Board and Batten Layout Calculator
Plan a decorative wall pattern from its actual dimensions. Compare equal gaps and inspect the straight pieces remaining around openings.
Place every board with confidence.
Find an equal-gap pattern, see its exact board positions and plan straight pieces around windows, doors and keep-clear areas.
7 vertical battens; clear gap 530 mm; 9 retained pieces.
Treatment area and boards
Changing units preserves physical dimensions and source text.
Use the actual visible width of a board.
Enter decimals or fractions such as 3/8 and 12 3/8. The treatment rectangle can cover a whole wall or a shorter wainscot area.
Choose your pattern
Whole number, excluding any left and right end battens. Up to 100 total vertical battens.
Used for comparisons; it does not replace your chosen count.
Zero means no bottom rail.
Zero means no top rail.
Vertical boards fit between the rails. Equal gaps include an open end when its end batten is excluded.
Openings and keep-clear areas
Applied to every side of each opening. Enter your own required allowance.
An opening interrupts a board across its entire face width. The pattern stays fixed; the tool produces straight rectangular pieces.
Positions use the treatment’s bottom-left corner. Negative positions and partly outside openings are supported.
Your current pattern
Equal clear gap
530 mm
5 interior + 2 end battens · 7 vertical boards
- Center pitch
- 590 mm
- Retained straight pieces
- 9
- Batten length retained
- 15.4 m
- Rail length retained
- 7.2 m
0 interrupted boards · 0 completely omitted. Lengths describe installed pieces; they do not include stock waste or saw kerf.
Compare with your preferred gap
Preference: 500 mm. Choose a count explicitly to change the pattern.
Closest clear gap
530 mm
5 interior · 7 total battens
At or below preference
≈445.714285714 mm
6 interior · 8 total battens
Compare all 59 fitting counts
| Interior / total battens | Equal clear gap | Center pitch | Gap difference | Closest rank | At or below preference | Apply |
|---|---|---|---|---|---|---|
| 0 / 2 | 3480 mm | 3540 mm | 2980 mm | 59 | No | |
| 1 / 3 | 1710 mm | 1770 mm | 1210 mm | 58 | No | |
| 2 / 4 | 1120 mm | 1180 mm | 620 mm | 57 | No | |
| 3 / 5 | 825 mm | 885 mm | 325 mm | 12 | No | |
| 4 / 6 | 648 mm | 708 mm | 148 mm | 4 | No | |
| 5 / 7 | 530 mm | 590 mm | 30 mm | 1 | No | |
| 6 / 8 | ≈445.714285714 mm | ≈505.714285714 mm | ≈54.2857142857 mm | 2 | Yes | |
| 7 / 9 | 382.5 mm | 442.5 mm | 117.5 mm | 3 | Yes | |
| 8 / 10 | ≈333.333333333 mm | ≈393.333333333 mm | ≈166.666666667 mm | 5 | Yes | |
| 9 / 11 | 294 mm | 354 mm | 206 mm | 6 | Yes | |
| 10 / 12 | ≈261.818181818 mm | ≈321.818181818 mm | ≈238.181818182 mm | 7 | Yes | |
| 11 / 13 | 235 mm | 295 mm | 265 mm | 8 | Yes | |
| 12 / 14 | ≈212.307692308 mm | ≈272.307692308 mm | ≈287.692307692 mm | 9 | Yes | |
| 13 / 15 | ≈192.857142857 mm | ≈252.857142857 mm | ≈307.142857143 mm | 10 | Yes | |
| 14 / 16 | 176 mm | 236 mm | 324 mm | 11 | Yes | |
| 15 / 17 | 161.25 mm | 221.25 mm | 338.75 mm | 13 | Yes | |
| 16 / 18 | ≈148.235294118 mm | ≈208.235294118 mm | ≈351.764705882 mm | 14 | Yes | |
| 17 / 19 | ≈136.666666667 mm | ≈196.666666667 mm | ≈363.333333333 mm | 15 | Yes | |
| 18 / 20 | ≈126.315789474 mm | ≈186.315789474 mm | ≈373.684210526 mm | 16 | Yes | |
