Pitching Speed Calculator & Video Timing
Measure two pitch flights or compare two recordings of the same pitch. Enter the actual distance between your marked events and the recorded capture frame rate, or use an elapsed time and its tolerance. The calculator shows the measurement limits implied by your inputs, whether the two speed ranges overlap, and the lowest whole frame rate that would meet your target interval width under the same nominal flight time and distance.
Compare two measured pitch speeds
Use frame marks or elapsed time to compare average speed and see how far timing uncertainty can shift the result.
Clip A measurement
Use the recorded capture rate. Fractions such as 30000/1001 are accepted.
Mark the first frame at or after each event. Use the same two points to measure distance.
Clip B measurement
Use the recorded capture rate. Fractions such as 30000/1001 are accepted.
Mark the first frame at or after each event. Use the same two points to measure distance.
Frame-rate target
Clip A is faster across the entered bounds.
Axis in mph. Circles show nominal speeds. An arrow indicates no finite upper bound.
Capture rate for the target width
- Blue line · modeled width
- Dotted line · target width
- Dashed line · distance only
Horizontal axis in fps. Vertical axis in mph of full interval width. The chart holds distance and nominal elapsed time fixed.
Open frame-rate probes
| Capture fps | Speed width (mph) |
|---|---|
| 15 | 33.311688 |
| 24 | 21.109737 |
| 30 | 17.164654 |
| 48 | 11.32333 |
| 60 | 9.391304 |
| 90 | 6.823447 |
| 120 | 5.542178 |
| 150 | 4.774053 |
| 180 | 4.262186 |
| 240 | 3.622552 |
| 300 | 3.238861 |
| 355 | 3.001109 |
| 356 | 2.997467 |
| 480 | 2.663425 |
| 600 | 2.471634 |
| 960 | 2.183964 |
| 1,200 | 2.088077 |
| 1,920 | 1.94425 |
| 2,400 | 1.896309 |
| 3,840 | 1.824397 |
| 4,800 | 1.800427 |
| 7,500 | 1.765909 |
| 10,000 | 1.750568 |
Timing and speed worksheet
| Measurement | Lower | Nominal | Upper |
|---|---|---|---|
| Clip A distance (m) | 16.3068 | 16.4592 | 16.6116 |
| Clip A elapsed (s) | 0.391667 | 0.4 | 0.408333 |
| Clip A average speed (mph) | 89.332096 | 92.045455 | 94.874275 |
| Clip B distance (m) | 16.4592 | 16.4592 | 16.4592 |
| Clip B elapsed (s) | 0.429167 | 0.433333 | 0.4375 |
| Clip B average speed (mph) | 84.155844 | 84.965035 | 85.789938 |
Show selectable CSV
How to use this calculator
- Choose the distance unit and enter the distance between the two locations you will time. Enter zero tolerance only when you are intentionally treating the distance as exact.
- In Frame marks, enter the recorded capture rate and the first recorded frame at or after each event. For trusted external timing, choose Elapsed time and enter the time and its tolerance.
- Repeat for Clip B. Compare the nominal speeds and entered bounds. Keep the two sets of timing marks and distance measurements paired.
- Choose the reference clip, your desired full speed width and a speed unit. Compare the minimum passing capture rate, neighboring frame rates and the limit imposed by distance tolerance.
- Open the timing worksheet or download its CSV to review the inputs, exact fractions and frame-rate probes.
The Formula
The mathematical logic powering this calculation is:
Average speed is distance ÷ elapsed time. Measure the distance between the same two event locations used to mark the video. MLB Statcast publishes a separate out-of-hand velocity measurement. Release extension and camera framing can change the length of your measured segment.
For constant capture rate F and N frames between marks, the nominal time is N/F. Mark the first recorded frame at or after each event. Each event can fall between its marked frame and the preceding frame. Elapsed time can therefore range from max(0, N−1)/F to (N+1)/F. With directly entered time, use the entered time plus and minus its tolerance and clamp the lower limit to zero.
Use the shortest possible distance divided by the longest time for the lower speed. Use the longest distance divided by the shortest time for the upper speed. At a zero lower time, the upper speed is unbounded. Equal frame marks also leave the nominal speed unavailable. Strictly disjoint intervals establish an order within the entered bounds. A shared endpoint counts as overlap. These bounds are deterministic and describe the entered measurement ranges.
For capture planning, hold nominal time t and distance limits L and H fixed. The modeled full speed width in metres per second is H/(t−1/F) − L/(t+1/F) when t > 1/F. The width decreases toward (H−L)/t as F increases. The minimum supported integer frame rate is the first from 1 to 10,000 fps whose full width meets the target. A target at or below the distance-only width is unreachable at finite frame rates. The chart shows a range of rates near the decision and the probe table exposes every sampled rate.
Use recorded constant frame rate for frame counting. With variable-rate video, use elapsed time measured from trustworthy timestamps and enter the event-time tolerance separately. Nominal distance is limited to the equivalent of 1,000 m, with a positive lower distance after tolerance. Frame marks can be up to 30 nominal seconds apart. For direct timing enter 0.001–30 seconds, with a tolerance of up to 30 seconds.Worked Example
If you input:
- Clip A: 54 ft ±0.5 ft, 120 fps, frame marks 42 and 90
- Clip B: 54 ft with zero tolerance, 240 fps, frame marks 100 and 204
- Capture planning: Clip A, 3 mph desired full width
Result:
Clip A's 48-frame separation gives a nominal 0.4 s and an average estimate of 92.045 mph. Its bounds are 89.332–94.874 mph. Clip B's 104-frame separation gives 84.965 mph with bounds of 84.156–85.79 mph, so Clip A is faster across the entered bounds. At 355 fps, Clip A's modeled width is 3.001109 mph. At 356 fps it falls to 2.997467 mph, meeting the 3 mph target for the first time.
Frequently Asked Questions
What distance should I use to estimate pitch speed?
Use the measured distance between the two events marked in the footage. If you mark ball release and a catch, measure between those locations. Release extension can shorten the segment compared with the full rubber-to-plate distance.
Which frame rate do I enter for slow-motion footage?
Use the original constant capture rate. A clip recorded at 240 fps can play back at 30 fps. Use 240 fps if your marks count the original recorded frames. With variable frame rate or interpolated frames, use a trustworthy elapsed time and an entered timing tolerance.
Why can a pitch have no finite upper speed bound?
If your timing limits allow zero elapsed time, arbitrarily short positive times remain possible within those bounds. Same-frame marks also remove the nominal time. More frame separation or a better timestamp bracket gives a positive lower time limit.
Why can a narrower target remain out of reach at higher frame rates?
The timing contribution shrinks as capture rate rises. The entered distance range still contributes a full speed width of (longest distance − shortest distance) ÷ nominal time. A tighter distance measurement reduces that limiting width.
Similar Calculators
Uncertainty Propagation Calculator
Propagate independent measurement uncertainties through sums, products and ratios. Compare contributions, expanded uncertainty and input improvement scenarios.
Unit Converter
Convert between units of length, weight, volume, and area — all in one tool.
Bowling Score Calculator
Score ten-pin bowling frame by frame. See strike and spare bonuses, possible final scores, and how the next legal roll affects your target.
