Guitar & Bass String Tension Calculator

Compare two guitar or bass setups string by string. Choose a published D’Addario archive weight or enter a string’s measured weight per unit length. Use the same scale length across a setup or measure individual vibrating lengths for multiscale instruments. The chart shows where tension changes between open notes, and the ledger gives the unit weight needed to match the other setup or a target you choose.

Tuning and string balance

Compare guitar and bass string tension

See what changes with a new tuning, scale length or string construction. Match another setup by unit weight or compare against your own tension target.

Tension and balance

Setup A · 6 strings

103.50 lbf

Mean
17.25 lbf
High to low spread
4.15 lbf

Setup B · 6 strings

99.90 lbf

Mean
16.65 lbf
High to low spread
5.65 lbf

Setup B total change −3.60 lbf (−3.48%)

Edit string setups

Enter strings in the order you want them compared. Positions with only one string remain in that setup’s total.

Used by strings without a measured length.

Used when you enter an open note.

String 1

0.00002215 lb/in in the D’Addario archive

Pitch, string source and scale for string 1
String 2

0.00003744 lb/in in the D’Addario archive

Pitch, string source and scale for string 2
String 3

0.00006402 lb/in in the D’Addario archive

Pitch, string source and scale for string 3
String 4

0.00012671 lb/in in the D’Addario archive

Pitch, string source and scale for string 4
String 5

0.00023964 lb/in in the D’Addario archive

Pitch, string source and scale for string 5
String 6

0.00038216 lb/in in the D’Addario archive

Pitch, string source and scale for string 6

Open-string tension by position

Solid bars show Setup A. Striped bars show Setup B. A vertical marker shows each available target.

  • String 1

    B minus A 0.00 lbf

    Setup A · E416.20 lbf

    Setup B · E416.20 lbf

    Target 16.20 lbf

  • String 2

    B minus A 0.00 lbf

    Setup A · B315.37 lbf

    Setup B · B315.37 lbf

    Target 15.37 lbf

  • String 3

    B minus A 0.00 lbf

    Setup A · G316.55 lbf

    Setup B · G316.55 lbf

    Target 16.55 lbf

  • String 4

    B minus A 0.00 lbf

    Setup A · D318.39 lbf

    Setup B · D318.39 lbf

    Target 18.39 lbf

  • String 5

    B minus A 0.00 lbf

    Setup A · A219.52 lbf

    Setup B · A219.52 lbf

    Target 19.52 lbf

  • String 6

    B minus A −3.60 lbf

    Setup A · E217.47 lbf

    Setup B · D213.87 lbf

    Target 17.47 lbf

String detail and target unit weights

Target unit weight uses that string’s entered pitch and vibrating length. Each paired string in Setup B targets the force at the same position in Setup A.

Show string ledger
Modeled tension by paired position and target unit weight
StringSetup ASetup BTarget information
1

E4 · 16.20 lbf

PL010 · 25.5 in

329.628 Hz · 0.00002215 lb/in

E4 · 16.20 lbf

PL010 · 25.5 in

329.628 Hz · 0.00002215 lb/in

Setup B · 0.00002215 lb/in

0.00 lbf from 16.20 lbf target

2

B3 · 15.37 lbf

PL013 · 25.5 in

246.942 Hz · 0.00003744 lb/in

B3 · 15.37 lbf

PL013 · 25.5 in

246.942 Hz · 0.00003744 lb/in

Setup B · 0.00003744 lb/in

0.00 lbf from 15.37 lbf target

3

G3 · 16.55 lbf

PL017 · 25.5 in

195.998 Hz · 0.00006402 lb/in

G3 · 16.55 lbf

PL017 · 25.5 in

195.998 Hz · 0.00006402 lb/in

Setup B · 0.00006402 lb/in

0.00 lbf from 16.55 lbf target

4

D3 · 18.39 lbf

NW026 · 25.5 in

146.832 Hz · 0.00012671 lb/in

D3 · 18.39 lbf

NW026 · 25.5 in

146.832 Hz · 0.00012671 lb/in

Setup B · 0.00012671 lb/in

0.00 lbf from 18.39 lbf target

5

A2 · 19.52 lbf

NW036 · 25.5 in

110 Hz · 0.00023964 lb/in

A2 · 19.52 lbf

NW036 · 25.5 in

110 Hz · 0.00023964 lb/in

Setup B · 0.00023964 lb/in

0.00 lbf from 19.52 lbf target

6

E2 · 17.47 lbf

NW046 · 25.5 in

82.407 Hz · 0.00038216 lb/in

D2 · 13.87 lbf

NW046 · 25.5 in

73.416 Hz · 0.00038216 lb/in

Setup B · 0.000481491428 lb/in

−3.60 lbf from 17.47 lbf target

Export the tension comparison

Save the string inputs, calculated forces and target unit weights.

