TV Mount Height & Sightline Calculator

Estimate where a TV screen can sit on the wall using the screen diagonal, the console height, and measured eye positions from two seats. Each screen gets a feasible center range or an explanation of the conflicting limits. See the screen and sightlines at the proposed height or at the closest point in the feasible range.

Two screens and two seats

Plan the height of a wall-mounted TV

Compare two screen sizes against measured room clearance and the sightline limits you set for each seat.

Feasible screen heights

Room and seat limits define each feasible range. Your proposed center is 51 in.

Screen A · 55 in diagonal

47.9367 in wide × 26.9644 in tall

Closest feasible center

48.4534 in

Feasible range 41.4822 in to 48.4534 in

Bottom 34.9712 in · top 61.9356 in

Minimum set by Console plus gap. Maximum set by Seat B.

The proposed center falls outside at least one entered constraint.

Screen B · 85 in diagonal

74.0839 in wide × 41.6722 in tall

No feasible center

The minimum center is 48.8361 in and the maximum is 48.4534 in, a gap of 0.38273 in.

Minimum set by Console plus gap. Maximum set by Seat B.

The proposed center falls outside at least one entered constraint.

Screen A closest feasible center 48.4534 in. Screen B has no feasible center.

Room and seats

Measure heights from the floor and horizontal distance to the screen plane.

Seat A
Seat B

Enter your own maximum angles from the horizontal line through each seat’s eye height.

Screen sizes

Enter the display area’s diagonal and aspect ratio. Use outer dimensions separately for furniture or installation planning.

Screen A
Screen B

Side-view sightlines

Sightlines run from each eye position to the screen center. Horizontal distance and elevation have separate scales.

Screen A center 48.4534 in · bottom limit 28 in · top limit 76 in

Seat A · solid sightline
+4.4395° · Within entered angle
41 in eye height · 96 in distance
Seat B · dashed sightline
+9° · Within entered angle
38 in eye height · 66 in distance
Center bounds for Screen A
ConstraintMinimumMaximum
Room41.4822 in62.5178 in
Seat A27.5081 in61.4054 in
Seat B26.3624 in48.4534 in

Export the geometry

Save both screen sizes, position bounds and sightline angles.

Download TV height CSV
Show selectable CSV

How to use this calculator

  1. Start with One size fits example or Two sizes fit example. In Room and seats, choose Room measurement unit and enter the Console top, Gap above console, Usable wall top and Proposed screen center.
  2. Measure each seated eye height from the floor and horizontal distance to the screen plane. Set the maximum upward and downward angles you want to test for Seat A and Seat B.
  3. In Screen sizes, enter the diagonal in inches and the aspect width and height for each screen.
  4. Read Feasible screen heights for the nearest allowed center and its bottom and top edges. If a screen has no feasible center, use the controlling limits to see where the room and seat requirements conflict.
  5. Use Screen in diagram and Center in diagram to view both choices. Read the sightline angles and center bounds by seat, then Download TV height CSV for the geometry.

The Formula

The mathematical logic powering this calculation is:

For screen diagonal D and aspect width w and height h, visible width is D × w/√(w² + h²) and visible height H is D × h/√(w² + h²). At screen center C, bottom is C − H/2 and top is C + H/2. The room’s allowable interval for C starts at console top + clearance gap + H/2 and ends at usable wall top − H/2.
For an eye at height E, horizontal distance d from the screen plane, and user-entered maximum upward and downward angles u and v, the center interval is [E − d tan(v), E + d tan(u)]. The measured center sightline is atan2(C − E, d) in degrees, positive upward and negative downward. Angles refer to the center of an upright screen.
The feasible range uses the largest lower limit and smallest upper limit across the room and both seats. When the lower limit exceeds the upper limit, the chart and table show their separation and identify the controlling constraints. With a feasible range, the closest center is the proposed height if it is within that range, or the nearest endpoint otherwise. Numerical comparisons allow only small floating-point roundoff at mathematical equality.
Room and seat inputs may use inches or centimeters, with 1 inch exactly 2.54 cm. Switching units preserves the measured lengths. Heights and gap support 0 to 3,000 cm equivalent. Usable wall top and horizontal distances must be at least 0.01 cm equivalent. Screen diagonals support 1 to 300 inches. Aspect components each support 1 to 100. Each user-entered angle limit supports 0° to 45°. Enter plain decimals with up to eight decimal places. The diagram uses independent horizontal and vertical scales.
The results describe display geometry. Compare your entered limits and the visible screen area. Physical installation planning also uses product-specific outer dimensions, mounting offsets, hardware and site conditions.

Worked Example

If you input:

  • Room and seats: Inches. Console 25, gap 3, usable wall top 76, proposed center 51.
  • Seat A: Eye 41 in, distance 96 in, upward limit 12°, downward limit 8°
  • Seat B: Eye 38 in, distance 66 in, upward limit 9°, downward limit 10°
  • Screen sizes: 55 in and 85 in diagonal, both 16:9

Result:

The 55 in screen has a feasible center from 41.4822 to 48.4534 in. The nearest point to the proposed 51 in center is 48.4534 in. The 85 in screen needs a center at or above 48.8361 in to clear the console, while Seat B limits the center to 48.4534 in. Their ranges miss by about 0.38273 in.

Frequently Asked Questions

Is the screen center measured from the floor?

Yes. Measure the console, usable wall top, eye positions and proposed screen center from the same floor reference.

Why can a larger TV require a higher center?

A taller display extends farther below its center. Keeping the same gap above the console raises the display’s minimum center height. It also extends farther above its center, lowering the highest center that clears the usable wall top.

Why is there no feasible center even though the TV fits on the wall?

The room can allow the screen edges while the seats restrict the center height. If the largest required minimum exceeds the smallest allowed maximum, no center satisfies all entered constraints.

What do positive and negative viewing angles mean?

Positive means the center is above a seat’s eye level. Negative means the center is below. At equal heights, the center sightline is horizontal and its angle is zero.

How does the tool pick the closest feasible center?

It keeps your proposed center when all constraints allow it. Otherwise it chooses the closer endpoint of the shared range. The table identifies which constraint controls each endpoint.

Does the diagonal include the bezel or mount?

Use the visible display diagonal and its aspect ratio to calculate the active screen area. Use the product’s outer dimensions and mounting details when planning its physical installation.

Similar Calculators