Bicycle Size Calculator & Cockpit Fit Comparison

Compare the front-end dimensions of two bicycle frames against a handlebar clamp position you already know or want to reproduce. Enter frame stack and reach, the head-tube angle and the stem geometry. View both clamp positions and their signed differences in millimeters. See whether a change within the entered steerer range reaches the target height, how far forward or back the resulting clamp sits, and the separate standover measurement if entered.

Bicycle geometry worksheet

Compare bicycle frames at your clamp position

Compare two entered frame and stem setups against a clamp position measured relative to the bottom bracket.

Only Frame A is within both current clamp tolerances.

Frame A differences from target
−0.608 mm forward · −2.23 mm up
Height matches at 32.332 mm of offset. Forward difference −1.29 mm (within tolerance).
Frame B differences from target
+3.327 mm forward · −6.571 mm up
Height matches at 26.909 mm of offset. Forward difference +1.191 mm (within tolerance).
Handlebar clamp target

Measure the desired clamp center forward and up from the bottom bracket. Positive differences land farther forward or higher.

Clearance is inseam minus standover at the chart's specified point.

Frame A

Center to center.

At a 73° head angle, −17° produces a level stem.

Along the steerer, from the top head-tube reference to the stem clamp center.

Frame B

Center to center.

At a 73° head angle, −17° produces a level stem.

Along the steerer, from the top head-tube reference to the stem clamp center.

Standover comparison

Measured inseam minus the published height at its stated measurement point.

Frame A
+20 mm
Frame B
−5 mm
Cockpit and target geometry

The view uses the same scale in both directions. Coordinates are relative to the bottom bracket.

Handlebar clamp positions and tolerance windowShared-scale head-tube, stem, and clamp positions. Target 470 mm forward by 610 mm up. Frame A differences −0.608 mm forward, −2.23 mm up. Frame B differences +3.327 mm forward, −6.571 mm up.Forward (mm)Up (mm)
Frame AFrame BTarget and tolerance window

Filled points are current clamps. Open points reach the target height. Dotted lines show each entered adjustment range.

Clamp coordinates and fit ledger

Target clamp 470 mm forward and 610 mm up. Allowed differences ±6 mm forward and ±6 mm up.

Current cockpit dimensions and modeled height match
MeasurementFrame AFrame B
Frame head-tube center380 mm forward · 560 mm up390 mm forward · 575 mm up
Stem pivot center371.229 mm forward · 588.689 mm up383.82 mm forward · 594.021 mm up
Current bar clamp469.392 mm forward · 607.77 mm up473.327 mm forward · 603.429 mm up
Forward difference−0.608 mm+3.327 mm
Height difference−2.23 mm−6.571 mm
Ground stem angle11°6°
Current steerer offset30 mm20 mm
Clamp height range588.644 mm to 636.459 mm593.918 mm to 641.471 mm
Required offset for target height32.332 mm26.909 mm
Forward difference at target height−1.29 mm+1.191 mm
Published standover780 mm805 mm
Inseam minus standover+20 mm−5 mm
Download cockpit comparison CSV
Show selectable CSV

How to use this calculator

  1. Enter the center of the desired handlebar clamp measured forward and up from the bottom bracket. Set independent tolerances for both dimensions.
  2. For each frame, enter published reach, stack and head angle, then enter the center-to-center stem length and choose the angle convention.
  3. Enter the distance along the steerer to the stem clamp center and the allowable minimum and maximum for that setup.
  4. Compare current signed differences and the continuous height-match result. Switch the plot to inspect the tolerance window and each clamp path.
  5. Optionally compare inseam with published standover recorded at the same reference location. Review the ledger and download the comparison.

The Formula

The mathematical logic powering this calculation is:

Use the center of the bottom bracket as the origin. Forward x is horizontal and up y is vertical. Reach R and stack S locate the top-center head-tube reference at (R, S). The head angle h is measured from the ground. A distance d up the steerer has horizontal component −d cos h and vertical component d sin h. Measure d from the head-tube reference to the center of the stem’s steerer clamp, including the appropriate cover, spacers and part of the clamp height.

A stem of center-to-center length L and ground slope θ adds (L cos θ, L sin θ). Use θ directly when measured from horizontal. If the rise α is signed from perpendicular to the steerer, θ = 90° − h + α. This convention gives a level stem for h = 73° and α = −17°. The clamp is therefore (R − d cos h + L cos θ, S + d sin h + L sin θ).

Subtract the target coordinates from the clamp coordinates to get signed differences. Both absolute differences must be within their respective entered tolerances for a current match. To match the exact target height Y with the same stem, solve d = (Y − S − L sin θ)/sin h. When d lies in the entered range, compare the implied forward coordinate with the separate horizontal tolerance. The range is continuous geometry from user-entered limits. The worksheet does not check available components or discrete spacer sizes. Comparison boundaries include 10⁻⁹ mm to absorb rounding.

The optional clearance is measured inseam minus published standover at the stated location. It is a separate comparison. Frame charts use different standover locations, and actual measures depend on the setup. The worksheet models the center of the handlebar clamp. It does not model saddle position, reach to the grips or hoods, handling or rider comfort.

Millimeter and degree inputs support up to two decimals. Frame stack accepts 100 to 1,200 mm, reach 50 to 1,000 mm, and head angle 45 to 90°. Stem length accepts 10 to 250 mm, steerer offsets 0 to 200 mm, and rise −45 to +45° from perpendicular to the steerer or −45 to +90° from horizontal. Target forward is 0 to 1,500 mm, target up is 100 to 1,700 mm, and each tolerance is 0 to 250 mm. The optional heights accept 400 to 1,400 mm.

Worked Example

If you input:

  • Target handlebar clamp: 470 mm forward, 610 mm up, ±6 mm on each axis
  • Frame A stack, reach, head angle: 560 mm, 380 mm, 73°
  • Frame B stack, reach, head angle: 575 mm, 390 mm, 72°
  • Stem and offset A: 100 mm stem, −6° from steerer perpendicular, 30 mm current offset
  • Stem and offset B: 90 mm stem, −12° from steerer perpendicular, 20 mm current offset

Result:

Frame A currently lands 0.608 mm behind and 2.230 mm below the target, within both tolerances. Frame B lands 3.327 mm forward and 6.571 mm low. An offset of approximately 26.909 mm for B reaches the target height with 1.191 mm of forward difference.

Frequently Asked Questions

What is the difference between frame reach and handlebar reach?

Frame reach ends at the top-center head-tube reference. This comparison adds the steerer offset and stem to reach the bar clamp center. Grips and hoods can sit elsewhere depending on bar shape and how it is set up.

Where do I measure the steerer offset?

Measure along the steering axis from the chart’s head-tube reference to the center of the stem’s steerer clamp. A spacer stack by itself typically omits the cover and part of the clamp.

Why does raising the clamp usually move it back?

An angled steerer points rearward as it rises. A horizontal component accompanies the vertical change. A vertical steerer has no such horizontal change.

How do I enter a stem marked 73° or ±17°?

Confirm the maker’s angle reference before entering it. When the maker supplies signed rise from perpendicular to the steerer, use the signed setting. When you measure the stem from horizontal on the bicycle, enter that ground angle directly.

Can equal clamp positions determine the best bike size?

They show one way the front ends compare. Saddle position, ride geometry, grips, clearances and your own measurements also matter. This tool compares entered dimensions and tolerances without selecting a frame size.

Similar Calculators