ 17.1214 % / 40 % | ≈ 28.5357 % / 40 % | Below area target | |
| EMT 1 in | ≈ 26.6446 mm | ≈ 10.5644 % / 40 % | ≈ 17.6073 % / 40 % | Below area target | |
| EMT 1 1/4 in | ≈ 35.052 mm | ≈ 6.1043 % / 40 % | ≈ 10.1738 % / 40 % | Below area target | |
| EMT 1 1/2 in | ≈ 40.894 mm | ≈ 4.48479 % / 40 % | ≈ 7.47465 % / 40 % | Below area target | |
| EMT 2 in | ≈ 52.5018 mm | ≈ 2.7209 % / 40 % | ≈ 4.53484 % / 40 % | Below area target | |
| EMT 2 1/2 in | ≈ 69.3674 mm | ≈ 1.55866 % / 40 % | ≈ 2.59776 % / 40 % | Below area target | |
| EMT 3 in | ≈ 85.2424 mm | ≈ 1.03217 % / 40 % | ≈ 1.72028 % / 40 % | Below area target | |
| EMT 3 1/2 in | ≈ 97.3836 mm | ≈ 0.790842 % / 40 % | ≈ 1.31807 % / 40 % | Below area target | |
| EMT 4 in | ≈ 110.084 mm | ≈ 0.618894 % / 40 % | ≈ 1.03149 % / 40 % | Below area target |
Save the plan and report
The report includes assumptions, both snapshots, every candidate and capacity boundary. Complete input files preserve editable drafts for reuse. Text cells are encoded to prevent spreadsheet formulas; import here restores them.
Complete report CSV
This is the exact text used for the report download.
Complete input and import
Use a complete CSV or TSV exported by this workspace. Loading a file fills this text area; Apply changes the plan only after structural checks pass.
How to use this calculator
- Choose Units and Fill target profile. The reference profile changes with the total number of cables; Custom target uses your Custom fill target. Unit changes preserve physical diameters or leave the plan unchanged with an explanation.
- Enter each cable’s Outside diameter, including its insulation or outer jacket, then Current count and Add later. Cable label is optional. Planned count is current plus later additions; enter a multi-conductor cable once using its complete circular envelope, not once per internal conductor.
- Include Wheatland EMT reference sizes to compare the sourced nominal inside diameters. Add a custom Candidate label and Inside diameter when you have another circular clear opening. Trade size is a label, not the diameter used in the calculation.
- Compare current and planned fills with their separate target markers. Use Inspect for a candidate to read its status, percentage-point margin and contribution table. The smallest listed result identifies only the candidate diameter meeting the selected area target.
- Choose Capacity cable to investigate further copies after the entire planned bundle. Read the feasible count ranges and the next-one result together: a changing reference threshold can leave a gap, so the largest qualifying count does not mean every smaller addition qualifies.
- Choose Input format, then use Choose input file or Paste a complete conduit input file and Apply complete input to replace the plan atomically. Complete conduit input preserves the current plan for reuse. Download complete report has matching Complete report CSV text; a malformed custom candidate keeps valid comparisons but blocks that report until corrected.
The Formula
The mathematical logic powering this calculation is:
For round cable outside diameters dᵢ and conduit inside diameter D, S = Σ nᵢdᵢ² and area fill = 100S/D². Cable and conduit areas are πS/4 and πD²/4; π cancels from the fill comparison.
Planned count is Current count + Add later. The reference area target is 53% at one cable, 31% at two, and 40% at three or more; an empty reference bundle has no assigned target. A fixed target p remains explicit, including zero.
When S > 0 and p > 0, the area-derived minimum inside diameter is √(100S/p). This square root may be approximate; exact squared comparisons decide the listed candidates. A nonempty bundle at p = 0 has no finite qualifying diameter.
For k further copies of the selected cable after the planned bundle, evaluate 100(S + kd²)/D² against the target for N + k. Solve the count regimes separately and retain every feasible integer interval; do not assume all counts below a maximum qualify.
