Driveway Sealcoating & Crack Repair Quote Planner

Compare two maintenance quotes for an existing asphalt driveway. Measure each surface and its exclusions once, then assign its coats in each proposal. Use the selected product's coverage on smooth and porous asphalt to estimate a pail range. Separately measure cracks, choose geometric volume or product-label coverage, and price the work using your own quotes.

Existing asphalt takeoff

Compare driveway sealcoating and crack quotes

Examples use published coverage and illustrative prices. Enter the supplier terms and measurements for your project.

Proposal A

$676.00–$724.00

Coating work
1,020 ft²-pass
Sealer pails
3–4
Crack packages
1

Proposal B

$855.55–$945.55

Coating work
1,540 ft²-pass
Sealer pails
4–6
Crack packages
2

Proposal A is $131.55–$269.55 lower across the entered coverage endpoints.

  • Coat counts differ across measured zones.
  • Crack package coverage bases differ.

Complete quote for Proposal A. Complete quote for Proposal B. Proposal A is $131.55–$269.55 lower across the entered coverage endpoints.

Coating work, pails and cost ranges

Each measure shares a scale across proposals. Solid bars reach the lower endpoint. Striped extensions show the upper endpoint.

Proposal A

Area × coat count1,020 ft²-pass

Whole sealer pails3–4

Complete quote$676.00–$724.00

Proposal B

Area × coat count1,540 ft²-pass

Whole sealer pails4–6

Complete quote$855.55–$945.55

Measured asphalt zones

Drive footprint
Drive measured outer rectangle, 50 ft by 12 ft
Measured length
50 ft
Measured width
12 ft
Texture
Porous
Gross
600 ft²
Protected
80 ft²
Net
520 ft²

The bar shows protected and net shares of the area. The drawing gives only the outer dimensions.

  • Proposal A · 1 coat
  • Proposal B · 2 coats

Crack geometry and filler order

Measured crack group · ideal rectangular fill
Measured crack group fill cross-section, 0.25 in wide and 0.25 in deep
Length
165 ft
Width
0.25 in
Filled depth
0.25 in
Geometric volume
0.5357 US gal

Proposal A filler

Geometric fill

Included length
165 ft
Geometric volume
0.5357 US gal
Whole packages
1

Proposal B filler

Labeled linear coverage

Included length
165 ft
Geometric volume
0.5357 US gal
Whole packages
2
Edit surfaces and cracks

Measure each rectangle once. Enter protected area within that rectangle and the count of coats for each proposal.

1,020 ft² total net measured area

Surface 1
Surface 2

Crack measurements

Group measurements by width and filled depth. Check the proposals that include each group.

Crack group 1
Edit Proposal A coverage and prices
Sealer coverage per coat
Crack filler order
Entered rates and fixed scope
Edit Proposal B coverage and prices
Sealer coverage per coat
Crack filler order
Entered rates and fixed scope
Show materials and price ledger
Measured quantity and cost ranges for both sealcoating proposals
Quantity or costProposal AProposal B
Work area1,020 ft²-pass1,540 ft²-pass
Pail demand after reserve2.53–3.28173.96–5.1883
Sealer volume purchased14.25–19 US gal19–28.5 US gal
Filler volume purchased1 US gal2 US gal
Sealer pails$144.00–$192.00$180.00–$270.00
Crack filler packages$24.00$40.00
Coating labor$357.00$492.80
Crack labor$66.00$57.75
Preparation$75.00$70.00
Other quoted costs$10.00$15.00
Complete quote$676.00–$724.00$855.55–$945.55

Export results

Download sealcoating comparison CSV
Show selectable CSV text

How to use this calculator

  1. Enter measured asphalt zones, the areas to protect and the observed smooth or porous class.
  2. Give each proposal its own number of coats by zone. Enter the coverage range per as-sold package per one coat.
  3. Measure each crack group and select which repairs each proposal includes. Choose volume yield or the stated label coverage at the matching profile.
  4. Enter pail, package, labor and fixed scope prices. Review the ft²-pass, pail ranges and crack quantities next to the complete quote range.
  5. Inspect the quote ledger or export the measurements and both proposal estimates as CSV.

