French Drain Material & Trench Quote Planner
Measure each straight run once, then compare two trench profiles and supplier quotes. Enter top and bottom trench widths, fill depth and pipe outside diameter to calculate excavated volume, placed gravel and the upper cap. Compare gravel order increments with usable fabric roll dimensions and see how those purchase quantities affect the quote.
Compare French drain materials and quotes
Check your measured trench, calculate placed gravel and whole fabric rolls, and compare two quotes across the same runs.
The example uses illustrative dimensions and prices. Enter measured sections and supplier quotes for your project.
Option A
$1,963.00
Complete quote for entered scope
- Placed gravel
- 3.1394 yd³
- Ordered gravel
- 3.5 yd³
- Whole fabric rolls
- 1
Option B
$2,602.00
Complete quote for entered scope
- Placed gravel
- 5.3616 yd³
- Ordered gravel
- 6 yd³
- Whole fabric rolls
- 2
Option A is $639.00 lower for the measured route.
Complete quote for Option A. Complete quote for Option B. Option A is $639.00 lower for the measured route.
Measured trench cross-sections
Both drawings use the same scale. The thin clearance line follows the shortest path from the pipe to a trench side.
- Upper cap
- Gravel
- Pipe envelope
- Fabric trace
- Trench depth
- 18 in
- Gravel height
- 12 in
- Bottom width
- 18 in
- Top width
- 18 in
- Side clearance
- 7 in clear
- Above the pipe
- 6 in clear
Pipe is inside the entered gravel section.
Closed wrap needs 66 in of usable width.
- Trench depth
- 30 in
- Gravel height
- 20 in
- Bottom width
- 14 in
- Top width
- 26 in
- Side clearance
- 5.8446 in clear
- Above the pipe
- 13 in clear
Pipe is inside the entered gravel section.
Closed wrap needs 82.7922 in of usable width.
Fabric roll cut plan
Each run needs one continuous cut. Pieces share a roll lengthwise. The plan treats the remaining strip across a cut's width as an offcut.
Option A fabric
Width fits. 66 in needed, 72 in available. 6 in crosswise offcut.
Roll 1 · 60 of 60 ft
Side yard 40 ft · Back yard 20 ft
0 ft remains after cuts.
Option B fabric
Width fits. 82.7922 in needed, 84 in available. 1.2078 in crosswise offcut.
Roll 1 · 40 of 50 ft
Side yard 40 ft
10 ft remains after cuts.
Roll 2 · 20 of 50 ft
Back yard 20 ft
30 ft remains after cuts.
Measured route
Both options use these runs. Measure each straight run along the route. Enter the total extra length at both ends of a fabric cut.
60 ft total measured length
Edit Option A inputs
Edit Option B inputs
Show quantities and quote ledger
The excavated trench equals placed gravel, the pipe envelope and the upper cap. Purchased gravel includes additional material and order increments.
| Quantity or cost | Option A | Option B |
|---|---|---|
| Excavated trench | 5 yd³ | 9.2593 yd³ |
| Net placed gravel | 3.1394 yd³ | 5.3616 yd³ |
| Pipe envelope | 0.1939 yd³ | 0.1939 yd³ |
| Upper cap | 1.6667 yd³ | 3.7037 yd³ |
| Gravel plus allowance | 3.4533 yd³ | 5.8978 yd³ |
| Purchased gravel | 3.5 yd³ | 6 yd³ |
| Ordered gravel | $245.00 | $390.00 |
| Measured pipe | $240.00 | $240.00 |
| Whole fabric rolls | $78.00 | $172.00 |
| Excavation | $500.00 | $700.00 |
| Installation | $800.00 | $950.00 |
| Other quoted costs | $100.00 | $150.00 |
| Complete quote | $1,963.00 | $2,602.00 |
Option A measured by run
- Side yard · 40 ft
- 3.3333 yd³ excavated · 2.0929 yd³ placed gravel · 0.1293 yd³ pipe envelope · 1.1111 yd³ upper cap
- Back yard · 20 ft
- 1.6667 yd³ excavated · 1.0465 yd³ placed gravel · 0.0646 yd³ pipe envelope · 0.5556 yd³ upper cap
Option B measured by run
- Side yard · 40 ft
- 6.1728 yd³ excavated · 3.5744 yd³ placed gravel · 0.1293 yd³ pipe envelope · 2.4691 yd³ upper cap
- Back yard · 20 ft
- 3.0864 yd³ excavated · 1.7872 yd³ placed gravel · 0.0646 yd³ pipe envelope · 1.2346 yd³ upper cap
Export results
Show selectable CSV text
How to use this calculator
- Enter the measured length of each straight run. Add any longitudinal fabric allowance required at its ends.
- Enter bottom width, top width, full trench depth and the height filled with gravel. Measure the pipe's outside diameter, bedding and any offset.
- Choose an open U liner or a closed wrap. Enter usable roll dimensions and the gap allowed between consecutive cuts.
- Enter the aggregate order increment and both proposals' prices. Enter zero on a line when it is included elsewhere.
- Check the cross-sections, whole-roll assignments and cost ledger. Export the complete comparison and cut plan as CSV.