One inch is exactly 25.4 mm. All comparisons are conditional on the entered or sourced nominal dimensions. Neither the area-derived minimum nor a listed match proves physical packing, pulling feasibility or adopted-code compliance.Worked Example
If you input:
- Units: Millimetres (mm)
- Fill target profile: Reference · 53% / 31% / 40%
- Include Wheatland EMT reference sizes: Yes
- Cable label: Network cable
- Outside diameter: 5 mm
- Current count: 3
- Add later: 2
- Capacity cable: Network cable
Result:
Three current 5 mm cables occupy about 30.05% of the nominal 1/2-inch EMT inside area. With two more cables, planned fill is about 50.08%, above the selected 40% reference target. The smallest listed diameter meeting the planned area target is nominal 3/4-inch EMT, at about 28.54% fill. This is an area comparison, not an installation approval.
Frequently Asked Questions
How is conduit fill calculated?
For circular cables, the calculator sums count times outside diameter squared and divides by conduit inside diameter squared, then multiplies by 100. The common pi/4 factor cancels from the percentage. Exact decimal rational comparisons classify the entered area target; rounded display values do not decide whether it is met. Physical area values use pi and are shown approximately. Exact arithmetic does not make entered or nominal dimensions exact physical measurements.
Which diameter and cable count should I enter?
Enter the complete cable outside diameter including its insulation or jacket, using your measured or manufacturer-supplied dimension. Do not enter bare-conductor diameter, conductor area, or an AWG number. Count a multi-conductor cable once using its whole circular envelope. Noncircular cable shapes are outside this model. Current count and Add later are nonnegative whole numbers; zero-count groups may remain for a capacity query.
What does the reference profile mean?
The reference profile reproduces the 53%, 31% and 40% area comparisons for one, two, and three or more cables in PPI's 2021 handbook, Chapter 14, Table 1. It is dated reference guidance, not verification of the code adopted at an installation or its exceptions. Current and planned totals may select different thresholds. Use an explicit Fixed target for a separately chosen area comparison; this tool does not determine which rule applies to your installation.
Why can additional-cable capacity contain a gap?
The reference percentage changes when the final count becomes two or three. Adding one small cable can cross into the lower two-cable threshold, while adding another can enter the higher three-or-more threshold. The result therefore reports complete feasible integer ranges, whether the next one qualifies, and the continuous qualifying range from zero. These additions start after all entries in Add later. They describe area arithmetic, not cable packing or pulling feasibility.
Are trade sizes and the smallest listed candidate guaranteed to fit?
No. The EMT list uses nominal inside diameters from Wheatland document WEL-101625; a trade designation is not that inside diameter. Custom candidates use your entered dimensions. The smallest listed result keeps equal-diameter ties and means only that its area meets the chosen target. It does not establish actual clearance, shape packing, installation suitability or manufacturing tolerances. Invalid custom candidates make the smallest-listed conclusion incomplete rather than silently disappearing.
What happens with an empty bundle or a zero target?
An empty bundle occupies zero area. The reference profile has no threshold for zero cables, so the result states that the bundle is empty instead of assigning it a fictitious percentage limit. A fixed target remains explicit at zero count. At a fixed zero-percent target, a nonempty bundle cannot qualify at any finite candidate diameter. An invalid core cable or active target clears dependent results; a local candidate error leaves the other candidates inspectable.
What are the model limits and excluded checks?
The workspace accepts up to 24 circular cable groups and 12 custom candidates alongside ten optional nominal EMT sizes. Counts are whole numbers from zero to one million per current or added field; supported diameters are 0.000001 to 1000000 mm, with equivalent inch entries. These are numerical bounds. The model does not calculate ampacity, thermal derating, grounding, bends, pulling tension, jamming, air-blown installation requirements, code exceptions or physical packing. Its diagrams account for area and do not draw a verified cable arrangement.
Similar Calculators
AC Power & Power Factor Calculator
Calculate AC watts, vars, volt-amps and power factor for single-phase or balanced three-phase loads. Combine leading and lagging loads, compare an ideal target PF and export the ledger.
Ohm's Law Calculator
Calculate voltage, current, or resistance using Ohm's Law — enter any two values to find the third.
Equivalent Resistance Calculator
Solve a DC resistor network, including series, parallel and bridge connections. Inspect node voltages, branch currents, power and terminal tolerance bounds.
