Walk-In Shower Opening, Door Swing & Quote Planner

See which measured dimensions constrain two walk-in shower proposals. Enter the finished alcove at several heights and each proposed door’s documented opening range. Compare stated usable passage and, for a simple pivot, map floor obstacles against the entered circular sweep. Keep written costs independent from geometric checks.

Measured opening

Compare shower door fit, swing and quotes

Check the finished opening, usable walk-through and floor space for two written shower proposals.

Finished opening and quoted fit

Sampled opening widths
39.75 in to 40 in
Available opening height
78 in

Proposal A

Misses an entered check

Opening dimensions
Within entered bounds
Written charges
$1,750.00
Stated walk-through
17.5 in
Clear-width margin
6.5 in short

Proposal B

Misses an entered check

Opening dimensions
Within entered bounds
Written charges
$2,210.00
Stated walk-through
30 in
Clear-width margin
6 in spare

Review the measured opening, passage and swing checks before comparing prices.

Door sweep and floor obstacles

The shared plan uses the threshold as Y = 0. Positive Y extends into the bathroom. The pivot sector shows the entered circular clearance. Hatched obstacles overlap that sector.

Plan axes · X 0 in to 39.75 in · Y 0 in to 30 in

Proposal A · No modeled arc
Proposal A, Sliding, No modeled arc

Sliding leaf has no modeled exterior arc.

Proposal B · Sweep overlaps
Proposal B, Pivot toward right, Sweep overlaps

Pivot toward right · pivot X 0 in · radius 30 in

Vanity corner
Overlaps sweep

Measured widths and product limits

Width at 0 in high
39.75 in · left 0 in · right 39.75 in
Width at 39 in high
39.875 in · left 0.0625 in · right 39.9375 in
Width at 78 in high
40 in · left 0.125 in · right 40.125 in
Sampled jamb spans
Left 0.125 in · right 0.375 in

Proposal A

Entered opening range
37 in to 40 in
Minimum width margin
2.75 in spare
Maximum width margin
At limit
Opening height margin
0.25 in spare
Left jamb margin
No limit entered
Right jamb margin
No limit entered

Published possible passage 14.875 in to 17.875 in. Use the stated width for this proposal and measured site.

Proposal B

Entered opening range
39 in to 42 in
Minimum width margin
0.75 in spare
Maximum width margin
2 in spare
Opening height margin
4.5 in spare
Left jamb margin
No limit entered
Right jamb margin
No limit entered

Published possible passage 29.3125 in to 32.9375 in. Use the stated width for this proposal and measured site.

Edit opening, obstacles and quotes

Measured finished opening

Start at the threshold and end at the measured free height. Use a common vertical datum for left and right offsets. Add an intermediate station where the opening may narrow or widen.

Floor obstacles at swing height

Use the opening X datum again. The threshold is Y = 0. Positive Y extends into the bathroom. Enter rectangular footprints for objects that reach the modeled swing height.

Proposal A dimensions and charges

Jamb limits and the published possible passage bounds are optional. Enter both passage bounds together when the documents supply them.

Proposal B dimensions and charges

Jamb limits and the published possible passage bounds are optional. Enter both passage bounds together when the documents supply them.

Written charges and export

Included adds no separate amount. An unpriced line keeps the complete total open.

Proposal A

Door and glass
$640.00
Base or finish work
$550.00
Entry transition
$180.00
Repair scope
$240.00
Setup and disposal
$140.00

Proposal B

Door and glass
$1,100.00
Base or finish work
$550.00
Entry transition
$180.00
Repair scope
$240.00
Setup and disposal
$140.00
Download shower comparison CSV
View selectable CSV

How to use this calculator

  1. Enter the measured left and right jamb at the threshold, top and any important intermediate heights.
  2. Enter each proposed door’s documented width range and required free height. Include a side-specific jamb limit only when supplied.
  3. Enter the clear passage specified for each proposed installation and your requested pass-through width.
  4. For a documented simple pivot, enter its location and effective radius. Add measured obstacles in the same floor coordinates.
  5. Compare the sweep and measurement details, then enter the written charges and download the comparison.

The Formula

The mathematical logic powering this calculation is:

Enter two to five measured stations from the threshold at 0 in to the top of the available opening. Each sampled width is the right edge minus the left edge on a common lateral datum. Compare the smallest and largest widths with the product’s entered range. Compare the highest station with the required free opening height. The measured span of either jamb is its maximum measured X offset minus its minimum. Compare those side-specific spans with the separately entered limits where documented. Equal dimensions meet a closed limit. Sampling captures the heights entered, so add a station at a known intermediate narrowing or widening.

Enter the usable walk-through quoted for the specific opening. The clear margin is the stated width minus your entered target. Published possible widths remain a separate reference range. When a quote has no stated width for the project, the clear comparison is pending. The worked examples use archived Kohler specification dimensions for the published opening limits. The stated project-specific clear widths and pivot dimensions are illustrative separate inputs.

For a simple one-direction 90° pivot, put the pivot on the threshold and use a written or measured effective radius. Positive Y runs into the bathroom. Translate the obstacle into that pivot’s coordinates and reflect the X axis for a leftward swing. Check its closest point in the relevant closed quadrant. An obstacle that exceeds the radius at its closest point clears the geometric sector. Exact contact with the circle, or contact along a radial edge with no positive overlap, is a separate review result. An obstacle with positive extent in the quadrant and distance strictly smaller than the radius overlaps. Sliding uses no modeled exterior quarter-arc. Enter only obstacles that extend through the modeled swing height.

Written glass, base or finish, entry transition, repair, and setup charges are entered independently in USD. Included adds zero incremental cost. Missing or unpriced scope keeps the complete total open. Compare complete prices after the entered aperture, clear passage and modeled sweep show no unresolved misses or contact. The calculation handles measured geometry and entered product or job limits. Curved openings, irregular swing or handle motion, wall or base installation, structural support, drains and accessibility approval are outside the model.

Enter inch measurements with up to four decimals. Opening widths, heights and pivot radius are bounded at 120 in. Obstacles support signed coordinates from −240 in to 240 in. Written item prices are nonnegative with two decimal places.

Worked Example

If you input:

  • Finished opening: 39.75, 39.875 and 40 in sampled widths, 78 in high, with a 24 in requested passage.
  • Proposal A: Sliding door with a documented 37–40 in opening range and an illustrative 17.5 in stated passage. Written charges $1,750.
  • Proposal B: Pivot door with a documented 39–42 in opening range, illustrative 30 in passage and 30 in effective radius. The nearest entered obstruction is 18 in across and 23.999 in into the room. Written charges $2,210.

Result:

Both proposals meet their entered opening width and height limits. A misses the requested clear passage by 6.5 in. B has 6 in of passage to spare but its modeled sweep overlaps the entered obstacle. The worksheet shows written totals independently and withholds the price comparison for compatible geometry.

Frequently Asked Questions

Why can the door fit but provide too little usable passage?

The finished opening includes panel, frame or track positions. The usable walk-through is measured with the door open and depends on the proposed panel arrangement.

Can a published width range substitute for an actual walk-through measurement?

The range describes the product’s possible clear widths. Use the quoted clear width for the specific opening or mark that number unavailable.

Why measure each jamb separately?

Both jambs can shift together and leave the width unchanged. Independent offsets capture sampled side movement for each entered jamb limit.

What does a sweep touching an obstacle mean?

The entered quarter-circle and rectangle touch without sharing any positive area. Review the exact contact separately from a modeled conflict or clearance.

Are there prices for a shower remodel in my area?

Enter actual written prices or your own planning amounts. The worked example uses editable illustrative charges.

Similar Calculators