The Formula
The mathematical logic powering this calculation is:
The route has one to eight measured, nonoverlapping straight runs. Each option uses one symmetric cross-section across that route. Set b to bottom width, t to top width, H to full depth and h to the gravel height from the bottom. The gravel-top width is w = b + (t − b)h/H. Excavated area is (b + t)H/2 and the gravel envelope area is (b + w)h/2. Subtract πD²/4 for the circular envelope of the pipe's outside diameter D. The cap above the gravel is the area between those two trapezoids. Multiply each area by measured run length in inches and divide by 46,656 for cubic yards. Excavated volume equals net placed gravel, the pipe envelope and the upper cap.
Pipe bedding e is the vertical distance below the pipe's exterior. Its top is at e + D and its center is at e + D/2. At the center, the nearest side's perpendicular distance is [b/2 + k(e + D/2) − |x|] ÷ √(1 + k²), where k = (t − b)/(2H) and x is the pipe offset. The circle fits inside the entered gravel when its top is at or below h and its nearest side distance is at least D/2. The exact boundary represents contact. Equivalent squared inequalities in fixed decimal units control acceptance at the boundaries.
An open U liner follows the bottom and two stone-side lengths, b + 2√[h² + ((w − b)/2)²]. A closed wrap adds w and the entered crosswise lap. A continuous cut for each run adds the entered end allowance to measured length. The fabric stock calculation requires usable width at least as large as cut width, then finds the fewest whole rolls with the entered length and cut gap. Cuts share a roll lengthwise and the remaining width within a cut is an offcut. Each cut stays in one piece.
Apply the entered gravel percentage to placed gravel and round the total up once to the supplier increment. Enter 0 for a continuous purchase. Aggregate and pipe lines use the entered rates per cubic yard and foot. Fabric uses the entered price for each whole roll. Each line rounds to USD cents with halfway values rounded upward. Excavation, installation and other amounts come from the entered quotes. The cost comparison appears when both quotes are complete.
Enter dimensions, percentages and order increments to three decimals and USD rates or amounts to two. Route segments run from 0.001 to 2,000 ft each with up to 100 ft of fabric end allowance. Trench dimensions run from 0.001 to 240 in, pipe diameter to 120 in, roll width to 1,200 in and roll length to 4,000 ft. Extra gravel permits 0–100%, and the supplier increment 0–100 yd³. The model covers measured geometry, continuous liner cuts and quoted costs. Allow separately for corners, junctions, excavation beyond the measured section, and project-specific drainage and safety requirements.Worked Example
If you input:
- Measured route: 40 ft side yard and 20 ft back yard
- Option A profile: 18 in bottom and top width, 18 in deep with 12 in of gravel and a 4 in OD pipe
- Option B profile: 14 in bottom and 26 in top width, 30 in deep with 20 in of gravel and a 4 in OD pipe
- Fabric and gravel purchase: 6 in lap, 72 in × 60 ft stock for A and 84 in × 50 ft stock for B. Enter 10% extra gravel in 0.5 yd³ increments.
- Option A prices: $70 per yd³ gravel, $4 per ft pipe, $78 per roll, $500 excavation, $800 installation, $100 other
- Option B prices: $65 per yd³ gravel, $4 per ft pipe, $86 per roll, $700 excavation, $950 installation, $150 other
Result:
Option A places about 3.1394 yd³ of gravel and buys 3.5 yd³ plus one fabric roll for a $1,963 complete quote. Option B places about 5.3616 yd³ and buys 6 yd³ plus two rolls for $2,602. The modeled price difference is $639 for that measured route.
Frequently Asked Questions
How much gravel goes in a French drain trench?
Use the area of the filled portion at its measured widths and height, then subtract the circular pipe envelope. Multiply by the measured length. The placed quantity differs from what you purchase after adding allowance and a supplier increment.
Should I enter the nominal or outside pipe diameter?
Enter outside diameter. It measures the envelope that displaces gravel and determines whether the modeled circle fits. A trade size printed on the pipe may describe a different dimension.
Why can a pipe intersect a tapered wall even if the width seems large enough?
The closest wall is reached along a perpendicular from the pipe's center. That shortest distance can be smaller than the horizontal space shown at the same height. The worksheet marks the actual signed side clearance.
What fabric dimensions should I compare?
Use the supplier's usable width and length. A closed wrap includes the top width and your crosswise lap. Each continuous cut also needs the full measured run length and its longitudinal end allowance.
Why does square footage underestimate the whole roll count?
Each cut must pass width and length separately, and pieces share a roll lengthwise. Three 40 ft pieces each fit a 60 ft roll, but two pieces cannot share one. Three rolls are needed under this cut plan.
How do I show that a contractor included an item at no extra cost?
Enter zero on that line. A blank price keeps the complete quote pending so it cannot be mistaken for included work. Use Other quoted costs for entered items such as haul-away or delivery.
Does this calculate slope or drainage performance?
Use dimensions from the measured design or proposal. The model estimates materials and entered costs; drainage capacity, grades, outlets, trench protection and project suitability require separate evaluation.
Similar Calculators
Gravel & Crushed Stone Calculator
Estimate gravel and crushed stone for multiple sections. Compare bulk tons or yards with whole bags, including density, compaction, allowance and cost.
Sewer Replacement Cost & Surface Planner
Compare sewer replacement costs across pipe work, access patches and surface restoration. Visualize cost ranges, footprints, budget headroom and price crossovers.
Drainage Pipe Slope & Gravity Flow Calculator
Compare drainage pipe diameters, slope, flow depth and required fall. Explore Manning capacity curves, near-full depth branches, pipe sections and complete CSV data.
