Cabinet Refacing Cost & Material Planner
Count replacement doors and drawer fronts separately from the material covering the existing cabinet boxes. Measure visible ends, trim and a rectangular face frame. Compare two usable veneer stock sizes and entered quotes, inspect the grain-oriented cuts, and see how material, fronts and labor affect the modeled total.
Compare cabinet refacing costs
Count replacement fronts, measure the visible cabinet boxes and compare two stock sizes using real cutting layouts.
Cabinet refacing comparison
4 doors · 2 drawer fronts · 8.6875 ft² exposed box coverage
Option A · 24 × 72 in roll
$951.00
1 roll · $85.00 covering stock
Option B · 20 × 48 in sheet
$1,009.00
3 sheets · $135.00 covering stock
Option A costs $58.00 less for the listed scope.
Edit fronts and box measurements
Replacement fronts
Use the finished order size from your supplier. Doors and drawer fronts are priced separately from box covering stock.
Exposed side and trim pieces
Enter finished rectangles once each. Keep these measurements separate from the face frame below.
Edit stock and entered prices
Use stock dimensions after edge trimming. Enter width across grain and length along grain. Enter 0 for work included elsewhere or outside this scope.
Face frame and stock layouts
The plans place every cut in rows inside usable stock. Gray includes unused areas and the space between cuts.
Stiles are green. Rails are purple. The open areas use no veneer.
Option A · 1 roll
2.5521 ft² unused across all purchased stock units
Show Option A cuts on this stock unit
Cut 1 · End panel 1 · 18.5 × 30.5 in
0 in from left · 0 in from top
Cut 2 · End panel 1 · 18.5 × 30.5 in
0 in from left · 30.625 in from top
Cut 3 · Left stile · 2 × 30.5 in
18.625 in from left · 0 in from top
Cut 4 · Right stile · 2 × 30.5 in
20.75 in from left · 0 in from top
Cut 5 · Top rail · 2 × 27.5 in
18.625 in from left · 30.625 in from top · Quarter-turn
Cut 6 · Bottom rail · 2 × 27.5 in
20.75 in from left · 30.625 in from top · Quarter-turn
Option B · 3 sheets
10.5521 ft² unused across all purchased stock units
Show Option B cuts on this stock unit
Cut 1 · End panel 1 · 18.5 × 30.5 in
0 in from left · 0 in from top
Show scope and cost ledger
Ordered fronts
- Door 1 · 4 × 15 × 28 in
- Drawer front 2 · 2 × 14 × 6 in
Cabinet box pieces
8.6875 ft² installed · 9.4479 ft² including cut oversize
- End panel 1 · 2 × 18 × 30 in · Along height
- Left stile · 1 × 1.5 × 30 in · Along height
- Right stile · 1 × 1.5 × 30 in · Along height
- Top rail · 1 × 27 × 1.5 in · Along width
- Bottom rail · 1 × 27 × 1.5 in · Along width
Option A costs
- Doors
- $220.00
- Drawer fronts
- $56.00
- Stock
- $85.00
- Labor
- $500.00
- Other quoted cost
- $90.00
- Total
- $951.00
Option B costs
- Doors
- $192.00
- Drawer fronts
- $52.00
- Stock
- $135.00
- Labor
- $550.00
- Other quoted cost
- $80.00
- Total
- $1,009.00
Export the comparison
Show CSV text
How to use this calculator
- Enter the finished widths, heights and counts of doors and drawer fronts being ordered. If you are only covering the cabinet boxes, remove the front groups.
- Add visible end panels and trim. Enable the rectangular frame if useful and measure its outer edges, stile widths, rail heights and quantity.
- Enter the oversize per edge and separation between cuts. Select the grain direction in the installed orientation for each independently measured cover.
- Enter two usable stock sizes after edge trimming, and add the actual replacement-front prices, covering stock rate, labor and other quoted costs.
- Compare units and total costs. Use the drawings and exact cut positions or export the complete CSV.
The Formula
The mathematical logic powering this calculation is:
Replacement doors and drawer fronts use their finished ordering dimensions and group counts. The planner bills each group by count using its matching entered rate. It does not infer order dimensions from cabinet openings or calculate overlays, hinge locations, reveals or replacement fit. These separate ordered fronts do not consume box covering material.
Add finished exposed end panels and trim as independent rectangles. Enter each exposed surface once. The optional rectangular face frame uses two full-height side stiles, a top and a bottom rail running between those stiles, and an optional centered stile spanning the clear height between rails. Frame area equals outer width times outer height minus the combined openings. The method assigns each part of the frame to exactly one strip. Manual face strips can represent additional frames and irregular assemblies if each finished piece is measured separately.
