Run Walk Pace Calculator & Race Plan

Use this run walk pace calculator to compare an entered race plan and the run pace needed for a finish target. Enter a course distance, two paces and the length of each interval. The planner starts with a run, repeats the intervals and ends the clock exactly at your course distance. Compare both paths on the chart, and check the timing at each kilometre or mile.

Plan timed run and walk intervals

See your finish with the paces you enter, including the last partial interval. Compare the run pace needed for the same schedule at your target time.

Course, intervals and target

km

h:mm:ss or m:ss

m:ss

m:ss

m:ss per km

m:ss per km

The clock starts with a run. The schedule repeats at the two steady paces until the course ends.

Finish and target pace

Entered plan finishes in 2:17:23.1. 12:36.9 under target.
Entered plan finish
2:17:23.1
12:36.9 under target
Run pace for target
6:37.8 per km
Keep the same walk pace and intervals.
Overall pace
6:30.7 per km
Finish target
2:30:00

Distance over elapsed time

Entered planRun pace for targetTarget deadline

Course covered (km)

Run and walk distance over timeThe entered plan covers 21.0975 km in 2:17:23.1. Target deadline 2:30:00. 12:36.9 under target.

Elapsed time

Steeper sections cover distance faster. The overview samples long interval schedules. Each split and the final segment use the exact phase timing below.

Run and walk time to the finish

Entered plan

Time running
1:50:23.1
18.3975 km
Time walking
27:00
2.7 km

Run in cycle 28 · 2:23.1 of 4:00

Run pace for target

Time running
2:00:00
18.0975 km
Time walking
30:00
3 km

Walk in cycle 30 · full 1:00 interval

Course split ledger

A checkpoint every kilometre, plus the actual finish. The last split can be shorter.

Open checkpoint splits
Checkpoint (km)Split (km)Entered splitEntered elapsedTarget splitTarget elapsed
116:246:246:58.16:58.1
216:2412:486:58.113:56.1
316:3219:207:18.321:14.4
416:4026:006:58.128:12.5
516:2432:247:18.335:30.7
616:2438:486:58.142:28.8
716:4845:367:11.749:40.5
816:2452:007:04.656:45.1
916:2458:246:58.11:03:43.2
1016:481:05:127:18.31:11:01.5
1116:241:11:366:58.11:17:59.5
1216:241:18:007:18.31:25:17.8
1316:401:24:406:58.11:32:15.9
1416:321:31:127:05.11:39:21
1516:241:37:367:11.21:46:32.2
1616:241:44:006:58.11:53:30.3
1716:481:50:487:18.32:00:48.5
1816:241:57:126:58.12:07:46.6
1916:242:03:367:18.32:15:04.9
2016:482:10:246:58.12:22:02.9
2116:242:16:486:58.62:29:01.5
21.0975 · Finish0.09750:35.12:17:23.10:58.52:30:00
Show selectable CSV

How to use this calculator

  1. Choose kilometres or miles and enter the course distance.
  2. Enter the length of one run and one walk, then enter the pace for each phase. Use a time such as 6:00 per kilometre.
  3. Set a finish target. Compare the modeled finish and the run pace that would reach your target with the same intervals and walk pace.
  4. Inspect the last run or walk and the course splits. Export the plan to retain the assumptions, exact splits and plotted points.

The Formula

The mathematical logic powering this calculation is:

Use seconds and kilometres in the timing model. Within a phase, distance = phase seconds ÷ phase pace in seconds per kilometre. One cycle covers the run distance plus the walk distance. Subtract complete cycles from the course, then use the remaining distance in the final run or walk. If you finish exactly at a phase boundary, that full phase is the finish interval. Overall pace = elapsed seconds ÷ course distance.

For the target, compute the run seconds and walk seconds scheduled before the selected deadline. Required run pace = scheduled run seconds ÷ (course distance − distance covered in the scheduled walk time). This keeps the walk pace and both timed intervals fixed. If the scheduled walk time alone can cover the distance by the deadline, any positive run speed in this model finishes before it. There is no finite run pace for that exact finish. A mathematically possible pace outside the supported range has no target-path output.

The examples use measured road distances of 5 km and 21.0975 km. A mile equals 1,609.344 metres. Change units without changing the physical quantities you have entered. Split resolution follows your selected units. Finish and split displays round to tenths of a second, while calculations and CSV use the modeled precision.

Use courses from 10 m to 200 km, intervals from one second to one hour, paces from 0:30 to 30:00 per kilometre or equivalent per mile, and a finish target from one second to seven days. This deterministic comparison assumes steady pace in each phase and instant transitions. Course grade, stops, fatigue, crowds and unexpected delays are outside the model.

Worked Example

If you input:

  • Course distance: 21.0975 km (half marathon)
  • Run and walk intervals: 4:00 run · 1:00 walk
  • Run pace and walk pace: 6:00 per km · 10:00 per km
  • Finish target: 2:30:00

Result:

The entered plan finishes in 2:17:23.1, which is 12:36.9 under target. After 27 full cycles, 397.5 m remain. You finish after 2:23.1 of the next run. A run pace of about 6:37.8 per km reaches the 2:30:00 target with the same walk pace and intervals.

Frequently Asked Questions

How do I calculate the average pace when alternating running and walking?

Divide total elapsed time by total distance. The arithmetic mean of your two pace settings ignores the time spent in each phase and the partial interval at the finish.

Do I need to finish the final timed interval?

The model stops at your course distance. The last segment can use only part of a run or walk. If the course ends at an interval boundary, the model records the completed interval.

Why does the target plan change only run pace?

Holding the walk pace and both interval lengths fixed gives a single unknown to solve. Edit the other fields to compare a different schedule.

What if the calculated run pace is slower than my walk pace?

For some finish targets the assigned run time would need to cover less distance per minute than the walk time. The workspace flags the relationship as part of the arithmetic comparison.

Do miles change the projection?

Switching units keeps course length and both paces physically equivalent. The checkpoint table changes from kilometre splits to mile splits, with an exact last checkpoint in both cases.

Does this forecast my race result?

It compares schedules with the steady paces and instant transitions you enter. Allow separately for changes in effort, terrain, stops and start timing.

Similar Calculators