| 19 / 21 | 117 mm | 177 mm | 383 mm | 17 | Yes | |
| 20 / 22 | ≈108.571428571 mm | ≈168.571428571 mm | ≈391.428571429 mm | 18 | Yes | |
| 21 / 23 | ≈100.909090909 mm | ≈160.909090909 mm | ≈399.090909091 mm | 19 | Yes | |
| 22 / 24 | ≈93.9130434783 mm | ≈153.913043478 mm | ≈406.086956522 mm | 20 | Yes | |
| 23 / 25 | 87.5 mm | 147.5 mm | 412.5 mm | 21 | Yes | |
| 24 / 26 | 81.6 mm | 141.6 mm | 418.4 mm | 22 | Yes | |
| 25 / 27 | ≈76.1538461538 mm | ≈136.153846154 mm | ≈423.846153846 mm | 23 | Yes | |
| 26 / 28 | ≈71.1111111111 mm | ≈131.111111111 mm | ≈428.888888889 mm | 24 | Yes | |
| 27 / 29 | ≈66.4285714286 mm | ≈126.428571429 mm | ≈433.571428571 mm | 25 | Yes | |
| 28 / 30 | ≈62.0689655172 mm | ≈122.068965517 mm | ≈437.931034483 mm | 26 | Yes | |
| 29 / 31 | 58 mm | 118 mm | 442 mm | 27 | Yes | |
| 30 / 32 | ≈54.1935483871 mm | ≈114.193548387 mm | ≈445.806451613 mm | 28 | Yes | |
| 31 / 33 | 50.625 mm | 110.625 mm | 449.375 mm | 29 | Yes | |
| 32 / 34 | ≈47.2727272727 mm | ≈107.272727273 mm | ≈452.727272727 mm | 30 | Yes | |
| 33 / 35 | ≈44.1176470588 mm | ≈104.117647059 mm | ≈455.882352941 mm | 31 | Yes | |
| 34 / 36 | ≈41.1428571429 mm | ≈101.142857143 mm | ≈458.857142857 mm | 32 | Yes | |
| 35 / 37 | ≈38.3333333333 mm | ≈98.3333333333 mm | ≈461.666666667 mm | 33 | Yes | |
| 36 / 38 | ≈35.6756756757 mm | ≈95.6756756757 mm | ≈464.324324324 mm | 34 | Yes | |
| 37 / 39 | ≈33.1578947368 mm | ≈93.1578947368 mm | ≈466.842105263 mm | 35 | Yes | |
| 38 / 40 | ≈30.7692307692 mm | ≈90.7692307692 mm | ≈469.230769231 mm | 36 | Yes | |
| 39 / 41 | 28.5 mm | 88.5 mm | 471.5 mm | 37 | Yes | |
| 40 / 42 | ≈26.3414634146 mm | ≈86.3414634146 mm | ≈473.658536585 mm | 38 | Yes | |
| 41 / 43 | ≈24.2857142857 mm | ≈84.2857142857 mm | ≈475.714285714 mm | 39 | Yes | |
| 42 / 44 | ≈22.3255813953 mm | ≈82.3255813953 mm | ≈477.674418605 mm | 40 | Yes | |
| 43 / 45 | ≈20.4545454545 mm | ≈80.4545454545 mm | ≈479.545454545 mm | 41 | Yes | |
| 44 / 46 | ≈18.6666666667 mm | ≈78.6666666667 mm | ≈481.333333333 mm | 42 | Yes | |
| 45 / 47 | ≈16.9565217391 mm | ≈76.9565217391 mm | ≈483.043478261 mm | 43 | Yes | |
| 46 / 48 | ≈15.3191489362 mm | ≈75.3191489362 mm | ≈484.680851064 mm | 44 | Yes | |
| 47 / 49 | 13.75 mm | 73.75 mm | 486.25 mm | 45 | Yes | |
| 48 / 50 | ≈12.2448979592 mm | ≈72.2448979592 mm | ≈487.755102041 mm | 46 | Yes | |
| 49 / 51 | 10.8 mm | 70.8 mm | 489.2 mm | 47 | Yes | |
| 50 / 52 | ≈9.41176470588 mm | ≈69.4117647059 mm | ≈490.588235294 mm | 48 | Yes | |
| 51 / 53 | ≈8.07692307692 mm | ≈68.0769230769 mm | ≈491.923076923 mm | 49 | Yes | |
| 52 / 54 | ≈6.79245283019 mm | ≈66.7924528302 mm | ≈493.20754717 mm | 50 | Yes | |
| 53 / 55 | ≈5.55555555556 mm | ≈65.5555555556 mm | ≈494.444444444 mm | 51 | Yes | |
| 54 / 56 | ≈4.36363636364 mm | ≈64.3636363636 mm | ≈495.636363636 mm | 52 | Yes | |
| 55 / 57 | ≈3.21428571429 mm | ≈63.2142857143 mm | ≈496.785714286 mm | 53 | Yes | |
| 56 / 58 | ≈2.10526315789 mm | ≈62.1052631579 mm | ≈497.894736842 mm | 54 | Yes | |
| 57 / 59 | ≈1.03448275862 mm | ≈61.0344827586 mm | ≈498.965517241 mm | 55 | Yes | |
| 58 / 60 | 0 mm | 60 mm | 500 mm | 56 | Yes |
Inspect the layout
Measured from the bottom-left corner. Blue pieces are retained trim; dashed outlines show the original boards.
