Torque & Horsepower Curve Calculator

Enter torque measurements at one or more engine speeds to see what power the shaft delivers at the same speeds. Chart mechanical horsepower, kilowatts or torque, inspect an RPM between entered points and export the values. Compare two runs to see which delivers more power at a shared speed and where their estimated curves meet.

RPM and torque

Compare torque and horsepower curves

Turn measured RPM and torque into mechanical horsepower and kilowatts. Compare sampled peaks, inspect a speed, and estimate where the runs meet.

Measured peaks

Run A

Peak sampled power
222.767 hp
166.118 kW at 6,000 RPM
Peak sampled torque
230 lbf·ft
At 4,000 RPM

Sampled RPM range 2,000–7,000

Run B

Peak sampled power
259.895 hp
193.804 kW at 6,500 RPM
Peak sampled torque
225 lbf·ft
At 3,500 RPM

Sampled RPM range 2,500–7,500

Peaks use entered rows. For tied values, the earlier RPM is shown.

Run A peak sampled power 222.767 horsepower. Run B peak sampled power 259.895 horsepower.

Power and torque curves

Dots mark entered RPMs. The lines use linear torque between samples and derive power from that torque.

Power (mechanical hp)

Engine speed (RPM)

  • Run A, solid
  • Run B, dashed
  • Estimated match

Inspect a speed

Enter a covered speed. Clear it to hide the inspection marker.

Run A
209.44 hp · 156.179 kW
298.28 N·m · 220 lbf·ft
Entered speed
Run B
214.199 hp · 159.729 kW
305.059 N·m · 225 lbf·ft
Interpolated torque

Where the runs match

Shared RPM range 2,500–7,000

3,666.67, 4,500 RPM

The estimate finds equal torque within both sampled ranges. At each positive matching RPM the two power values also agree.

Edit measurements

Enter one torque per RPM. To compare runs, use measurements taken at the same point in the drivetrain and under comparable conditions.

Run A measurements

6 of 30 rows

Run B measurements

6 of 30 rows

Show curve data table
Measurements, inspection and matches
ItemRunSpeed (RPM)Torque (N·m)Torque (lbf·ft)Power (hp)Power (kW)Source
MeasurementA2,000244.04718068.543851.1131Sample
MeasurementA3,000291.501215122.80891.5777Sample
MeasurementA4,000311.838230175.168130.622Sample
MeasurementA5,000298.28220209.44156.179Sample
MeasurementA6,000264.384195222.767166.118Sample
MeasurementA7,000210.152155206.584154.049Sample
InspectionA5,000298.28220209.44156.179Sample
MeasurementB2,500291.501215102.3476.3147Sample
MeasurementB3,500305.059225149.94111.81Sample
MeasurementB4,500305.059225192.78143.756Sample
MeasurementB5,500305.059225235.619175.701Sample
MeasurementB6,500284.722210259.895193.804Sample
MeasurementB7,500237.268175249.899186.35Sample
InspectionB5,000305.059225214.199159.729Interpolated
Estimated matchA and B3,666.67305.059225157.08117.134Linear torque model
Estimated matchA and B4,500305.059225192.78143.756Linear torque model

Export curve data

Save the measurements, inspection and modeled matches in both unit systems.

Download curve CSV
Show selectable CSV

At about 5,252.11 RPM, a nonzero torque in lbf·ft and its mechanical horsepower have the same numerical reading.

How to use this calculator

  1. Start with Two illustrative dyno runs or Constant torque example. Use Compare two runs to show a second dataset when you have comparable measurements.
  2. In Edit measurements, choose Torque input unit and enter one torque for each RPM. Add or remove rows as needed. The chart sorts entered measurements by RPM.
  3. Read Measured peaks for the highest sampled torque and power. In Power and torque curves, choose a Chart quantity to see mechanical hp, kW or either torque unit.
  4. Use Inspect at RPM to view the measured or estimated value at a specific speed. In comparison mode, read Where the runs match for estimated matches in the shared sampling range.
  5. Open Show curve data table for the measured and modeled values. Download curve CSV or use its selectable copy to retain both sets of units.