Cut width and height are each the finished dimension plus twice the entered per-edge allowance. Stock dimensions are usable dimensions after edge trimming. Its width is measured across grain and its length along grain. A required grain along the face height keeps the height parallel to stock length. Grain along the face width turns the piece. With no orientation preference, either direction may be tried. The generated frame stiles have grain along height and generated rails have grain along width. The model checks grain axes while leaving pattern matching, bookmatching, edge treatments and material suitability to the project specification.
One repeatable layout sorts the finished pieces by their longest side, then area, then entry order. In that order it tries existing rows, a new row on existing stock, then a new stock unit. A row has the depth of its first cut. One entered separation gap is left between neighboring pieces in a row and between rows, with no added gap from an outer stock edge. The worksheet tests all permitted orientations at each placement. An individually blocked piece prevents a complete stock plan, even if raw area appears sufficient. The result is a feasible straight-row cut schedule when all parts fit, and another cutting layout may use fewer units. Unused area includes separation gaps and other residual usable stock. It does not imply that each remnant has reusable dimensions.
Modeled cost is door count times door rate, plus drawer front count times drawer rate, plus placed stock unit count times stock rate, plus entered labor and other project costs. Compare the same scope under both quotes. An absent front category has no price charge, and a width, length or grain incompatibility prevents a complete total. A complete total covers the entered work and prices only. No local, tax, labor-market or product-price estimate is implied.
Use up to four replacement-front groups, four rectangular covering groups, and one measured frame geometry repeated up to eight times. Fronts and cover groups support one to twelve pieces each. Finished dimensions accept 0.125–120 in, stile and rail measurements 0.125–24 in, with an optional zero center stile. Cut oversize is 0–3 in per edge and separation 0–2 in. Usable stock accepts 1–144 in across and 1–1,200 in along the grain. Geometry uses thousandths of an inch and exact integers for cents. Frame positions can include half-thousandths when the center stile divides an odd number of units.Method sources
- HUD Residential Rehabilitation Guide · cabinet refacing and replacement components
- WalzCraft · cabinet refacing material scopes and exposed faces, ends, rails and stiles
- VeneerSupplies · backed veneer width across grain and length along grain
- Nieu Cabinet Doors · ordering measurement, overlays and reveals
Worked Example
If you input:
- Ordered fronts: Four 15 × 28 inch doors and two 14 × 6 inch drawer fronts
- Box surfaces: Two 18 × 30 inch ends and one 30 × 30 inch frame with 1.5 inch rails and stiles
- Cut allowance: 0.25 inch per edge and 0.125 inch between cuts
- Option A: 24 × 72 inch roll at $85, $55 per door, $28 per drawer front, $500 labor and $90 other
- Option B: 20 × 48 inch sheets at $45, $48 per door, $26 per drawer front, $550 labor and $80 other
Result:
The existing boxes need 1,251 in² of finished cover, or 1,360.5 in² before trimming the oversized blanks. One roll fits all six blanks in Option A, for a modeled project cost of $951. Three sheets fit the same scope in Option B, bringing its modeled total to $1,009. Option A is $58 lower for the entered scope.
Frequently Asked Questions
What does the cabinet refacing total cover?
It adds the typed unit prices for ordered doors, drawer fronts and the number of finishing sheets or rolls used by the plan, plus entered labor and other costs. Include hardware, delivery, tax or similar quoted charges in Other when they belong in the comparison.
How should I measure cabinet doors for refacing?
Enter the confirmed final ordering sizes from your supplier. Closure type, overlay, reveal and hinges can change the relationship between an opening and a replacement door, and the measurement conventions vary by product.
Are replacement front dimensions added to veneer stock?
The planner treats doors and drawer fronts as finished ordered items priced by count. Only box coverings, such as measured end panels, trim, stiles and rails, enter the stock layouts.
Why do two stock pieces with the same area fit differently?
A rectangular cut must fit across and along the usable stock in a permitted grain direction. For example, a 14 × 27 inch vertical-grain piece fits 14 inches across by 27 inches along. On 27 × 14 inch stock it needs a quarter-turn, which changes the grain orientation on the installed panel.
Are the sheet and roll counts guaranteed minimums?
The planner constructs physically separated straight-row layouts using one repeatable placement order. Different part orderings or nesting geometries can change the number of units. The worksheet reports the units from the layout it shows.
Can I mix different covering materials for end panels and frame strips?
Each option assumes one compatible stock type for every box cover. Divide parts into separate worksheets when end panels and face strips use different backing, thickness, grain rules or product systems.
Similar Calculators
Kitchen Remodel Cost & Quantity Planner
Calculate kitchen remodeling costs from measured cabinet runs, countertops and backsplashes. Compare quotes, bundled scope, gross/net area billing and budgets with CSV.
Plywood Cut Planner
Plan rectangular plywood cuts with kerf and rotation constraints. Compare eight sheet layouts and inspect parts, cuts and remnants.
Paint Coverage Calculator
Estimate paintable wall area, paint needed, gallons to buy, and project cost with room-by-room deductions.