- Width · x from left
- 0 mm to 3600 mm
- Height · y from bottom
- 0 mm to 2400 mm
- Blue solid: retained pieces
- Gray dashed: nominal boards
- Gray crosshatching: openings
- Amber hatching: keep-clear area
- Purple dashed: inspection
Outlines identify edges; their thickness is not material. Very thin or closely spaced features may require the coordinate tables.
Left end batten
- x
- 0 mm
- y
- 100 mm
- width
- 60 mm
- height
- 2200 mm
1 retained pieces · retained length 2200 mm. Center: x 30 mm, y 1200 mm.
Coordinates and cut schedule
Board positions · 9
| Board | x | y | Width | Height | Center x | Center y | Retained length | Pieces |
|---|---|---|---|---|---|---|---|---|
| Left end batten | 0 mm | 100 mm | 60 mm | 2200 mm | 30 mm | 1200 mm | 2200 mm | 1 |
| Interior batten 1 | 590 mm | 100 mm | 60 mm | 2200 mm | 620 mm | 1200 mm | 2200 mm | 1 |
| Interior batten 2 | 1180 mm | 100 mm | 60 mm | 2200 mm | 1210 mm | 1200 mm | 2200 mm | 1 |
| Interior batten 3 | 1770 mm | 100 mm | 60 mm | 2200 mm | 1800 mm | 1200 mm | 2200 mm | 1 |
| Interior batten 4 | 2360 mm | 100 mm | 60 mm | 2200 mm | 2390 mm | 1200 mm | 2200 mm | 1 |
| Interior batten 5 | 2950 mm | 100 mm | 60 mm | 2200 mm | 2980 mm | 1200 mm | 2200 mm | 1 |
| Right end batten | 3540 mm | 100 mm | 60 mm | 2200 mm | 3570 mm | 1200 mm | 2200 mm | 1 |
| Bottom rail | 0 mm | 0 mm | 3600 mm | 100 mm | 1800 mm | 50 mm | 3600 mm | 1 |
| Top rail | 0 mm | 2300 mm | 3600 mm | 100 mm | 1800 mm | 2350 mm | 3600 mm | 1 |
Clear spans · 6
| Gap | Start x | Clear width |
|---|---|---|
| 1 | 60 mm | 530 mm |
| 2 | 650 mm | 530 mm |
| 3 | 1240 mm | 530 mm |
| 4 | 1830 mm | 530 mm |
| 5 | 2420 mm | 530 mm |
| 6 | 3010 mm | 530 mm |
Retained pieces · 9
| Piece / board | x | y | Width | Height | Face width | Cut length |
|---|---|---|---|---|---|---|
| batten-left:segment-1batten-left | 0 mm | 100 mm | 60 mm | 2200 mm | 60 mm | 2200 mm |
| batten-interior-1:segment-1batten-interior-1 | 590 mm | 100 mm | 60 mm | 2200 mm | 60 mm | 2200 mm |
| batten-interior-2:segment-1batten-interior-2 | 1180 mm | 100 mm | 60 mm | 2200 mm | 60 mm | 2200 mm |
| batten-interior-3:segment-1batten-interior-3 | 1770 mm | 100 mm | 60 mm | 2200 mm | 60 mm | 2200 mm |
| batten-interior-4:segment-1batten-interior-4 | 2360 mm | 100 mm | 60 mm | 2200 mm | 60 mm | 2200 mm |
| batten-interior-5:segment-1batten-interior-5 | 2950 mm | 100 mm | 60 mm | 2200 mm | 60 mm | 2200 mm |
| batten-right:segment-1batten-right | 3540 mm | 100 mm | 60 mm | 2200 mm | 60 mm | 2200 mm |
| rail-bottom:segment-1rail-bottom | 0 mm | 0 mm | 3600 mm | 100 mm | 100 mm | 3600 mm |
| rail-top:segment-1rail-top | 0 mm | 2300 mm | 3600 mm | 100 mm | 100 mm | 3600 mm |
Grouped cut lengths · 2
| Group | Face width | Cut length | Quantity | Combined length | Area |
|---|---|---|---|---|---|
| 1 | 60 mm | 2200 mm | 7 | 15.4 m | 0.924 m² |
| 2 | 100 mm | 3600 mm | 2 | 7.2 m | 0.72 m² |
Finished rectangular segments only. Stock lengths, saw kerf, offcuts and installation tolerances require a separate plan.