The Formula

The mathematical logic powering this calculation is:

For torque τ in newton-meters and rotational speed n in revolutions per minute, angular speed is ω = 2πn/60 radians per second. Power in watts is P = τω. Divide by 1,000 for kilowatts. In the U.S. customary units used here, one lbf·ft equals 1.3558179483314004 N·m by the standard pound-force and international foot definitions. Mechanical horsepower is exactly 550 ft·lbf/s, equivalent to 745.69987158227022 W. For torque in lbf·ft this gives mechanical hp = τ × RPM × π/16,500.
For inspection between two entered speeds n₁ and n₂, the tool estimates τ(n) = τ₁ + (τ₂ − τ₁)(n − n₁)/(n₂ − n₁) and then computes power at n. That makes torque linear and power generally quadratic between samples. To find equal torque across two runs, the tool solves the linear torque difference over the intervals between both sets of entered speeds, inside their shared range. It reports individual matches and merges consecutive intervals over which their estimated torque agrees. At positive matching RPMs, power values agree as well. At 0 RPM, both power values are zero even if torque differs.
Peaks are based on the greatest entered torque and greatest calculated power at an entered speed. Ties use the lowest RPM. An interpolated curve can reach a higher power between measured speeds, depending on the shape of the torque estimate. The tool does not extrapolate outside either measured range. Compare values from the same shaft or measurement point. The workspace uses the entered data directly, without correction factors or drivetrain-loss estimates.
Enter 1–30 unique speeds per run, from 0 to 100,000 RPM, with up to three decimal places. Each torque can be positive, zero or negative and must fall within ±100,000 N·m equivalent, with up to 12 decimal places. Enter numbers without grouping commas. On a torque-unit switch, the displayed field can round to 12 decimal places while the original quantity is preserved until edited. Displayed results use about six significant digits, and the CSV carries calculation precision.

Worked Example

If you input:

  • Run A measurements: Illustrative RPM/lbf·ft pairs (2,000/180, 3,000/215, 4,000/230, 5,000/220, 6,000/195, 7,000/155)
  • Run B measurements: Illustrative RPM/lbf·ft pairs (2,500/215, 3,500/225, 4,500/225, 5,500/225, 6,500/210, 7,500/175)
  • Compare two runs: Enabled
  • Inspect at RPM: 5,000 RPM

Result:

Run A peaks at 222.767 hp at 6,000 RPM and Run B at 259.895 hp at 6,500 RPM. At 5,000 RPM the entered Run A value gives 209.44 hp and Run B’s interpolated torque gives 214.199 hp. The runs’ torque and power estimates agree at about 3,666.67 RPM and at 4,500 RPM.

Frequently Asked Questions

How do I calculate mechanical horsepower from torque and RPM?

Multiply torque in lbf·ft by RPM and divide by about 5,252.113. At 4,000 RPM, 230 lbf·ft produces about 175.168 mechanical hp. The calculator uses the unrounded conversion and also gives kilowatts.

Why do torque and horsepower show the same number near 5,252 RPM?

Mechanical horsepower is 550 foot-pound-force per second. At 5,252.113122 RPM, the angular speed is 550 radians per second, so mechanical horsepower and torque in lbf·ft show the same number. The numerical equality depends on those units. Torque and power remain different physical quantities.

Why does the curve sometimes rise above the displayed peak?

The peak card uses only entered speeds. Between those speeds the chart estimates torque and multiplies it by angular speed to estimate power. The estimate can briefly exceed both adjacent measured power values. Denser measurements help confirm where the actual peak occurs.

What is an estimated match between two runs?

It is a shared speed at which both interpolated torque values agree. It can be a point where the curves cross, a point where they touch, or a whole matching range. A match at positive RPM also gives the same power for both runs.

Does this convert wheel horsepower to crankshaft horsepower?

Power is computed for the shaft or point where the entered torque and speed were measured. Use comparable measurement points when comparing two runs. This calculation needs the torque and RPM at the point you want to evaluate.

What does negative power mean?

With RPM treated as nonnegative, negative torque opposes the chosen direction of rotation. At positive RPM it yields negative power, which describes mechanical power absorbed from that rotating shaft.

Similar Calculators