The Formula

The mathematical logic powering this calculation is:

Measure one to eight nonoverlapping rectangular asphalt zones. Net area is length × width less the measured area protected from coating. Enter each proposal's whole coat count, from zero to four, by zone. Multiply net area by coats for ft²-pass, and sum active work by texture class. Use each sealer rate in square feet per actual package per coat. High coverage yields low package demand and low coverage yields high demand. Sum each endpoint across the same sealer product. Apply its reserve and round each endpoint up to whole pails. Pail size is a separate input for showing purchased volume.

Enter zero to eight crack groups by measured length and representative width and filled depth. One geometric group needs 12 × length in feet × width in inches × filled depth in inches, in cubic inches. Divide by 231 to express that ideal rectangular volume in US gallons. Geometric mode pools the included volumes and divides by usable gallons per package. Label mode divides total included feet by the entered linear coverage per selected package. The selected crack groups must match the label's stated width and depth. Add the filler reserve after pooling, then round up to whole packages. Both modes show ideal geometric gallons. Product yield can differ from that ideal calculation.

Price sealer and filler by whole package, coating labor by ft²-pass and crack labor by included feet. Add preparation and other entered fixed amounts. Each line rounds to cents, with half-cent ties rounded upward. Zero active work contributes zero variable cost. Fixed amounts use the entered scope. A completed price range reflects the entered coating endpoints. The signed B minus A interval is [B low − A high, B high − A low]. Equal endpoints overlap. Review scope changes, including coat counts, crack groups or crack ordering basis, independently of cost.

Enter dimensions and coverage to three decimals and USD prices to two. Zone dimensions support 0.001–2,000 ft. Each crack group supports 0.001–10,000 ft length and 0.001–2 in width and filled depth. Reserve permits 0–100%. Quotes are bounded at $1 trillion. The worksheet uses written coverage and measured dimensions to estimate materials and quoted costs. Actual application, product compatibility, surface condition and field coverage require project-specific review.

Worked Example

If you input:

  • Measured asphalt: 500 ft² smooth and 520 ft² porous, after protecting 80 ft² of the measured drive
  • Coats: A has one coat in both zones. B has one smooth and two porous coats.
  • Sealer: 4.75 gal pails; 400–500 ft² smooth or 300–400 ft² porous per pail per coat; 10% extra
  • Crack repair: 165 ft measured at 0.25 × 0.25 in; one US gallon per pack. A uses geometry. B uses the stated 150 ft per pack.
  • A entered costs: $48/pail, $24/filler pack, $0.35/ft²-pass and $0.40/ft of cracks plus $85 fixed
  • B entered costs: $45/pail, $20/filler pack, $0.32/ft²-pass and $0.35/ft of cracks plus $85 fixed

Result:

A measures 1,020 ft²-pass and buys 3–4 sealer pails and one filler package for $676.00–$724.00. B measures 1,540 ft²-pass and buys 4–6 sealer pails and two filler packages for $855.55–$945.55. The crack geometry is about 0.5357 US gal for both, and B’s labeled basis gives a distinct purchase quantity.

Frequently Asked Questions

Does a second coat double the driveway size?

The footprint stays the same. A second coat increases the area multiplied by coat count, measured in ft²-pass. The worksheet uses that work quantity for material and coating labor.

Why enter a coverage range?

The same pail can cover a different area on smooth and porous asphalt. Enter the range per package per coat for each class. Your whole-pail order can differ at its two endpoints.

Should I use extra reserve when the label includes a loss factor?

Enter the product rate as stated and include only any additional stock you plan to buy. Some practical coverage rates already account for material loss.

How do geometric and labeled crack coverage differ?

Geometry estimates the volume of a rectangular void from the measurements. A product label can quote fewer feet for the same nominal cross-section. The worksheet keeps both values visible and uses the basis you select.

Can I compare a crack-only bid with a coat-only bid?

Yes. Use zero coats or clear the crack group inclusions for that proposal. The cost comparison highlights changes in the entered work.

Does the estimate include setup and surface preparation?

Use the Preparation and Other quoted costs fields for the exact amounts in your quote. The worksheet applies each fixed line as entered, even with no variable work.

Similar Calculators