Where the trim area goes
- Nominal trim area
- 1.644 m²
- Retained trim
- 1.644 m²
- Original openings within trim
- 0 m²
- Added clearance within trim
- 0 m²
- Extra full-width interruption
- 0 m²
- Reconciliation difference
- 0 m²
Retained trim + original opening intersection + added clearance + extra full-width interruption = nominal trim area. Opening and clearance deductions count only their intersections with trim; a full-width interruption can omit additional material beside an opening.
Save or restore a plan
Save reusable inputs, including unfinished drafts, or download a complete calculation report. Imported inputs are previewed before they replace this plan.
Selectable reusable input
Selectable report CSV
Use this tool’s reusable input, in the selected format. A result report is not an input file.
Planning assumptions
This is a decorative geometry plan. It does not determine fastening, structural strength, electrical clearance, exterior weatherproofing or product-specific installation requirements. Check actual dimensions and fit on site.
Calculation conventions and limits
- The rectangle is the treatment area; all widths are actual entered face widths.
- Openings and clearance interrupt entire strip widths without moving the equal-gap grid.
- This is a geometric segment schedule, without stock nesting, saw kerf, fastening or exterior cladding compliance.
How to use this calculator
- Enter Treatment width, Treatment height, Batten face width and Length unit. Use actual face dimensions. Complete decimals, scientific notation, simple fractions such as 3/8 and mixed fractions such as 12 3/8 are supported within the stated limits; a sign applies to the entire mixed value.
- Set Interior batten count, Left end batten and Right end batten. The count excludes the separately selected ends. Inspect the current clear gap and center pitch. An overfull count shows the required width and deficit while keeping fitting alternatives available.
- Enter Preferred clear gap and compare the closest layout with the first count at or below that gap. Use this count explicitly adopts the recommendation. Preference changes and opening edits do not silently replace your authored count.
- Set Bottom rail height and Top rail height; zero omits a rail. Vertical battens fit between their inside edges. Enter openings from the bottom-left origin and set Opening clearance. The original layout stays fixed while full-width straight pieces are removed around positive overlaps.
- Inspect the elevation and its board, gap and segment ledgers. Overlapping openings are counted once. Review original-opening, extra-clearance and full-width-interruption deductions separately. Exact coordinates remain available when narrow features are hard to distinguish on screen.
- Use Reusable input format and Paste reusable input to stage a complete CSV or TSV plan, then apply it explicitly. Reusable input preserves unfinished drafts. A complete report requires valid inputs and can honestly record a count that does not fit; the segment schedule does not include kerf, stock offcuts or installation instructions.
The Formula
The mathematical logic powering this calculation is:
Let W be treatment width, b actual batten face width, N the interior batten count and E the number of included end battens. Clear gap g = [W − (N + E)b] / (N + 1). Interior batten starts are left × b + g + i(b + g), for i = 0,…,N − 1, where left is 1 when the left end batten is included. Included ends start at 0 and W − b. Center pitch is b + g when at least two vertical battens exist.
Compare every fitting integer N from 0 through 100 − E. Closest minimizes |g − preferred gap|, with fewer interior battens winning an exact tie. At-or-below selects the smallest fitting N with g no greater than the preference. A negative current gap means that authored count does not fit; alternatives remain available. No recommendation is adopted automatically.
For height H, bottom rail B and top rail T, vertical battens span y = B through H − T, with B + T < H. Positive rails span the full treatment width. Coordinates start at the treatment rectangle's bottom-left corner.
Expand each opening by the entered clearance, then clip it to the treatment. Positive overlap across a board removes the overlapping interval along its full length direction. Union overlapping or touching blocked intervals before taking their positive-length complement. This creates full-width straight segments rather than notches; exact edge contact removes nothing.
Nominal trim area = retained trim area + original opening union intersecting trim + additional clearance intersection + extra omission caused by full-width interruption. The four terms are disjoint, and the conservation residual is exactly zero. Group retained pieces by exact face width and length; linear totals do not determine stock purchases.