Download string tension CSV
Show selectable CSV

How to use this calculator

  1. Choose Guitar · Standard vs Drop D or Bass · Single vs multiscale. Use Setup A and Setup B to edit each configuration and enter strings in corresponding order.
  2. Enter a default scale length and A4 pitch for each setup, then enter each open note and select the matching catalog string.
  3. Open Pitch, string source and scale on a row to use measured frequency, measured unit weight or a measured length for that string.
  4. Set Force display and Tension target. Compare the totals and high to low spread, then read the paired bars and open Show string ledger for the corresponding unit weights.
  5. Download string tension CSV to save both setups and their modeled forces, pitch, scale length and target values.

The Formula

The mathematical logic powering this calculation is:

For unit weight UW in pounds per linear inch, vibrating length L in inches and fundamental frequency F in hertz, the D’Addario model gives tension T = UW × (2LF)²/386.4 in pound-force. The constant follows the publisher’s customary formula. Multiply pound-force by 4.4482216152605 to display newtons. The measured g/m entry converts to lb/in by multiplying it by 0.0254/453.59237. A catalog selection retrieves the stored unit weight by its product code. Different constructions can have different unit weights at the same nominal gauge.
For twelve-tone equal temperament, F = A4 × 2^(n/12), where n is the signed number of semitones from A4 to the entered open note. For example, E4 is five semitones below A4 and 440 Hz gives approximately 329.628 Hz. The octave number changes at C. Sharp and flat spellings that represent the same pitch produce the same frequency. A measured open frequency uses the entered hertz directly.
Setup total is the sum of string tensions. Mean divides that total by the number of strings. Balance spread is the highest tension minus the lowest. Paired rows use the same position in each setup. A string with no counterpart contributes to its setup’s total and has no paired difference. The report shows B minus A and computes percent change relative to A. Compare per-string results or the mean when string counts differ.
For a target force T, required unit weight = T × 386.4/(2LF)². Match mode uses the tension at the same position in Setup A as the target for Setup B. Fixed mode uses your entered target for every string in both setups. The difference from target is modeled force minus target force. The result is a unit weight for the entered pitch and length. Compare it with the published or measured weights of the strings you are considering.
Enter 1–12 strings per setup. Shared and per-string scale lengths support 12–48 in with up to four decimal places. A4 supports 380–480 Hz with four decimal places. Notes from C0 through B8 accept single sharps or flats, including the equivalent labelling across octave boundaries. Measured frequencies support 10–10,000 Hz with six decimal places. Positive measured weights support 0.000001–0.01 lb/in or 0.017857967323–178.579673228346 g/m with twelve decimal places. Switching a measured input’s display unit preserves its existing quantity until you edit it. Fixed targets support 0.1–500 lbf with four decimal places. The CSV includes both force units and the original weight entry.
The formula treats the string as flexible and uniformly dense over its vibrating length. Actual stiffness, winding variations and contact geometry can affect measurements. The published weights are from the historical catalog; current strings may differ. The setup total represents the modeled tensions of the individual strings.

Worked Example

If you input:

  • Scale and pitch: 25.5 in in both setups, A4 at 440 Hz
  • Strings: D’Addario archive PL010, PL013, PL017, NW026, NW036 and NW046
  • Setup A: E4, B3, G3, D3, A2, E2
  • Setup B: E4, B3, G3, D3, A2, D2

Result:

The total changes from 103.50 to 99.90 lbf. The first five strings match, and the sixth drops from 17.47 to 13.87 lbf. A unit weight of about 0.0004814914 lb/in at D2 would match the modeled E2 force at the same scale length.

Frequently Asked Questions

How much does Drop D lower tension on the low E string?

With the same string and scale, moving down two semitones multiplies the tension by about 0.7937. The worked example falls from 17.47 lbf at E2 to 13.87 lbf at D2.

Can I enter scale lengths for a multiscale bass?

Yes. Open the row’s Pitch, string source and scale controls and choose Measure this string. Enter the effective vibrating length between the contacts for each open string.

Why can two strings of the same gauge show different tensions?

Core shape, material and winding affect the weight per unit length. The formula uses that weight, and the matching diameter can have different unit weights across constructions.

How do I match the tension of an existing string in another tuning?

Put the reference string in Setup A at the same position and select Match Setup A in Setup B. The B row’s target unit weight uses the reference force together with B’s open frequency and vibrating length.

Why do the current manufacturer pack specifications differ from the archive?

The list uses published historical unit weights. Current pack specifications can use other manufacturing data and display rounding. Enter a verified weight for the particular current string when available.

What does a smaller high to low spread mean?

It means the highest and lowest modeled forces are closer in value. Compare the chart to see which strings account for the difference. Playing feel also depends on construction and setup.

Similar Calculators