Geometry, unit conversion, gap rankings and accounting use exact rational values. One inch is exactly 25.4 mm. Display rounding never chooses a layout or removes a segment. This is decorative geometry, not exterior installation, stock nesting or a saw-cut plan.Worked Example
If you input:
- Length unit: mm
- Treatment width: 3600 mm
- Treatment height: 2400 mm
- Batten face width: 60 mm
- Interior batten count: 5
- Left end batten: Include
- Right end batten: Include
- Preferred clear gap: 500 mm
- Bottom rail height: 100 mm
- Top rail height: 100 mm
- Opening clearance: 0 mm
- Openings: None
Result:
Seven vertical battens leave six clear gaps of 530 mm, with center pitch 590 mm. Their left edges are 0, 590, 1180, 1770, 2360, 2950 and 3540 mm. Each vertical is 2200 mm long between the rails. Nine straight pieces retain 15.4 m of battens plus 7.2 m of rails, with trim area 1.644 m². Five interior battens give the closest gap to 500 mm; six give the first gap at or below it: 3120/7 mm, approximately 445.714286 mm. Use this count changes the current layout explicitly. These dimensions are illustrative, not installation recommendations.
Frequently Asked Questions
Is clear gap the same as center-to-center spacing?
Clear gap is the empty width between neighboring batten edges or between a batten and an untrimmed panel edge. Center pitch includes one actual batten width as well as the gap. The model reports pitch only when at least two nominal vertical battens exist. It retains zero-width gap records when battens touch, and an empty vertical pattern still has one clear span equal to the treatment width.
Does Interior batten count include the boards at the ends?
No. Left and right end battens are independent choices, and each included end adds one vertical board. At most 100 total vertical battens are supported. The pattern has N + 1 equal clear spaces for N interior battens, including a wall-edge space where an end batten is excluded. Top and bottom rails are separate horizontal strips and do not change the gap comparison.
How do Closest and At-or-below choose a count?
Every fitting count within the declared bound is checked exactly. Closest minimizes absolute difference from your preferred clear gap, choosing fewer interior battens on an exact tie. At-or-below chooses the smallest count whose gap does not exceed the preference. Simply rounding an inverse formula can choose the wrong closest layout. Neither recommendation moves your current pattern until you use its count, and no solution within the count bound is reported explicitly.
Should I enter nominal lumber sizes, and can I use fractional inches?
Enter the actual measured face width used in your layout; the calculator does not infer a dimension from a nominal board name. Simple fractions and mixed fractions are exact inputs, and changing units preserves the original measurements exactly. For example, -1 1/2 means minus one and a half. Counts require whole-number digits. Exact arithmetic prevents rounding from changing placement, but it does not make field measurements exact or walls perfectly square.
What happens when an opening overlaps only part of a board's width?
The model interrupts the whole board width for the overlapping interval along its length. A vertical batten can become separate straight pieces above and below an opening; a rail can become pieces to its left and right. This deliberately omits additional material beside a partial-width opening instead of proposing a notch. The report separates that additional omission from actual opening and clearance intersections. Overlaps are unioned, and edge contact alone removes nothing.
Does total length tell me how many stock boards to buy?
It reports retained finished geometry, with batten and rail lengths separated and identical rectangles grouped by both face width and length. Stock lengths, saw kerf, joins, offcut reuse, defects and installation allowances are not modeled. A completely interrupted board has no retained piece but remains in the nominal ledger. Do not turn summed lengths into a purchasing claim; sheet nesting and siding pack estimates are separate workflows in the related tools.
Can I use this as an exterior board-and-batten installation plan?
The result is a decorative rectangular treatment layout. Exterior products may require battens at panel seams, specified framing, fastening, flashing and movement details that this model does not evaluate. Openings and entered clearance are geometric inputs, not electrical or building-code clearances. Manufacturer guidance supplies terminology and the basic spacing idea; the whole-width interruption and finite count comparison are explicitly the calculator's own planning conventions.
Similar Calculators
Siding Calculator
Estimate siding for walls and gables with validated door and window openings, exposed pack coverage, waste, whole-pack quantities and material costs.
Plywood Cut Planner
Plan rectangular plywood cuts with kerf and rotation constraints. Compare eight sheet layouts and inspect parts, cuts and remnants.
Unit Converter
Convert between units of length, weight, volume, and area — all in one tool.
